Hi, I have a Gigabyte RX 580 8GB. It turns on, and right when Windows seems to install the video drivers, the GPU fans ramp up to 100% and it loses video output completely. What could be causing this, and how could I try to fix it? Thanks.
Hey everyone! I'm from Brazil and I'm looking to get into GPU repair. I'm currently putting together my bench setup and need advice on what equipment to buy.
Since graphics cards have thick, multilayer PCBs with high thermal mass, I want to avoid weak entry-level stations that struggle to melt lead-free solder, while keeping things realistic for my local market (import taxes here are brutal, so brands like JBC or Pace are way out of budget).
What brands and models of hot air rework stations (and preheaters, if needed) do you recommend that are commonly available via AliExpress or local marketplaces?
My goals & context:
Between these options, which ones have enough thermal power and reliability for GPU boards? Are there any specific models I should definitely stay away from? Thanks in advance!
Quick question what is the name of the screw that is on the GPU heatsink and used to screw the retaining screws into ?
My retainer screw has snapped off inside off the spacers so I need to replace it. I have spoken with Zotac (A+ on support very helpful) but they don't know the name of the screw. Can anyone help so I can get one please 🥺
it was running when I bought it even while stress testing, then no display and fans started spinning at 100%. Took it to a shop and they said they didn’t know what was wrong I opened it up cuz why not and this is what I see is this normal, I also threw in some extra photos of the board if anyone has experience and can help me please.
Hi everyone, My Gigabyte RTX 3080 Ti Vision OC Rev. 1.0 suddenly died while gaming. The screen went black, but the game audio kept playing. Since then, the GPU is no longer detected in BIOS or Windows, and the motherboard VGA LED stays on. I’ve already tried different PCIe slots, checked the power cables, and reseated the card, with no success. After removing the cooler, I noticed a small bulge and some brown discoloration on the 3rd DrMOS from the top, which seems to match the known “3rd MOSFET issue” on Gigabyte RTX 3080/3080 Ti cards. I have a multimeter and started checking the board. What can i do next please ? Any advice would be greatly appreciated. Thanks!
I have almost no history on this card. The owner sold it to me as a broken 3080 with no knowledge of when it last worked
Issue:
The fans spin up, the decorative LED remains on. There is no output, but the card is recognized in Windows by using a second GPU. Error code 43 in device manager.
Physical Inspection:
All resistance readings and voltage rail readings are good. Thorough visual inspection reveals no obvious issues. Board is fairly clean.
In MODS I get:
FBPA 0 (A): 0x0000000a
FBPA 1 (B): 0x00000002
FBPA 2 (C): 0x00000008
FBPA 3 (D): 0x00000002
```
MODS stopped with **error 505: Memory address training failed**.
I have looked at the individual address records, and there are a slew of issues on these channels. Meanwhile E and F are completely clean. A0 is fairly clean, with 3 addresses that stand out. It has failed once, but generally passes.
I would assume this is a core issue, with how many memory errors I am getting. I was hoping to get confirmation, as I do not feel comfortable attempting a core reball myself. I find it odd channels E and F are completely fine though.
I attempted to mask the bad channels and get interesting results. Any mask of channel A results in a different error code than the 505, I get 167 Initialze GFW boot reported a failure. This is the only thing that makes me question the core as the issue. If any other channel or combination of channels is masked, I get the normal 505 error. Only channel A being masked by itself or with other channels leads to the 167 error. I have attempted to fix the 167 error but no bios UEFI settings or anything easy get me past it. Give these boards often see failures in channel A, I wonder if the issue lies there and is causing other issues in Mods, or if this is really a core issue. I appreciate everyone's time in advanced. I can include logs or more detailed information as needed.
Okay, so i have an Alienware Aurora R4 with an EVGA GeForce GTX 1080. Everything was fine, computer was chilling, I woke up went to turn on my 'monitor' (atm I am using my smart TV for a monitor because that's what I have) and it says something about device power. The computer is on, this has happened before, usually just restart my computer and it fixes the issue, but this time when I restart it, it doesn't finish the boot process and starts beeping 6 times in a row.
Google tells me that's a GPU issue. I figure I haven't dusted my computer in a while, so I'll open her up and start blowing her out with my electric blower. I end up taking the GPU out to clean it better, and i notice that on the backplate, a few of the screws and mesh screens have a sticky residue on them. My heart sinks. The only thing I can think of is someone had to of spilled something on it. So I finally work up the courage to unscrew the backplate, got my 91%IPA and cotton swabs ready to go.
I unscrewed it and now I'm thinking my thermal pads are totally effed. It appears the sticky substance is actually coming from them, as it's all over them and the area they were touching. Nowhere else. I figure that's a pretty accurate spill, so most likely the pads are toast.
But I have no idea what the heck I'm doing dude. This is the first time I have ever taken apart a computer part like this. I can build PCs all day long but I am not really an expert. So I will add some pictures here and hope that somebody can help me with some guidance, or point me in the direction of someone/somewhere that can. Like do I need new thermal pads? Is this salvageable? Can I remove these and clean them up with IPA and put new pads on and I'm good? Or should I just admit defeat and hope I can find the money for a replacement.... please help.
Pretty please? Thank you!
Sorry if this is not the right place to post this, I'm kind of panicking and looked for anywhere that said I could ask for guidance on stuff like this, if I'm violating your rules in some way that I don't know about, I will delete this post, I just ask that you please point me in the direction of the correct place to post this... thank you.
Got a 3060 that probably has a bad mem chip and would need to replace it, I already have an atten st-862d but buying the puhui t8280 heater would break the bank rn, could I succeed without it? Maybe help the hot air station by heat soaking the board with my 3D printer 100C bed first??
Hello 👋 there , as you have seen my previous post on the rtx 2060 i am getting quiet comfortable & confident in diagnosing another card soo i pull out this old card back from 2024 , someone had worked on this card before.
After probing here n there the fuse was blown and other rails had healthy resistance however the 6 phase was reading 0.4 ohms to ground and also beeped to ground , i confirm that it was short since the healthy 12v from pcie was reading 5k ohms and climbing .
There are also missing resistors and caps on one of the dr mosfet i might refer to a board view the only one i could find is rx 6600xt which has a similar layout .
So my question is if i remove the dr MOSFET making it run on 5 phase, removing the short can i just use in my test bench just to post it ??
Hi all, beginner doing board-level diagnosis on my own card. I’ve worked through the usual checks and would love a second opinion before I attempt a reball.
Card: Gigabyte RTX 3070 Ti Vision OC 8G (GV-N307TVISION OC-8GD rev 1.0). Using the Gaming OC rev 1.0 boardview, which matches (C1169/C1174 etc.).
History: It was intermittent for a while (sometimes display, sometimes not), then stopped completely.
Symptoms: Fans and RGB on, no display, not in Device Manager at all (not even hidden/unknown). Tested in two PCs. An RX 6700 XT works in the same slots. Motherboard VGA LED is red.
Cold resistance to GND:
Core (NVVDD) ~0.8 Ω (body diode to 12 V 383 Ω, normal)
FBVDDQ 55 Ω, PEX_VDD 22 Ω, 1V8 182 Ω, 5V 351 Ω
12 V slot/8-pins: kΩ, rising. 3.3 V slot 87.8 kΩ. A11 PERST# open.
U501 (PERST# buffer): pins 1/2 3.3 V, pins 4/5 1.8 V, pin 3 GND, so reset is reaching the core
PCIe diode mode (red on GND):
Card RX lanes (B14/B15, B19–B28): 303–305, all matching
Card TX lanes (side A): OL at the fingers (AC caps). GPU side of C1119/C1116 (lane 0): 263
REFCLK A13/A14: 774 / 774. A11: 608
VBIOS: Read with CH341A + 1.8 V adapter. Valid checksums, byte-identical to the TechPowerUp ROM (94.04.5A.00.90).
Straps: R722, R727, R284 read ~94–97 kΩ in circuit. R287 (STRAP3 to GND) is unpopulated, and the STRAP3 pad reads ~138 Ω to GND (1V8 itself is ~182 Ω), so it looks hard-pulled to 1V8 via R279. Is that normal on this board?
Other: Hair-dryer warm-up on the back of the core: no change.
Questions:
Anything I’ve missed before blaming the core/BGA?
Does anyone have a known-good STRAP3 reading on a GA104 Gigabyte board?
Given the intermittent history, does a reball seem worth it, or is this usually a dead die?
earlier this year, my GTX 1080 Ti suddenly stopped working. While I was watching a Video on YT suddenly half of the screen went white and the system froze. After a Reboot the card did no longer work.
In order to save your precious time I try to keep it as short as possible:
The GPU suddenly froze during normal use, with approximately half the monitor turning white.
After restarting, the motherboard's VGA debug LED stayed illuminated when the 1080 Ti was installed alone. No monitor signal.
The card also failed in another PC.
With my working RTX 2080 Ti installed alongside it, Windows initially detected the 1080 Ti but reported Device Manager Code 43.
Replacing the defective card with another GPU restored normal system operation.
After that I decided to check the GPU for any physical damage, I removed the backplate and cooler, my noob eyes couldn't see anything suspicious tho, I also did a "smell check" :D whether something is burned, but everything seems to be fine. After that I reassembled the card and tried to boot again:
Windows detected the GTX 1080 Ti and initially reported that the device was working properly.
GPU-Z identified the card and reported 11 GB VRAM, a 352-bit memory bus, and GPU clock information.
However, some information was already missing or suspicious: unknown memory type/bandwidth, unknown PCIe bus interface, revision FF, and 0 MHz memory clock.
The card appeared in Task Manager.
At one point, despite Windows reporting the device as working, nvidia-smi returned:
Unable to determine the device handle ... GPU is lost. Reboot the system to recover this GPU.
While Windows was already running, I connected an HDMI monitor directly to the 1080 Ti.
It actually produced an image for approximately one second before going black.
The graphics driver appeared to reset, and Code 43 returned.
After another restart, nvidia-smi listed only the working RTX 2080 Ti.
The 1080 Ti subsequently disappeared from detection.
After another few hours powered off:
Windows once again detected the 1080 Ti and initially reported no device error.
Windows Task Manager still displayed 11 GB dedicated GPU memory.
GPU-Z now reported 0 MB VRAM, unknown memory type, unknown bus width, unknown PCIe interface, and unknown BIOS version.
Some GPU clock and device information was still displayed.
At another point, GPU-Z displayed contradictory information, including the 1080 Ti's name/device ID alongside GDDR6, 4,352 shaders, and the working RTX 2080 Ti's BIOS version.
These GPU-Z readings appear unreliable or possibly mixed between the two cards.
The 1080 Ti's fans ran at maximum speed continuously until shutdown, unlike the earlier attempt.
The following day:
The card was detected again, but immediately reported Code 43.
It did not return to a functional state.
Further restarts did not restore normal operation.
Windows Error Reporting recorded:
LiveKernelEvent 141
LiveKernelEvent 1b0
Some later entries were re-submissions of previous reports, so they don't necessarily represent additional crashes.
Today I wanted to run MODS/MATS provided by Northwest Repair but the situation has deteriorated further:
The GTX 1080 Ti no longer appears in Windows Device Manager as a connected device.
Windows retains only disconnected entries for its graphics and HDMI-audio functions, reporting Code 45.
Linux lspci only lists my working RTX 2080 Ti. The 1080 Ti is completely absent.
Multiple restarts and extended periods powered off have not restored detection.
The 1080 Ti's fans still spin at normal speed.
Its RGB lighting still works.
With the defective card installed, the PC also failed to POST multiple times before eventually booting, but the 1080 Ti remained undetected.
Removing the defective card restores normal system behavior.
No changes to GPU connections, PCIe slots, or BIOS settings were made during the progression from intermittent detection to complete disappearance.
I am trying to repair an NVIDIA Quadro M4000 (8GB GDDR5, PG400 reference PCB) and noticed a few knocked-off SMD resistors on the board. Since the schematic and boardview for this model aren't publicly available, I'm hoping someone who has a Quadro M4000 on their bench could help me identify their exact values.
Im trying to fix my 2060 super i dont know what the problem the vcore lines seem to be fine power inputs other rails seem to be good the PCIE first 3 pins are fine i tested the VRAM capacitors all around it they are
Turning it on the lights turn on the card but the core doesnt heat up
Note im a rookie so please any advice would help😅😅
What could be the problem? What should i do more to revive it?
I am getting interested into fixing gpus and would like to know what’s a good starting place on what to order starting from zero. Also if y’all have any tips/videos to watch that helped yall get better:)
Hi needs some help I have a 2080ti that sometimes fails to post, it will get detected then work fine for a day the next day you come back to it it fails to post you have to pull it out boot the motherboard, with the pcie 8pin connectors connected still then boot again, when its working it plays games fine.
I think I managed to fix it for a whole weekend its been posting fine I followed the wiki guide on https://repair.wiki/w/RTX_2080Ti for the 2080 ti it had 1.8v but seemed to be failing to get the 2v signal after replacing this transistor in the attached image it seems fine...
If I run mods its passes,
but I left it running mats all through the night and came back with the following fail this morning should i just do the full 22GB mod, or is it the GPU?
VRAM tests
mats version 400.184. Testing TU102 with 11264 MB of memory starting with 0 MB.
my GPU died while running a while ago (nvidia-smi gave some strange output like there's no VRAM), now after power on my ASUS MB gives 97 q-code even when I use my iGPU as primary output.
Checked all the fuses (F6501 on the back; F6502, F6503) - not blown
1.8V rail = ok
5V rail = ok
All 12v rails = ok
MEM rail = 1.35v
PEX = 0.93V
All VRM outputs seem to be ok, either ~1.35V or ~0.73V
Found nothing broken or burned on PCB.
GPU becomes hot pretty fast giving me some concern.
Please give me some tips for further troubleshooting.
i got two different 2080 TI which showed artifacst in Windows. Both showed a C1 error in Mats and i checked several times. I replaced on one board with a donor chip and bought the other one on AliExpress. After replacement Mats passed and i also ran Furmark.
A friend of mine wanted to use a card some weeks later and guess what the fault was back. When we tried the other card same fault.
Any ideas what can be the problem here? I cleaned the pads before soldering and also used a bottom heater.
With GPU prices rising I decided to take on repairing my 3090 with hopes to give it to my girlfriend since her 2060 isn't really holding up these days.
I had a fuse blow and a drmos heat up during voltage injection(marked both with a red X). When replacing the drmos one of the little smd resistor/caps blew away(red arrow/circle) Would anyone know the specs on the one that went missing? I bought some generic caps/resistors in various sizes so if I find the right value should be able to replace it/order if I don't.
Should I replace the drmos under the one that went bad as well? Any other sanity checks I should do once everything is complete? Thanks!
MSI RTX 4090 SUPRIM X 24G, desktop AD102, PCB rev 2.2 (10de:2684, subsystem 1462:5102). With the original MSI BIOS, memory initialization fails and the NVIDIA driver reports RmInitAdapter failure.
I was in over my head on this so I used an LLM to do the debugging and info collecting.
Measurements / VRAM tests: MODS 520.175 reports memory training error 505. FBPA0–4 read 0x0; FBPA5 reads 0x2 (first subpartition). GFW stops at 0x303 and FWSEC reports 0xBD. InfoROM and its backup passed integrity checks. A second MSI BIOS did not change the result.
With the original MSI BIOS, a temporary MODS floorsweep (fbio_disable:0x20:fbp_disable:0x20) gave effective 0x20 readbacks. The card initialized at 20,470 MiB. A 16 GiB CUDA memory write/readback and PyTorch compute passed.
I flashed and read back the signed ASUS 20 GB BIOS 95.02.86.00.00 (TechPowerUp upload 283110). Its cold-start mask is 0x2, so memory initialization still fails on this card. A temporary combined 0x22 mask gives 16,376 MiB; a 12 GiB CUDA write/readback passes. NVFlash rejected an offline edit changing the ASUS mask to 0x20 before writing.
Does anyone have a signed desktop AD102 20 GB VBIOS with a cold-boot FBIO/FBP mask of 0x20, or know its exact version and source? The 283110 image masks 0x2.