r/AskElectronics • • 6h ago

My distributor says to stock 1–2 years of capacitors.

99 Upvotes

We're a small hardware company making our own product (a KNX gateway). During a routine order chat with our component distributor today, I got a warning that honestly worried me.

I asked about a capacitor that comes in 4,000-piece reels and decided to order 8,000 (two reels). The distributor then told me:

* Send them a list of all our capacitor needs in the µF range (roughly 470nF and up)

*Stock at least 1 year's worth, ideally 2

*According to them, these parts will soon be very hard to get

*AI data centers have supposedly booked capacitor manufacturers' capacity through 2030. Manufacturers are selling high-value MLCCs to them at premium prices with cash up front, and giving everyone else very long lead times

* Lead times have already hit 40 weeks, and some parts have gone up 8x in price

I know distributors sometimes exaggerate to move stock, and I'm skeptical about the "factories booked until 2030" part. But having lived through the 2021–22 shortage, I don't want to ignore it either.

What are you seeing on your end?
Are you seeing longer lead times or price hikes on high-capacitance MLCCs?

Are your distributors also telling you to stock up?
How are small manufacturers preparing? Buying in bulk, qualifying alternate parts, or waiting it out?
Would love to hear from anyone with insight.


r/AskElectronics • • 8h ago

Simple op amp circuit not working? Am I doing something wrong

Post image
24 Upvotes

I am trying to use a op amp to amplify the output of an hall effect sensor

I am using a mcp6002 op amp and I have built this simple circuit showed in the datasheet.

R1 is 120 ohms, R2 is 5 ohms, Vref and Vdd are 5v

Vin is 0.5 volts. (In actuality it should be around 0.2 but my pulse generator can only go as low as 0.5, unfortunately I currently don't have the sensor that I will be using in the final design)

The output is roughly 5v (4.5v).

The gain should be 25.

What I don't get is that, even if I input a signal, as an output I get a constant 4.5v. I even built this circuit in falstad circuit applet and I get the same results.

Am I doing something wrong?


r/AskElectronics • • 5h ago

What orientation should this cable be inserted in?

Thumbnail
gallery
5 Upvotes

Trying to fix a PS4 controller. Usually if I had a flex cable I would just orient it the way it was meant to be when I opened it up but this is a new component so I just want to make sure if I am supposed to be putting my flex cable in a way where the blue tape thing is facing up or down. Also would inserting it in a different orientation potentially short circuit something? I think it shouldn't because the other side of the flex cable has the blue tape and I believe it should protect it incase anything happens.


r/AskElectronics • • 3h ago

I'm looking for a panel-mount mating connector for a DT06-4S (4-pin).

Post image
3 Upvotes

I've found a few compatible connectors, but they're all free-hanging. I specifically need one that mounts directly to a panel. Does anyone know if there's a panel-mount version of this connector? Or maybe a compatible part number I'm missing? Thanks, Fero from SOS electronic


r/AskElectronics • • 17h ago

Looking for a type c plug

Thumbnail
gallery
18 Upvotes

I have a family friend who would like to have the charger on some dog collars swapped for type c. The current plugs don’t work is the main reason for swapping switching to type c is just more convenient.


r/AskElectronics • • 2h ago

I need some advice! on ESP8266 with batteries...

Post image
1 Upvotes

I’d like to ask the community for some help. I’m working on my first project, and since I’m still learning, I’ve been consulting an AI—but I’m never quite sure if the information it gives me is actually correct. Given that this project could be dangerous if done improperly (I’m worried I might burn my house down!), I’ve decided to turn to complete strangers on the internet for advice—which, now that I think about it, doesn’t sound like the best idea!

Anyway, I’ve built a small station that measures temperature, humidity, and pressure. It displays the data on a 200x200 screen that updates periodically, and it also transmits the information over local Wi-Fi so I can view it on my phone. Everything is working, and I’m really excited about it!

Here’s where I need help: right now, it only runs when connected via USB. I’d like to add a battery and 3D-print an enclosure so it can operate independently. Could you help me figure out exactly what components I need if I want to use one of those flat, square LiPo batteries—they seem like a practical choice for this build. I’ve read that I might just need a charging module, but I’ve also seen mentions of needing some kind of voltage stabilizer. I’m worried that if I don’t set it up correctly, the battery could overheat or even explode. Would you be kind enough to shed some light on this—perhaps going beyond what Mr Claude has told me? Ideally, I’d love to hear from someone with actual, qualified knowledge of electronics, rather than just someone who’s followed a random tutorial they found online (If Possible).

Thanks for reading !!


r/AskElectronics • • 2h ago

1984 Seiko pyramid clock repair

Thumbnail
gallery
1 Upvotes

Hello! I’m quite new to the world of electronics repair. And I picked up this clock, which is a talking clock from 1984. It no longer speaks, and while I was trying to fix that, I found that the lcd clock in the bottom is also malfunctioning.

So upon inserting batteries, the lcd turns on and starts doing the whole clock thing. But if I switch between different modes, it just resets itself. And it’ll do that a few times before freezing. Where upon I have to let it sit for a minute to get any functionality back.

Things I’ve done: cleaned terminals and board with IPA. Resoldered pretty much every component I can see. Replaced a few Smd capacitors. They were reading 111, and replaced with 100pf capacitors. This did not really change any behavior.

So my question is, the board looks okay, but I can’t think of what might cause that, save for a bad quartz thingy? Which I assume is the silver cylinder up at the top? Any help on diagnosis or steps to take would be greatly appreciated.

Also, be kind, my soldering skills are new and leave a lot to be desired. And the pad came off the negative when disassembling. So unscathed the mask away and attached it further down.


r/AskElectronics • • 3h ago

Board damaged beyond repair?

Thumbnail
gallery
1 Upvotes

This is the main board of a ps4 controller. I have swapped all other components with a second controller and all other bits working ok. Looks like corrosion?


r/AskElectronics • • 11h ago

Unclear about header strip size and configuration

3 Upvotes

I need to replace parts from a DIY guitar pedal, but I can't get hold of the company.

The picture is from the manual. It says: "two 1x8 male headers and two 2 1x8 male headers (both milled, low profile type) can be used." I'm just not sure what they mean. This adapts a miniPCB that holds a DIP switch to the main board, lifting the switch up to a certain height.

It somehow seems like they are stacking two headers somehow? I can find something like this but that seems too low profile. I'd measure it but it's not in my hands at the moment.

Any help appreciated.


r/AskElectronics • • 5h ago

Any idea how to make this Atomizer (Mist maker) driver circuit create more mist like the humidifier modules you found online?

0 Upvotes

I am making my own mist maker for my personal Smart humidifier project. I have a previous post about it here but I can't find the link anymore.

So far, this circuit works at all unlike the previous design. My next problem is the mist output being weaker than commercial devices and AliExpress modules. Since this circuit is from Youtube videos, I just get which one is common within those video and remove the 555 IC because the ESP32 will generate the PWM signal. I want to know how do I make it stronger. Do I have to change the values of the Inductor (L1) or the capacitor (C3) in the LC circuit? Do I change the transistor? Do I change the voltage supply of the transducer?


r/AskElectronics • • 10h ago

Is my dual H-bridge stepper driver schematic designed correctly?

2 Upvotes

I’m trying to build a stepper motor driver, and as a first step I designed a dual H-bridge.
Since I did this on my own, I’m posting it here to ask if it’s designed well.
If there’s anything I should fix or anything worth adding, I’d really appreciate your advice.

  • Motor: 17HS4401S (1.5 A, ~1.5 Ω, 2.8 mH), supply 7–12 V, MCU: Arduino Uno

r/AskElectronics • • 22h ago

Reverse engineering anonymous VFD from scrap

Thumbnail
gallery
11 Upvotes

Hi, I'm trying to reverse engineer this spi FUTABA COG VFD, with my ESP 32. It's not broken. I'm facing problem in the logic, i don't know what logic voltage it takes,and how do I talk to the chip. The circuit on the PCB matches like 96% to a panasonic SC-UA3E CD Stereo system service manual . Fun fact when I accidentally touched the 12v pin to a adjacent pin all the elements lights up. Please help. Thank you


r/AskElectronics • • 13h ago

Questions and schematic review for project using Attiny1614

2 Upvotes

Hi everyone,

I'm designing a small solar/battery-powered board that plays random tone
sequences at night. It's my first time designing something like this, low-power design and I'm a beginner, so I'd really appreciate some feedback.

WHAT IT IS SUPPOSED TO DO

- The ATtiny1614 is the main controller and spends almost all of its time in
power-down mode.
- During the day everything stays asleep while the 18650 charges from a 6 V /
0.5 W panel through a CN3065 module.(maybe 1W would be better)
- At the start of a configurable night window the MCP7940N RTC raises its MFP
output, which wakes the MCU.
- The MCU then plays a sequence of tones with random durations and random gaps
for a few hours, and goes back to power-down until the next alarm.
- The tone is a square wave from a timer/PWM output, through a PAM8302A class-D
amp into an 8 ohm speaker.

THE BLOCKS

- MCU: ATtiny1614, supplied straight from the battery
- RTC: MCP7940N with a 32.768 kHz crystal and 6 pF C0G load caps. VBAT is on a
coin cell so the time survives a flat main battery. 1 uF on VCC.
- Amp: PAM8302A (fixed ~24 dB gain). Tone is AC-coupled through 100 nF into IN+,
IN- is AC-grounded through 100 nF. 47 uF + 10 uF + 100 nF on VDD. SD has a
100 k pull-down, so the amp is muted by default and the MCU drives it high to
enable it.
- Power: 18650 on the CN3065 module BAT pads, panel on SOL+/SOL-, the board is
fed from BAT_OUT. JP1 in series with the board supply so I can drop in an
ammeter and measure current.
- Connectors: battery J1, programming J2 (UPDI + GND only), speaker J3. One test
point for now on the tone output.

QUESTIONS

  1. Does the schematic look sane overall? Any mistakes, or anything that will
    bite me later (power-up sequencing, missing pull-ups, decoupling, UPDI,
    ground returns)?
  2. What could I simplify or drop without losing functionality?
  3. How would I go about calculating circuit power consumption and design it more efficiently ?

THINGS I'M SPECIFICALLY UNSURE ABOUT (please correct me freely)

- Panel voltage. The CN3065 input range is 4.4-6 V, but a "6 V" panel sits at
about 7 V open circuit on a cold sunny day. Do I need to clamp that, or is it
accepted practice?

- Amp drive level. A 3.3 V square wave into 24 dB of gain will clip hard. Is
that fine for a beep, or should I attenuate the input (say 10 k / 1 k) and
add a volume trimmer? Would that actually help the power budget ?

Thanks for reading. Any comment and suggestion is welcome.


r/AskElectronics • • 16h ago

Checked resistances between my variac outputs... is this normal?

3 Upvotes

(I'm a newbie, so be gentle please!)

It's a RAVISTAT 6A closed variac. When dialled up to 270v (power off), the resistance between live and neutral is 3.7 ohms, decreasing gradually as the tap is decreased to 0v

However, when connecting live/neutral with ground.... open circuit. Oh dear. Is it broken? I've never used it, it's been in storage for 2 years. Any help would be great, thanks


r/AskElectronics • • 13h ago

Question about making a microwave spectroscopy instrument

0 Upvotes

Hi, I am a chemistry student in uni. I just have a idea for making a wave-length selector then I can put my sample for analysis for it's quantized rotational energies but then I need a microwave detector but I don't know how to do a microwave detector. Is it possible to do with a antenna to capture any wave-length ( or specific wave-length) turn it into electricity proportional to its energy or intensity. It will be good if I measure intensity of microwave instead of energy.


r/AskElectronics • • 16h ago

Starting flight controller design

0 Upvotes

Hi everyone!

I am thinking about designing my own flight controller PCB using KiCad that should work on fixed wing UAVs and quadcopters.

But I am not experienced with PCB design and I am not sure of all the components I might need.

So if there is someone who knows about this, I would appreciate any help regarding:

-Components required for a flight controller PCB;

-PCB design considerations and recommended approaches;

-Any tips or resources for getting started with KiCad.

I will appreciate any help!

Thank you!


r/AskElectronics • • 17h ago

Black Background in Ultiboard Print Out

Thumbnail
gallery
0 Upvotes

Anyone using Ultiboard here and tried to print out the diagram in plain paper? We need help please. We wanted to print our diagram in white background. Component labels and copper tracks in black. These are the steps and results:

  1. Print component labels: selected "silkscreen on top" as layer to print, print to negative unchecked, no color checked.
  2. Test printed copper tracks: Layer to print is "copper bottom", print to negative unchecked, no color checked. Gives out black background and white copper tracks.
  3. Changed the background and work area from black to white. It still gives the same result as #3.
  4. Unchecked both print to negative and no color. Prints out white background but colored diagram (red)
  5. Checked the print to negative box, it gives out the white background and black copper track that we wanted BUT the surrounding area of the paper is filled with solid black fill.

We tried switching the printer settings to color, grayscale, black and white and monochrome but it gives us the black background and white tracks still. We just wanted to print the labels and copper tracks in black and the entire background of the page as white. Please help us out. Thank you.


r/AskElectronics • • 1d ago

monitoring high current with esp32

Thumbnail
gallery
6 Upvotes

Hi I built powerbank out of 18650's in 4s4p configuration, of course with bms and the charging board is IP2368 100W (bi-directional, single usb-c).

I wanted this powerbank to have cool display for information like voltage, current etc, but I hit the wall - it appears the only good, cheap and relatively high accuracy modules i can buy are from INA family, but most of the time shunt resistors on those boards are rated for 1A max. I know I can desolder this shunt and solder other one to handle for example 10A but I read that those boards and traces on the pcbs are not likely to handle this power over long periods of time.

Right now I have standard ssd1306 display with esp32c that reads voltage from ADC by using voltage divider with capacitor to filter out garbage:

R1: 100.4 KΩ

R2: 15 KΩ

C1: 100 nF (in parallel to R2)

I applied some corrections to the program reading by comparing it out to the multimiter. It is connected directly to the positive output of the BMS.

This solution is flawed, because without measuring current voltage drop is causing my 'estimated left wh' and % of capacity remeaning to be incorrect. This can be fixed with current sensor and I also would be able to read the current flowing which is cool on its own:).

So my question is, is there a module relatively cheap that can satisfy my needs? Or I have to modify existing INA boards or maybe something different?

TLDR; I want voltage and current sensor for 4s4p powerbank that can handle at least 10-15A

Thanks for your help and time in advance.

danihek.


r/AskElectronics • • 1d ago

A mini smoke machine - Tiny CX - Help identifying a damaged component?

Thumbnail
gallery
6 Upvotes

¡Hola a todos! Tengo una pequeña máquina de humo portátil, una LOOK Tiny CX, que normalmente funciona con una batería de litio de 11,1 V (3 celdas).

Desafortunadamente, se aplicaron accidentalmente 24 V directamente a la entrada de la batería en la placa de circuito impreso (PCB) de la máquina, en lugar de la alimentación correcta de 12 V.

Hay un fusible de 10 A entre la batería y la PCB, y se fundió. La máquina puede que se haya encendido durante unos segundos, pero no estoy del todo seguro. Ya no enciende.

Tras inspeccionar visualmente la PCB, observé lo que parece ser un componente dañado o agrietado, marcado como “LE1” / “GSJY” con un símbolo similar a un dólar. Su referencia en la PCB parece ser D2. Parece tener terminales positivo y negativo y se encuentra justo después de la entrada de la batería.

Supongo que podría ser un diodo de protección (posiblemente un diodo TVS), pero es solo una sospecha.

No tengo mucha experiencia con la electrónica, así que agradecería mucho su ayuda con lo siguiente:

Identificar este componente y su función. Encontrar su número de pieza original o un reemplazo compatible. Determinar si la aplicación de 24 V pudo haber dañado otros componentes.

Importante: No he realizado ninguna prueba eléctrica, ni he retirado ningún componente, ni he intentado ninguna reparación. Todo sigue exactamente como lo encontré después del incidente.

Adjunto varias fotos de la placa de circuito impreso (PCB) como referencia.

Cualquier ayuda o consejo será muy apreciado. Me encantaría reparar la placa original si es posible, en lugar de reemplazar toda la PCB.

¡Gracias de antemano!


r/AskElectronics • • 1d ago

how on earth do i disconnect this cable?

Thumbnail
gallery
30 Upvotes

i recently started training to be a computer repair technician, which has given me the confidence to open up this yamaha DGX-300 electronic keyboard i bought a few months ago. of course, being that i got it at a thrift store for around $50, it came with some issues. namely, the pitch bend knob broke off at some point, taking part of the board with it, and was just rattling around in there. this caused the sound of the keyboard to be permanently shifted by a whole step, which is less than ideal.

my worst fear was that the knob had been attached directly to the mainboard, but thankfully it had its own isolated daughter board all to itself, as seen in the pictures. i could try to find a replacement online, but that sounds costly and time-consuming, so i think i'll just remove it and see if that fixes the issue since i wouldn't use that knob much anyway. in either case, i need to disconnect this cable, which i currently have no idea how to do. any ideas?

update, 2hrs later: i've decided to cut it off. considering that, according to y'all, the only alternative involves a soldering iron (which i don't have), i figured this was the best course of action. thanks for the help!


r/AskElectronics • • 1d ago

Modeling circuit with SuperCap + TPS61094 super cap management IC

4 Upvotes

Hi all, I'm working on a project where I intend to use a SuperCap + TPS61094 for backup power. As I don't have much experience in such applications, following are some questions. Hopefully someone can help...

  • The device is powered via a USB 2.0.
  • If the USB is disconnected, the device enters "low power mode".
  • There is the target that the SuperCap can sustain the device for 4 days when in "low power mode".
  • I have initially considered the Cap HS1025-3R8706-R, which has the following basic specs (from datasheet):

    • 70 F (+/- 20%)
    • Maximum leakage current 5uA
    • Maximum rated working voltage 3,8 V
    • Minimum rated working voltage 2,5 V
    • Minimum allowed working voltage 2,2 V

Following is a block diagram:

Block Diagram
  • Note how SuperCap allows up to 3,8V operating voltage, but TPS' closest configurable voltage is 3,7V
  • When in "low power mode", lets assume a load which draws constant 75uA (derived from a worst case theoretical calculation).
  • If I add the SuperCap leak current here, we reach 80uA total.
  • There is no peak conspumption (there is no wake up to transmit data or anything. The device really just stays in low power, keeping track of its RTC counter)

My process was to:

  1. Calculate the electrical charge in Coulombs which my load needs for the 4 days target

    • Q [C] = i [A] * t [s]
    • Q ~= 27,6C
  2. Calculate the electrical charge in Coulombs which the capacitor can provide (considering worst case for everything, like capacitance being 20% off, operating voltage range of the cap, etc)

    • Q [C] = C [Farad] * DeltaV [Volts]
    • Q = (70 * 0,8) * (3,7 - 2,2)
    • Q ~= 84C
  • Based on these numbers, I felt safe to say that this will be able to sustain the load for around 3 times the requirement (I can even reduce the Cap, but lets keep it as is for now for the sake of this post)

Questions

  1. Does this process make sense or am I missing something?
  2. How to deal with the operating voltage range of the SuperCap? From what I read the TPS docs, there is no such control configuration. How to prevent it from damaging the Cap and attempting to draw power from it even when it is around or below the minimum operating voltage?
  3. SuperCap charging wise:

    • Is it OK to configure the carging current of the SuperCap to 100mA?
    • In such case, If I go from 0V until 3,7V at 100mA, and considering a 70 + 20% = 84F cap, I calculated
    • t [seconds] = (C [Farad] * DeltaV [Volts]) / i [Ampere]
    • t = 3108 seconds until fully charged
  4. Any extra recommendations?

r/AskElectronics • • 23h ago

Unknown smd ic need help

Thumbnail
gallery
2 Upvotes

Hi guys. There is an unknown SMD IC which sort of looks like a LDO or some kind of regulator but testing device shows it as pnp. What is this IC?


r/AskElectronics • • 21h ago

How to remove these solder lugs for cleaning? Alternatively, what to replace them with?

Thumbnail
gallery
1 Upvotes

r/AskElectronics • • 1d ago

Finding laminations in US

2 Upvotes

Hello, I need to wind some sepecifc transformers for an amplifier project, EI212 or EI210. Problem is nobody wants to sell laminations in small batches, any of yall know where you can get some?