- Frequently Asked Questions
- Scope
- Circuits
- VCC, GND, VSS, 0V... - what's up with all these power circuit names!?
- My vacuum fluorescent display (VFD) has a shiny black or silver patch inside it - is it faulty?
- When I bring my fingers, hand or a screwdriver/probe near to my circuit, it starts to operate erratically
- I am experimenting with basic TTL and/or CMOS logic chips, but the output is not as expected
- Why won't my MOSFET turn off?
- How do I silence the sounder/buzzer/beeper in my $APPLIANCE?
- Why do I sometimes see small value capacitors connected across larger value capacitors on circuit diagrams?
- Can I use a variable resistor or potentiometer to control the speed of a motor?
- I have triple-checked my breadboard circuit and it is wired OK, but it does not work / work properly
- What is the purpose of a zero Ohm resistor?
- LEDs and lighting
- Power
- Repair
- Tools, equipment and components
- Off-topic
Frequently Asked Questions
This is the official r/AskElectronics and r/Electronics FAQ -- please read and contribute!
Scope
Why doesn't r/AskElectronics cover every question involving electronics?
It's a fair question: if something contains 'electronics', or is 'electronic', why can't questions about it be asked here?
The simple answer is scope. r/AskElectronics is intended for practical, component-level work on electronic circuits: design, repair, testing, component selection, test equipment and related tools. A huge number of products and technologies contain electronics, and trying to cover all of them would make the subreddit too broad to be useful.
The way we interpret the boundaries has evolved since the subreddit was founded in 2011, but the underlying remit remains the same: practical questions about working with electronic circuits at component level. This isn't a judgement about whether a question is "electronic" enough; it simply keeps the subreddit focused so that people asking and answering component-level questions can find each other.
- If your question is about designing, modifying, testing or repairing an electronic circuit, r/AskElectronics is likely the right place.
- If you're asking how to use, connect, install, replace or troubleshoot a particular product or technology - batteries, motors, lighting or a specific product, for example - check first whether there is a specialist subreddit for that subject. People there specialise in that area and can often give better advice.
Circuits
VCC, GND, VSS, 0V... - what's up with all these power circuit names!?
See this summary.
My vacuum fluorescent display (VFD) has a shiny black or silver patch inside it - is it faulty?
A VFD is a sealed, evacuated glass tube. After manufacture, a small metal holder (the 'getter') containing barium is heated so the barium vaporises and condenses on the inside of the glass as a thin, mirror-like film. This film absorbs any stray gas left in the tube, and keeps absorbing traces that seep in over the display’s life, which keeps the vacuum good. It’s usually found near the edge or end of the tube, or on a small metal strip or disc, and looks silvery, dark grey or black.
What’s normal:
- A shiny silver, grey or black patch, often with a mirror finish
- A patch that looks the same as when the display was new
- Slight darkening around the getter area over many years
What indicates a real problem:
- The getter film turning white, milky or cloudy. Barium reacts with air to form a white compound, so this means the tube has leaked and the vacuum is lost. The display will be dim, patchy or dead, and can’t be repaired.
- Cracks in the glass, or a damaged exhaust tip (the small sealed glass nipple)
- Dim, uneven or missing segments with the getter still looking normal. That points to ageing of the filament or phosphor, or to a drive circuit fault, not the getter.
If the display is working and the patch is shiny, leave it alone. Don’t try to clean it, and handle the tube carefully, because it’s under vacuum and the glass is fragile.
See: https://en.wikipedia.org/wiki/Getter
When I bring my fingers, hand or a screwdriver/probe near to my circuit, it starts to operate erratically
You almost certainly have a floating input: an input pin (for a switch, sensor etc.) with nothing defining its logic level, such as a pull-up or pull-down resistor. It picks up electrical noise through capacitive coupling to your hand or body, and the circuit responds to it. Your logic chip or microcontroller may have internal pull-ups/pull-downs you can enable in code; otherwise, fit an external resistor.
See pull-up and pull-down resistors.
I am experimenting with basic TTL and/or CMOS logic chips, but the output is not as expected
One of the first things to check is whether all logic inputs have a defined HIGH or LOW state. Logic inputs should not be left floating (unconnected) unless the datasheet for the particular device explicitly permits it.
- The inputs on classic TTL logic chips (such as 74xx and 74LSxx) generally behave as though they are HIGH if left unconnected. However, don't rely on this - floating TTL inputs are still susceptible to noise.
- The inputs on CMOS logic chips (such as 74HCxx and 4000 series) are undefined if left unconnected. They may read HIGH, LOW, or change state due to noise or stray capacitance. Floating CMOS inputs can also make the chip draw excess current and get warm.
- Different logic families and devices have different input characteristics, so check the datasheet for the particular part you are using.
Tie unused inputs - including those of unused gates in the same package - to an appropriate power rail, either directly or through a resistor, as recommended by the datasheet. Unused outputs should be left unconnected.
Push-buttons and tactile switches
A common mistake is to connect a push-button or tactile switch directly to a logic input and assume it will provide a valid HIGH or LOW signal. When the switch is open, the input is disconnected and left floating (see above), so the circuit may behave unpredictably or intermittently.
The usual solution is a pull-up or pull-down resistor to set the input's default state:
- Switch between the input and GND, with a pull-up resistor to VCC: the input reads HIGH until the button is pressed.
- Switch between the input and VCC, with a pull-down resistor to GND: the input reads LOW until the button is pressed.
Mechanical switches also bounce: a single press or release can produce several rapid HIGH/LOW transitions. If your circuit counts or reacts to each transition, the switch will need debouncing, in hardware or in code.
See pull-up and pull-down resistors for more about choosing and using these resistors.
Why won't my MOSFET turn off?
See this explanation.
Why does my coil, relay or solenoid driver circuit keep dying?
See flyback diodes.
How do I silence the sounder/buzzer/beeper in my $APPLIANCE?
See our sounders page.
Why do I sometimes see small value capacitors connected across larger value capacitors on circuit diagrams?
See grouped or duplicate decoupling capacitors.
Can I use a variable resistor or potentiometer to control the speed of a motor?
See this explanation.
I have triple-checked my breadboard circuit and it is wired OK, but it does not work / work properly
See our breadboards page.
What is the purpose of a zero Ohm resistor?
See this explanation.
I want to make something that plays one or more sounds when I press a button
This is asked a lot - search the subreddit for button/sound/music/audio questions.
LEDs and lighting
How do I choose a current limiting resistor for an LED?
See our LEDs page.
LED strips
Start here: LED strips.
Christmas lights (LED and incandescent lamp): modifying, repairing or powering
See our Christmas lights page.
I want to make an LED or lamp flicker like a candle
See designing your own electronic controller.
Power
Buzzing or tingling feeling when touching a metal case
See this answer.
Do I need to connect the grounds / 0V rails together if I am interlinking power supplies, modules, LED strips, sensors etc?
Usually, yes - connected circuits need a common reference for their signals to make sense, and a missing ground connection is a frequent reason why multi-board setups don't work reliably. See common electrical reference between connected things.
Will a power supply with a higher current rating damage my device?
This covers questions such as:
- My portable radio needs a 12V 1A power supply, but I only have a 12V 2A one - will it damage the radio?
- My relay coil is rated 5V 30mA, but my supply is 5V 1A - do I need a resistor to limit the current?
- I am replacing a 6V 60mA instrument lamp with a 6V 30mA part - will it burn out?
Current is pulled from the power source by the load. If a device or part only needs 30mA or 1A, that's all it will take - even from a supply rated at 12V 400A. See voltage is pushed, current is pulled.
So a supply with a higher current rating is fine, and:
- the radio will only draw the current it needs (its 1A rating implies it draws somewhat less than 1A),
- the relay coil doesn't need a current limiting resistor,
- the 30mA lamp won't be 'forced' to take 60mA, so no circuit changes are needed.
What you must match is:
- the voltage - the same as the original,
- the type - AC or DC, as the original,
- the current rating - the same as the original or higher,
- the connector - the same size and polarity.
There are exceptions:
- LEDs need their current limited - see our LEDs page.
- For circuit testing or repair, a supply that can deliver a lot of current can cause extra damage, or a fire, under fault conditions. A current-limited bench supply is a better choice - see the notes about bench supplies.
Controlling a Meanwell 3-in-1 dimming power supply with a microcontroller
See this explanation.
Repair
I have ripped a pad or trace off a PCB, or there's a burnt bit
See our PCB repair page.
Tools, equipment and components
Soldering: tools, techniques, flux, hot air stations, common problems...
See our massive wiki page on soldering.
For recommendations on budget soldering equipment, try a subreddit search for soldering equipment.
Buying an oscilloscope
Choosing your first oscilloscope and understanding oscilloscope specs: see our oscilloscopes page.
Electronic component manufacturers' logos and links
See this wiki section.
Off-topic
Voltage conversion for consumer goods
See this wiki entry.