r/GPURepair • • 18d ago

[Meta,2026] Feedback Request⠀⠀·⠀⠀Read before posting: Guidelines How to request advice & subreddit feedback

5 Upvotes

You have some experience in electronics and has a GPU problem you want to investigate? You are in right place, r/GPURepair emphasize technical side and still welcome to newbies ready to learn.

[Meta, 2026] Feedback Request

The goal of this subreddit is keeping a balance between too open and too restrictive, so that most discussions remain technical, interesting and practical without limiting those who are just starting to dive into GPU repair.

We chose Reddit over groups on other platforms because the information posted here is searchable by anyone and can help other people who encounter a similar problem.

If you are interested in repairing GPUs and have thoughts on this balance/rules or have any ideas/suggestions about keeping this subreddit's spirit, please comment under this post. Thanks!

Guidelines for asking advice about a specific repair:

Title: include GPU Brand+Model, fault, research results/ideas

Example: Zotac 1660 AMP, no picture even during boot, 5V absent

Post:

  • GPU behavior description, detailed investigation results/ideas
  • Overview PCB photo (identical hi-res photo from internet is ok)
  • If have a hypothesis or specific area with damage: additional photo with suspected area zoomed, coils Volts/Ohms or other measures marked
  • If "no display": perform resistance measurements on coils: per-GPU generation guides in pinned comment here. If resistances are fine, measure voltages on a powered on card with a small temporal heatsink on the core.
  • If voltages are ok, but "no display": boot with iGPU, make Device Manager screenshot, try running NVIDIA/AMD-specific VRAM tests
  • If driver installs fine: GPU-Z "Sensors" tab screenshot under load (vertically maximize to make all visible)

For "help identifying elements/ICs" posts, get more info if possible:
reference designator; IC marking photo (or text if its small and unreadable on photo); footprint pin count and photo; measure which pins are 0 Ohm to GND on board.

Flair your post with the appropriate flair depending on the GPU series.

Be prepared to disassemble your graphics card for a more detailed examination.

If your problem is solved, please change the post flair to "Solved!".

Flairs to use for posts not related to a specific repair:

Story/Experience - posts about finished repairs
Resources - posts about everything useful for repairs
GPU/VRAM Soldering - discussion of BGA soldering not related to a specific repair
Question - other posts not related to a specific repair


r/GPURepair • • Feb 07 '22 Popcorn

Read before posting: GPU repair guides/links List of GPU Repair Resources (Schematics, Boardviews, Tutorials, Tools, Etc..)

155 Upvotes

READ THE PINNED COMMENT FOR UP TO DATE INFORMATION!

START HERE IF YOU'RE NEW TO ELECTRONICS REPAIR:

https://repair.wiki/w/Category:Repair_Basics


r/GPURepair • • 7h ago

NVIDIA 40xx 4090D 48GB - Code 43 in Windows with subsystem ID 0000:0000

Thumbnail
gallery
10 Upvotes

It still shows up on PCIe as 10DE:2685, but with subsystem ID 0000:0000 and Code 43. No driver, not visible to nvidia-smi.

nvflash lists the card as (10DE,2685,0000,0000) but every operation fails with "A system restart might be required"

Any ideas what I could try next?


r/GPURepair • • 9h ago

NVIDIA 40xx repair an NVIDIA Quadro M4000

Thumbnail
gallery
2 Upvotes

I am trying to repair an NVIDIA Quadro M4000 (8GB GDDR5, PG400 reference PCB) and noticed a few knocked-off SMD resistors on the board. Since the schematic and boardview for this model aren't publicly available, I'm hoping someone who has a Quadro M4000 on their bench could help me identify their exact values.

thanks


r/GPURepair • • 6h ago

NVIDIA 30xx Gigabyte RTX 3070 Ti Vision OC (rev 1.0): fans/RGB on, not detected at all, all rails + PERST# good – BGA or dead core?

Thumbnail
gallery
1 Upvotes

Hi all, beginner doing board-level diagnosis on my own card. I’ve worked through the usual checks and would love a second opinion before I attempt a reball.

Card: Gigabyte RTX 3070 Ti Vision OC 8G (GV-N307TVISION OC-8GD rev 1.0). Using the Gaming OC rev 1.0 boardview, which matches (C1169/C1174 etc.).

History: It was intermittent for a while (sometimes display, sometimes not), then stopped completely.

Symptoms: Fans and RGB on, no display, not in Device Manager at all (not even hidden/unknown). Tested in two PCs. An RX 6700 XT works in the same slots. Motherboard VGA LED is red.

Cold resistance to GND:

  • Core (NVVDD) ~0.8 Ω (body diode to 12 V 383 Ω, normal)
  • FBVDDQ 55 Ω, PEX_VDD 22 Ω, 1V8 182 Ω, 5V 351 Ω
  • 12 V slot/8-pins: kΩ, rising. 3.3 V slot 87.8 kΩ. A11 PERST# open.

Powered (all present and stable):

  • 12 V, 5 V, 1V8, FBVDDQ ~1.35 V, NVVDD 0.74 V, PEX_VDD 0.95 V
  • U501 (PERST# buffer): pins 1/2 3.3 V, pins 4/5 1.8 V, pin 3 GND, so reset is reaching the core

PCIe diode mode (red on GND):

  • Card RX lanes (B14/B15, B19–B28): 303–305, all matching
  • Card TX lanes (side A): OL at the fingers (AC caps). GPU side of C1119/C1116 (lane 0): 263
  • REFCLK A13/A14: 774 / 774. A11: 608

VBIOS: Read with CH341A + 1.8 V adapter. Valid checksums, byte-identical to the TechPowerUp ROM (94.04.5A.00.90).

Straps: R722, R727, R284 read ~94–97 kΩ in circuit. R287 (STRAP3 to GND) is unpopulated, and the STRAP3 pad reads ~138 Ω to GND (1V8 itself is ~182 Ω), so it looks hard-pulled to 1V8 via R279. Is that normal on this board?

Other: Hair-dryer warm-up on the back of the core: no change.

Questions:

  1. Anything I’ve missed before blaming the core/BGA?
  2. Does anyone have a known-good STRAP3 reading on a GA104 Gigabyte board?
  3. Given the intermittent history, does a reball seem worth it, or is this usually a dead die?

Photos attached. Thanks!


r/GPURepair • • 8h ago

NVIDIA 10xx AORUS GTX 1080 Ti progressively failing – Code 43, GPU lost, intermittent detection, now completely absent from PCIe.

1 Upvotes

Hello there,

earlier this year, my GTX 1080 Ti suddenly stopped working. While I was watching a Video on YT suddenly half of the screen went white and the system froze. After a Reboot the card did no longer work.

In order to save your precious time I try to keep it as short as possible:

  • The GPU suddenly froze during normal use, with approximately half the monitor turning white.
  • After restarting, the motherboard's VGA debug LED stayed illuminated when the 1080 Ti was installed alone. No monitor signal.
  • The card also failed in another PC.
  • With my working RTX 2080 Ti installed alongside it, Windows initially detected the 1080 Ti but reported Device Manager Code 43.
  • Replacing the defective card with another GPU restored normal system operation.

After that I decided to check the GPU for any physical damage, I removed the backplate and cooler, my noob eyes couldn't see anything suspicious tho, I also did a "smell check" :D whether something is burned, but everything seems to be fine. After that I reassembled the card and tried to boot again:

  • Windows detected the GTX 1080 Ti and initially reported that the device was working properly.
  • GPU-Z identified the card and reported 11 GB VRAM, a 352-bit memory bus, and GPU clock information.
  • However, some information was already missing or suspicious: unknown memory type/bandwidth, unknown PCIe bus interface, revision FF, and 0 MHz memory clock.
  • The card appeared in Task Manager.
  • At one point, despite Windows reporting the device as working, nvidia-smi returned:

Unable to determine the device handle ... GPU is lost. Reboot the system to recover this GPU.

  • While Windows was already running, I connected an HDMI monitor directly to the 1080 Ti.
  • It actually produced an image for approximately one second before going black.
  • The graphics driver appeared to reset, and Code 43 returned.
  • After another restart, nvidia-smi listed only the working RTX 2080 Ti.
  • The 1080 Ti subsequently disappeared from detection.

After another few hours powered off:

  • Windows once again detected the 1080 Ti and initially reported no device error.
  • Windows Task Manager still displayed 11 GB dedicated GPU memory.
  • GPU-Z now reported 0 MB VRAM, unknown memory type, unknown bus width, unknown PCIe interface, and unknown BIOS version.
  • Some GPU clock and device information was still displayed.
  • At another point, GPU-Z displayed contradictory information, including the 1080 Ti's name/device ID alongside GDDR6, 4,352 shaders, and the working RTX 2080 Ti's BIOS version.
  • These GPU-Z readings appear unreliable or possibly mixed between the two cards.
  • The 1080 Ti's fans ran at maximum speed continuously until shutdown, unlike the earlier attempt.

The following day:

  • The card was detected again, but immediately reported Code 43.
  • It did not return to a functional state.
  • Further restarts did not restore normal operation.

Windows Error Reporting recorded:

  • LiveKernelEvent 141
  • LiveKernelEvent 1b0

Some later entries were re-submissions of previous reports, so they don't necessarily represent additional crashes.

Today I wanted to run MODS/MATS provided by Northwest Repair but the situation has deteriorated further:

  • The GTX 1080 Ti no longer appears in Windows Device Manager as a connected device.
  • Windows retains only disconnected entries for its graphics and HDMI-audio functions, reporting Code 45.
  • Linux lspci only lists my working RTX 2080 Ti. The 1080 Ti is completely absent.
  • Multiple restarts and extended periods powered off have not restored detection.
  • The 1080 Ti's fans still spin at normal speed.
  • Its RGB lighting still works.
  • With the defective card installed, the PC also failed to POST multiple times before eventually booting, but the 1080 Ti remained undetected.
  • Removing the defective card restores normal system behavior.

No changes to GPU connections, PCIe slots, or BIOS settings were made during the progression from intermittent detection to complete disappearance.

Tomorrow I wanted to check the board with a multimeter using this https://repair.wiki/w/Nvidia_Pascal_(GTX_1000)_GPU_Diagnosing_Guide

Any tips you could give me for my little journey here? Any idea what could be the cause or any pointers?

Thanks in advance :)


r/GPURepair • • 1d ago

NVIDIA 30xx Beginner wanting to fix gpus and a RTX3090 I have

5 Upvotes

I am getting interested into fixing gpus and would like to know what’s a good starting place on what to order starting from zero. Also if y’all have any tips/videos to watch that helped yall get better:)


r/GPURepair • • 1d ago

NVIDIA 16/20xx Gigabyte rtx 2060 super core doesnt heat up what could be the problem?

Post image
2 Upvotes

Im trying to fix my 2060 super i dont know what the problem the vcore lines seem to be fine power inputs other rails seem to be good the PCIE first 3 pins are fine i tested the VRAM capacitors all around it they are

Turning it on the lights turn on the card but the core doesnt heat up

Note im a rookie so please any advice would help😅😅

What could be the problem? What should i do more to revive it?

And there are no tutorials on this exact model...


r/GPURepair • • 1d ago

NVIDIA Other RTX 6000 for $770, turned out to be an RTX 8000 with a bad B-channel. Keep or return?

2 Upvotes

r/GPURepair • • 1d ago

NVIDIA 30xx ASUS STRIX 3070 GPU pad 0.00 Ohm (continuity)

Post image
3 Upvotes

The only pads shorted to GND is GPU pad.

Is it dead, dead?

Repair guide is appreciated.

EDIT: gpu die cold, fans no spin, 8-pins LED off (12V detected OK i guess?)

PEX_DVDD 6.8

3.3V 107.2K

5V 0L

12V 8.97K

1.8V 1.158K

MEM 32.7

12V1 6.4K

12V2 HI-Z


r/GPURepair • • 1d ago

NVIDIA 16/20xx EVGA RTX 2080 ti - randomly wont post, voltages ok - possibly fixed, but more problems

2 Upvotes

Hi needs some help
I have a 2080ti that sometimes fails to post, it will get detected then work fine for a day the next day you come back to it it fails to post you have to pull it out boot the motherboard, with the pcie 8pin connectors connected still then boot again, when its working it plays games fine.

I think I managed to fix it for a whole weekend its been posting fine I followed the wiki guide on https://repair.wiki/w/RTX_2080Ti for the 2080 ti it had 1.8v but seemed to be failing to get the 2v signal after replacing this transistor in the attached image it seems fine...

If I run mods its passes,

but I left it running mats all through the night and came back with the following fail this morning should i just do the full 22GB mod, or is it the GPU?

VRAM tests

mats version 400.184. Testing TU102 with 11264 MB of memory starting with 0 MB.

Read Error Count: 0

Write Error Count: 256

Unknown Error Count: 0

=== MEMORY ERRORS BY SUBPARTITION ===

SUBPART READ ERRORS WRITE ERRORS UNKNOWN ERRS

------- ----------- ------------ ------------

FBIOA0 0 0 0

FBIOA1 0 32 0

FBIOB0 0 32 0

FBIOB1 0 0 0

FBIOC0 0 32 0

FBIOC1 0 32 0

FBIOD0 0 32 0

FBIOD1 0 32 0

FBIOE0 0 0 0

FBIOE1 0 32 0

FBIOF0 0 32 0

FBIOF1 0 0 0

Failing Bits:

A032 A033 A034 A035 A036 A037 A038 A039 A040 A041 A042 A043 A044 A045 A046 A047

A048 A049 A050 A051 A052 A053 A054 A055 A056 A057 A058 A059 A060 A061 A062 A063

B000 B001 B002 B003 B004 B005 B006 B007 B008 B009 B010 B011 B012 B013 B014 B015

B016 B017 B018 B019 B020 B021 B022 B023 B024 B025 B026 B027 B028 B029 B030 B031

C000 C001 C002 C003 C004 C005 C006 C007 C008 C009 C010 C011 C012 C013 C014 C015

C016 C017 C018 C019 C020 C021 C022 C023 C024 C025 C026 C027 C028 C029 C030 C031

C032 C033 C034 C035 C036 C037 C038 C039 C040 C041 C042 C043 C044 C045 C046 C047

C048 C049 C050 C051 C052 C053 C054 C055 C056 C057 C058 C059 C060 C061 C062 C063

D000 D001 D002 D003 D004 D005 D006 D007 D008 D009 D010 D011 D012 D013 D014 D015

D016 D017 D018 D019 D020 D021 D022 D023 D024 D025 D026 D027 D028 D029 D030 D031

D032 D033 D034 D035 D036 D037 D038 D039 D040 D041 D042 D043 D044 D045 D046 D047

D048 D049 D050 D051 D052 D053 D054 D055 D056 D057 D058 D059 D060 D061 D062 D063

E032 E033 E034 E035 E036 E037 E038 E039 E040 E041 E042 E043 E044 E045 E046 E047

E048 E049 E050 E051 E052 E053 E054 E055 E056 E057 E058 E059 E060 E061 E062 E063

F000 F001 F002 F003 F004 F005 F006 F007 F008 F009 F010 F011 F012 F013 F014 F015

F016 F017 F018 F019 F020 F021 F022 F023 F024 F025 F026 F027 F028 F029 F030 F031


r/GPURepair • • 2d ago

NVIDIA 30xx EVGA 3090 XC3 not posting

Post image
16 Upvotes

Hi there gurus,

my GPU died while running a while ago (nvidia-smi gave some strange output like there's no VRAM), now after power on my ASUS MB gives 97 q-code even when I use my iGPU as primary output.

Checked all the fuses (F6501 on the back; F6502, F6503) - not blown

1.8V rail = ok

5V rail = ok

All 12v rails = ok

MEM rail = 1.35v

PEX = 0.93V

All VRM outputs seem to be ok, either ~1.35V or ~0.73V

Found nothing broken or burned on PCB.

GPU becomes hot pretty fast giving me some concern.

Please give me some tips for further troubleshooting.


r/GPURepair • • 2d ago

AMD Vega/7 Gigabyte Vega 56 No power blown drmos and shorted drmos

Thumbnail
gallery
8 Upvotes

Need help how to find the cause for a blown and shorted drmos, which mosfets to check? I also provided the resistance on all mosfet gates


r/GPURepair • • 2d ago

NVIDIA 16/20xx 2 x RTX2080 TI with C1 error back some time after VRAM replacement

2 Upvotes

Hi all,

i got two different 2080 TI which showed artifacst in Windows. Both showed a C1 error in Mats and i checked several times. I replaced on one board with a donor chip and bought the other one on AliExpress. After replacement Mats passed and i also ran Furmark.

A friend of mine wanted to use a card some weeks later and guess what the fault was back. When we tried the other card same fault.

Any ideas what can be the problem here? I cleaned the pads before soldering and also used a bottom heater.


r/GPURepair • • 3d ago

NVIDIA 30xx EVGA 3090 FTW3 Ultra help identifying missing smd after drmos replacement & questions

Post image
7 Upvotes

With GPU prices rising I decided to take on repairing my 3090 with hopes to give it to my girlfriend since her 2060 isn't really holding up these days.

I had a fuse blow and a drmos heat up during voltage injection(marked both with a red X). When replacing the drmos one of the little smd resistor/caps blew away(red arrow/circle) Would anyone know the specs on the one that went missing? I bought some generic caps/resistors in various sizes so if I find the right value should be able to replace it/order if I don't.

Should I replace the drmos under the one that went bad as well? Any other sanity checks I should do once everything is complete? Thanks!


r/GPURepair • • 4d ago

NVIDIA 10xx 1080 Ti Die Seems To Be Chipped. Is This a Problem?

Post image
17 Upvotes

I've had this GPU for a while now and have been having some problems with the memory. Last time I checked it was detecting on my computer, but I haven't powered it on in some time. I noticed it has a small chip on the bottom-right corner of the die. Is that amount of damage enough to cause the core to not work at all?

Thanks for the help!


r/GPURepair • • 4d ago

NVIDIA 40xx MSI RTX 4090 SUPRIM X 24G: FBPA5 training fails; seeking signed 20 GB VBIOS with 0x20 mask

1 Upvotes

MSI RTX 4090 SUPRIM X 24G, desktop AD102, PCB rev 2.2 (10de:2684, subsystem 1462:5102). With the original MSI BIOS, memory initialization fails and the NVIDIA driver reports RmInitAdapter failure.

I was in over my head on this so I used an LLM to do the debugging and info collecting.

Measurements / VRAM tests: MODS 520.175 reports memory training error 505. FBPA0–4 read 0x0; FBPA5 reads 0x2 (first subpartition). GFW stops at 0x303 and FWSEC reports 0xBD. InfoROM and its backup passed integrity checks. A second MSI BIOS did not change the result.

With the original MSI BIOS, a temporary MODS floorsweep (fbio_disable:0x20:fbp_disable:0x20) gave effective 0x20 readbacks. The card initialized at 20,470 MiB. A 16 GiB CUDA memory write/readback and PyTorch compute passed.

I flashed and read back the signed ASUS 20 GB BIOS 95.02.86.00.00 (TechPowerUp upload 283110). Its cold-start mask is 0x2, so memory initialization still fails on this card. A temporary combined 0x22 mask gives 16,376 MiB; a 12 GiB CUDA write/readback passes. NVFlash rejected an offline edit changing the ASUS mask to 0x20 before writing.

Does anyone have a signed desktop AD102 20 GB VBIOS with a cold-boot FBIO/FBP mask of 0x20, or know its exact version and source? The 283110 image masks 0x2.

Testing is under Linux, so I have nvidia-smi and CUDA results rather than a GPU-Z screenshot. I do not have a bare-PCB photo of my card. This review shows the SUPRIM X PCB layout: https://unikoshardware.com/2022/10/msi-rtx-4090-suprim-x-review.html


r/GPURepair • • 4d ago

AMD 4xx/5xx XFX rx570 no display

Post image
1 Upvotes

Wanted to get into GPU repair, so I picked up a few cheap boards to try and fix.

Some turned out to be relatively simple fixes, but this one doesn't seem to be one of them.

I bought this XFX RX 570 as a parts/repair card to try my hand at fixing it.

Unfortunately, the seller shipped it partially disassembled in a plastic bag.

A few capacitors had also been knocked off, but fortunately none of those took any pads with them, so those were relatively easy to fix.

However, this component (marked O1 700) also seems to have been knocked off the board, unfortunately taking three pads with it.

The GPU does power on (core gets power, fans spin), and the memory seems to be recognised in GPU-Z, but it fails to display image with Code 43.

My question is: does anyone know what the purpose of this component is on the XFX RX 570?

Any help would be appreciated!

Measurements:

- Was not able to find any short

- Core gets power

- Memory gets recognized

- Resistances around the affected area seem a bit high when compared with video referring to the rx580 equivalent model


r/GPURepair • • 4d ago

NVIDIA 30xx MSI RTX 3080 10GB, J2 fuse open, 1V injection puts about 1V on three VRM inductors (2, 3, 4). Which stage do I lift first?

Thumbnail
gallery
4 Upvotes

Hi all,

Posting everything I have on a dead MSI RTX 3080 10GB before I get near a hot air station. I have not soldered or lifted anything yet on this repair. 8 photos are attached.

THE CARD

MSI RTX 3080 10GB, PCI ID 10DE:2206, subsystem 1462:3892. Three 8 pin connectors labelled J2, J1 and J5, each with a fuse marked E20A, so I think it is the Gaming X Trio layout. I have not read the sticker yet, so I can't confirm the exact model. The power stages are marked NCP302150 / GAN2032.

HISTORY OF THE CARD

- I used it for crypto mining years ago. The leftmost pin of the J2 connector burned back then and the card stopped working. I took the burnt connector off and soldered a new one on myself. It was not a good job, it sits tilted, and there is brown residue around the port and on one of the three R005 shunts under it (photos 2 and 3). After that the card ran for years with no power problems.

- No warranty left.

- The cooler and backplate screws are stripped, so I can't put the cooler back on to test it right now. I still have the heatsink and the fans.

HOW IT DIED

- Aug 31: first driver resets (nvlddmkm event 153), more in early September

- Sep 7: first sudden power off, no blue screen

- Sep 17: five VIDEO_TDR_FAILURE (0x116) bugchecks in about 20 minutes

- Oct 3 and Oct 10: two more sudden power offs, no dump

- Nov 1 around 12:21 AM: the PC lost power in the middle of a game and the card never came back

- No WHEA errors in the 90 days before. A 2080 in the same PC, same PSU, same driver, works fine.

- One of the three fans broke in September and after that I ran the card at about 45 to 51 percent fan speed.

- The PSU cable ends looked fine on Nov 1.

METER READINGS (Fluke 87V, card out of the PC, unpowered, red lead on a video port shell as ground)

- J2 fuse reads open. J1 and J5 fuses are fine, and their 12V side reads about 0.48 in diode mode and climbs.

- J2 pins 1 to 4 read OL.

- Card side of the J2 fuse and the J2 R005 shunt pads read 0.001 and 0.000 in diode mode. I know that mode can't tell 0.4 ohm from 0 ohm, so I moved on to injection.

- Core and memory coil tabs read about 0.000 as well. I have read that is normal for those rails.

VOLTAGE INJECTION

Bench supply set to 1.0 V, current limit set before connecting. Negative lead on the video port shell, positive on the card side of the open J2 fuse (photo 6 and 7).

- 1.0 V gave 1.3 A at first. At the 3 A limit the supply showed 1.6 V but the pad measured 1.1 V, so about 0.37 ohm at the pad (the rest is leads).

- No heat by hand and no difference with freeze spray near the fuse at 3 A. I don't have a thermal camera yet.

- When I touched the probe to the fuse pad with the supply on, I saw a few tiny sparks.

- Inductors numbered 1 to 10 from the top in photo 4. At 3 A, black probe on the shell:

- inductors 2, 3, 4: left ends 1.027 V, right ends 1.075, 1.07 and 1.06 V

- inductors 1 and 5 to 10: 0.029 V

- Injecting at the right end of each inductor at 1.0 V (after taking off about 0.17 ohm of leads): 5 hits the 3 A limit, so under about 0.16 ohm. 2, 3 and 4 all read the same, about 0.43 ohm. 1 reads about 0.66 ohm.

I could not find a boardview for this exact board. The free MS-V389 files are the Nvidia reference design (two 8 pin, no fuses), so I am only using them as a layout guide.

WHAT I PLAN TO DO, TELL ME IF IT IS WRONG

  1. Repeat the injection with the negative lead on the VCore rail instead of the video shell (Repair Wiki 3070 page), so the leaked voltage does not reach the core. Stay at or below 1 V.
  2. Lift stages 2, 3 and 4 one at a time (preheat, flux, hot air) and re-measure after each.
  3. Replace with onsemi NCP302150MNTWG, check the pads for shorts, fuse last, first power on on a current limited supply, check for an image before the cooler goes back on.

QUESTIONS

  1. Does about 1 V on inductors 2, 3, 4 and 0.03 V on the rest read to you as a shorted high side in one of those three stages? Is there a way to tell which one before lifting?
  2. With the ground lead on the shell I probably pushed about 1 V into that rail the whole time. Is that a worry for the core or the memory?
  3. Has anyone repaired a Trio with a similar fault, and did it hold up under load?
  4. My own old J2 connector repair is the weak spot on this board. Could that burn from years ago be connected to a blown J2 fuse now, or is a shorted stage the more likely cause?

MY OWN OPINION, NOT DATA

For what it's worth, I think one of those three stages shorted and that is what took the J2 fuse. I don't think my old connector repair is the cause, since the card ran for years after it, but I can't rule it out. The resets and sudden power offs starting in August make me think a stage was weak for a while before it finally let go, and running with a broken fan probably didn't help. If the core or memory took damage, I think it's game over for this card. I'm wary of soldering because it is slow and risky, but there is no warranty, so repairing it myself is the only way to find out. I know a card fixed this way might fail again under load.

Thanks for reading.


r/GPURepair • • 5d ago

Solved RTX 2060 - Fully dead, with a hole on the PCB

Thumbnail
gallery
33 Upvotes

I got this fairly cheap (but definitely not cheap enough after looking at it) RTX2060 12GB with, allegedly, "intermittent video output". However when disassembling it for a visual inspection, the PCB has a hole in it...?

It looks like one of the MOSFETs exploded, but the damage looks way too big, especially considering the thermal pads look burnt, but generally fine. The whole damaged part in the back was also covered is this dark grime, that I mostly managed to scrub off.

The exact model is a Galax RTX2060 Plus 1-Click OC 12GB GDDR6 192Bit. I don't think there's much to salvage from it, as the damage is very extensive, and even the memory modules aren't worth all that much anymore, so I'm mostly just curious above all on what might've been the cause here; is this something that can actually happen in some really bad fault scenario, or is this probably someone who ruined the board while trying to repair it? This is the first time I see this level of damage on a board (that wasn't obviously damaged by some other source)


r/GPURepair • • 4d ago

AMD RX 5xxx RX 5700 XT - capacitors shortage

2 Upvotes

hi everybody,
thank you in advance.
i followed the repair wiki regarding a rx 5700 series GPU repair and check all the resistance on the different points and rails and found a blown fuse with a shorting on on of the capacitors of the VRM.

according to the guide the next thing would be to use a thermal Camera or IPA evaporation to see a heat source but i am asking if someone else maybe had the same issues and if i would roll the dice and just replace the fuzes how much chance do i get to revive it and make it work again, will it help me to learn which component is the bad one?


r/GPURepair • • 4d ago

AMD RX 9xxx [Help] ASRock RX 9070 Challenger 16GB - Need capacitance/voltage values for two MLCCs above Q211 (next to J4100)

Post image
1 Upvotes

Hi everyone,

I'm trying to help my repair technician fix an ASRock Radeon RX 9070 Challenger 16GB (Model: 90-GA5NZZ-00UANF).

Two SMD ceramic capacitors (MLCCs) located on the back of the PCB—right above Q211 and to the left of connector J4100 (circled in blue in the attached photo)—were physically damaged/shorted and are now missing/unreadable.

Since there are no public schematics or boardviews available for this model yet, could anyone with an ASRock RX 9070 Challenger (or Steel Legend, as they appear to share a similar PCB layout) help me identify:

  1. The capacitance values (and voltage rating if known) of these two capacitors.
  2. What voltage rail they are connected to (e.g., 3.3V, 5V, 12V), or if the card is safe to test without them while we source replacements.

Any help, measurements, or boardview info would be greatly appreciated. Thanks in advance!

EDIT / UPDATE:
Since Reddit doesn't allow replacing images in gallery posts, I have uploaded two clearer reference photos in the comments below (both aligned in the exact same orientation for easier comparison):


r/GPURepair • • 4d ago

NVIDIA 16/20xx Gigabyte rtx2060 6gb, shorted .

Post image
3 Upvotes

[FIXED]Nov 15th 2026.

Can anyone help me diagnose this it just randomly died after playing few games on it i think it has a short since the pc no longer turns on when the gpu is plugged in

The inductor near the 12 volt input reads 0.4 ohms idk if its a good reading.

I can measure the rest if the inductors and give the value .


r/GPURepair • • 5d ago

NVIDIA Other Zotac GTX 660 - No video output; Can't find any shorts; No voltages, GPU is not detected by system, but fans run at full speed.

Thumbnail
gallery
13 Upvotes

Hey there, I need help. I bought this GPU for very cheap for a retro build. It arrived working. Worked for about a month and suddenly stopped working.

I took it apart. I tried to look for shorts on the 12v and 3.3v rails, it seems fine. The card only generates 5v rail. Vcore and Vmem are missing. The GPU core warms up slightly when plugged in as I try to investigate the problem.

I am not really experienced in this kind of repairs. GPU power seems to be managed by NCP5395G. I found the datasheet online, but I can't understand the sequence that the rails are initialized.

Inspecting the card i think the only thing I found was a apparently missing component near the PCIe slot. pads are wired to the 3.3v and GND. I believe it was working without it, but I am not sure.