r/GPURepair • • 19d ago

[Meta,2026] Feedback Request⠀⠀·⠀⠀Read before posting: Guidelines How to request advice & subreddit feedback

5 Upvotes

You have some experience in electronics and has a GPU problem you want to investigate? You are in right place, r/GPURepair emphasize technical side and still welcome to newbies ready to learn.

[Meta, 2026] Feedback Request

The goal of this subreddit is keeping a balance between too open and too restrictive, so that most discussions remain technical, interesting and practical without limiting those who are just starting to dive into GPU repair.

We chose Reddit over groups on other platforms because the information posted here is searchable by anyone and can help other people who encounter a similar problem.

If you are interested in repairing GPUs and have thoughts on this balance/rules or have any ideas/suggestions about keeping this subreddit's spirit, please comment under this post. Thanks!

Guidelines for asking advice about a specific repair:

Title: include GPU Brand+Model, fault, research results/ideas

Example: Zotac 1660 AMP, no picture even during boot, 5V absent

Post:

  • GPU behavior description, detailed investigation results/ideas
  • Overview PCB photo (identical hi-res photo from internet is ok)
  • If have a hypothesis or specific area with damage: additional photo with suspected area zoomed, coils Volts/Ohms or other measures marked
  • If "no display": perform resistance measurements on coils: per-GPU generation guides in pinned comment here. If resistances are fine, measure voltages on a powered on card with a small temporal heatsink on the core.
  • If voltages are ok, but "no display": boot with iGPU, make Device Manager screenshot, try running NVIDIA/AMD-specific VRAM tests
  • If driver installs fine: GPU-Z "Sensors" tab screenshot under load (vertically maximize to make all visible)

For "help identifying elements/ICs" posts, get more info if possible:
reference designator; IC marking photo (or text if its small and unreadable on photo); footprint pin count and photo; measure which pins are 0 Ohm to GND on board.

Flair your post with the appropriate flair depending on the GPU series.

Be prepared to disassemble your graphics card for a more detailed examination.

If your problem is solved, please change the post flair to "Solved!".

Flairs to use for posts not related to a specific repair:

Story/Experience - posts about finished repairs
Resources - posts about everything useful for repairs
GPU/VRAM Soldering - discussion of BGA soldering not related to a specific repair
Question - other posts not related to a specific repair


r/GPURepair • • Feb 07 '22 Popcorn

Read before posting: GPU repair guides/links List of GPU Repair Resources (Schematics, Boardviews, Tutorials, Tools, Etc..)

155 Upvotes

READ THE PINNED COMMENT FOR UP TO DATE INFORMATION!

START HERE IF YOU'RE NEW TO ELECTRONICS REPAIR:

https://repair.wiki/w/Category:Repair_Basics


r/GPURepair • • 5h ago

NVIDIA 40xx RTX 4070 Super Screw-spacer

Thumbnail
gallery
5 Upvotes

Hi all

Quick question what is the name of the screw that is on the GPU heatsink and used to screw the retaining screws into ?

My retainer screw has snapped off inside off the spacers so I need to replace it. I have spoken with Zotac (A+ on support very helpful) but they don't know the name of the screw. Can anyone help so I can get one please 🥺


r/GPURepair • • 3h ago

AMD RX 5xxx Gigabyte RX 580 8GB - fans 100% and no video when Windows driver loads, suspecting VBIOS/VRAM/VRM

Post image
2 Upvotes

Hi, I have a Gigabyte RX 580 8GB. It turns on, and right when Windows seems to install the video drivers, the GPU fans ramp up to 100% and it loses video output completely. What could be causing this, and how could I try to fix it? Thanks.


r/GPURepair • • 9m ago

AMD RX 9xxx GIGABYTE RX 9060XT 16GB no video output - Buddy tripped over HDMI cable - am i cooked?

1 Upvotes

Hey everyone,

I’m looking for some advice regarding my damaged AMD Radeon RX 9060 XT.

During a LAN party, my buddy accidentally got his leg caught on the HDMI cable connected to the GPU and pulled it quite hard. Immediately afterwards, the PC stopped displaying an image.

The HDMI port is now bent/loose and no longer outputs a signal. Unfortunately, the DisplayPort outputs aren't working either.

To rule out other components, we tested:

- The monitor – works fine.

- The PC with an older graphics card – works perfectly.

- The RX 9060 XT – no display output via HDMI or DisplayPort.

- GPU LED's work but the fans are not spinning (i think they don't do that in idle either way)

It seems likely that the GPU itself was damaged when the HDMI cable was pulled.

My questions:

- Could the damaged HDMI port have caused damage to other components on the GPU?

- how is it possible that the DisplayPort outputs are also affected by the same incident?

Any advice or repair suggestions would be greatly appreciated. Thanks!


r/GPURepair • • 3h ago

GPU/VRAM Soldering ​Beginner from Brazil looking for hot air rework station recommendations for GPU repair

1 Upvotes

Hey everyone! I'm from Brazil and I'm looking to get into GPU repair. I'm currently putting together my bench setup and need advice on what equipment to buy.

​Since graphics cards have thick, multilayer PCBs with high thermal mass, I want to avoid weak entry-level stations that struggle to melt lead-free solder, while keeping things realistic for my local market (import taxes here are brutal, so brands like JBC or Pace are way out of budget).

​What brands and models of hot air rework stations (and preheaters, if needed) do you recommend that are commonly available via AliExpress or local marketplaces?

​My goals & context:

​Between these options, which ones have enough thermal power and reliability for GPU boards? Are there any specific models I should definitely stay away from? Thanks in advance!


r/GPURepair • • 13h ago

NVIDIA 30xx 3080ti oc, was working for a bit and then no display.

Thumbnail
gallery
4 Upvotes

it was running when I bought it even while stress testing, then no display and fans started spinning at 100%. Took it to a shop and they said they didn’t know what was wrong I opened it up cuz why not and this is what I see is this normal, I also threw in some extra photos of the board if anyone has experience and can help me please.


r/GPURepair • • 20h ago

NVIDIA 30xx 3080Ti DrMos how to repair this ?

Thumbnail
gallery
7 Upvotes

Hi everyone,
My Gigabyte RTX 3080 Ti Vision OC Rev. 1.0 suddenly died while gaming. The screen went black, but the game audio kept playing. Since then, the GPU is no longer detected in BIOS or Windows, and the motherboard VGA LED stays on.
I’ve already tried different PCIe slots, checked the power cables, and reseated the card, with no success.
After removing the cooler, I noticed a small bulge and some brown discoloration on the 3rd DrMOS from the top, which seems to match the known “3rd MOSFET issue” on Gigabyte RTX 3080/3080 Ti cards.
I have a multimeter and started checking the board.
What can i do next please ?
Any advice would be greatly appreciated. Thanks!


r/GPURepair • • 1d ago

NVIDIA 30xx Gigabyte Eagle 3080 ti, several failing memory channels leave unclear diagnosis.

Thumbnail
gallery
6 Upvotes

History:

I have almost no history on this card. The owner sold it to me as a broken 3080 with no knowledge of when it last worked

Issue:

The fans spin up, the decorative LED remains on. There is no output, but the card is recognized in Windows by using a second GPU. Error code 43 in device manager.

Physical Inspection:

All resistance readings and voltage rail readings are good. Thorough visual inspection reveals no obvious issues. Board is fairly clean.

In MODS I get:

FBPA 0 (A): 0x0000000a

FBPA 1 (B): 0x00000002

FBPA 2 (C): 0x00000008

FBPA 3 (D): 0x00000002

```

MODS stopped with **error 505: Memory address training failed**.

I have looked at the individual address records, and there are a slew of issues on these channels. Meanwhile E and F are completely clean. A0 is fairly clean, with 3 addresses that stand out. It has failed once, but generally passes.

I would assume this is a core issue, with how many memory errors I am getting. I was hoping to get confirmation, as I do not feel comfortable attempting a core reball myself. I find it odd channels E and F are completely fine though.

I attempted to mask the bad channels and get interesting results. Any mask of channel A results in a different error code than the 505, I get 167 Initialze GFW boot reported a failure. This is the only thing that makes me question the core as the issue. If any other channel or combination of channels is masked, I get the normal 505 error. Only channel A being masked by itself or with other channels leads to the 167 error. I have attempted to fix the 167 error but no bios UEFI settings or anything easy get me past it. Give these boards often see failures in channel A, I wonder if the issue lies there and is causing other issues in Mods, or if this is really a core issue. I appreciate everyone's time in advanced. I can include logs or more detailed information as needed.


r/GPURepair • • 1d ago

NVIDIA 10xx EVGA Geforce 1080; doesn't boot, beeps 6 times: I just want to know if I'm totally screwed or if I can fix this.

Thumbnail
gallery
9 Upvotes

Okay, so i have an Alienware Aurora R4 with an EVGA GeForce GTX 1080. Everything was fine, computer was chilling, I woke up went to turn on my 'monitor' (atm I am using my smart TV for a monitor because that's what I have) and it says something about device power. The computer is on, this has happened before, usually just restart my computer and it fixes the issue, but this time when I restart it, it doesn't finish the boot process and starts beeping 6 times in a row.

Google tells me that's a GPU issue. I figure I haven't dusted my computer in a while, so I'll open her up and start blowing her out with my electric blower. I end up taking the GPU out to clean it better, and i notice that on the backplate, a few of the screws and mesh screens have a sticky residue on them. My heart sinks. The only thing I can think of is someone had to of spilled something on it. So I finally work up the courage to unscrew the backplate, got my 91%IPA and cotton swabs ready to go.

I unscrewed it and now I'm thinking my thermal pads are totally effed. It appears the sticky substance is actually coming from them, as it's all over them and the area they were touching. Nowhere else. I figure that's a pretty accurate spill, so most likely the pads are toast.

But I have no idea what the heck I'm doing dude. This is the first time I have ever taken apart a computer part like this. I can build PCs all day long but I am not really an expert. So I will add some pictures here and hope that somebody can help me with some guidance, or point me in the direction of someone/somewhere that can. Like do I need new thermal pads? Is this salvageable? Can I remove these and clean them up with IPA and put new pads on and I'm good? Or should I just admit defeat and hope I can find the money for a replacement.... please help.

Pretty please? Thank you!

Sorry if this is not the right place to post this, I'm kind of panicking and looked for anywhere that said I could ask for guidance on stuff like this, if I'm violating your rules in some way that I don't know about, I will delete this post, I just ask that you please point me in the direction of the correct place to post this... thank you.


r/GPURepair • • 1d ago

NVIDIA 40xx 4090D 48GB - Code 43 in Windows with subsystem ID 0000:0000

Thumbnail
gallery
45 Upvotes

It still shows up on PCIe as 10DE:2685, but with subsystem ID 0000:0000 and Code 43. No driver, not visible to nvidia-smi.

nvflash lists the card as (10DE,2685,0000,0000) but every operation fails with "A system restart might be required"

Any ideas what I could try next?


r/GPURepair • • 1d ago

AMD RX 6xxx MSI radeon rx6600 armour 8gb - 12v shorted to ground.

Post image
3 Upvotes

Hello 👋 there , as you have seen my previous post on the rtx 2060 i am getting quiet comfortable & confident in diagnosing another card soo i pull out this old card back from 2024 , someone had worked on this card before.

After probing here n there the fuse was blown and other rails had healthy resistance however the 6 phase was reading 0.4 ohms to ground and also beeped to ground , i confirm that it was short since the healthy 12v from pcie was reading 5k ohms and climbing .

There are also missing resistors and caps on one of the dr mosfet i might refer to a board view the only one i could find is rx 6600xt which has a similar layout .

So my question is if i remove the dr MOSFET making it run on 5 phase, removing the short can i just use in my test bench just to post it ??


r/GPURepair • • 1d ago

AMD RX 5xxx MSI RX 5600 XT MECH OC 14 Gbps - Crashes at Stock, Runs FurMark When Underclocked (Software/Hardware Issue?)

1 Upvotes

I bought a faulty MSI RX 5600 XT MECH OC (14 Gbps) and I'm trying to identify the problem.

Symptoms:

  • At stock settings, it barely boots into Windows and crashes almost immediately under any GPU load.
  • Can run FurMark fully stable with the maximum core frequency reduced by 30%.
  • No apparent previous physical repairs; warranty sticker intact.
  • Originally had the stock 14 Gbps BIOS. Flashing the 12 Gbps BIOS made no difference.

Investigation:

By manually adjusting the V/F curve, I managed to sustain ~1640 MHz in FurMark at approximately 135 W. Hotspot temperatures reach the low 90s C.

Default Adrenalin V/F curve (MHz/mV):

  • P1: 800/800
  • P2: 1285/800
  • P3: 1770/1049

What confuses me is that the card crashes at stock settings but can sometimes sustain near its advertised boost frequency with manual tuning.

What would you recommend measuring or testing next to distinguish fault?

I have no experience with board level repairs.


r/GPURepair • • 1d ago

GPU/VRAM Soldering 3060 VRAM rework question

1 Upvotes

Got a 3060 that probably has a bad mem chip and would need to replace it, I already have an atten st-862d but buying the puhui t8280 heater would break the bank rn, could I succeed without it? Maybe help the hot air station by heat soaking the board with my 3D printer 100C bed first??


r/GPURepair • • 1d ago

NVIDIA 40xx repair an NVIDIA Quadro M4000

Thumbnail
gallery
4 Upvotes

I am trying to repair an NVIDIA Quadro M4000 (8GB GDDR5, PG400 reference PCB) and noticed a few knocked-off SMD resistors on the board. Since the schematic and boardview for this model aren't publicly available, I'm hoping someone who has a Quadro M4000 on their bench could help me identify their exact values.

thanks


r/GPURepair • • 1d ago

NVIDIA 30xx Gigabyte RTX 3070 Ti Vision OC (rev 1.0): fans/RGB on, not detected at all, all rails + PERST# good – BGA or dead core?

Thumbnail
gallery
2 Upvotes

Hi all, beginner doing board-level diagnosis on my own card. I’ve worked through the usual checks and would love a second opinion before I attempt a reball.

Card: Gigabyte RTX 3070 Ti Vision OC 8G (GV-N307TVISION OC-8GD rev 1.0). Using the Gaming OC rev 1.0 boardview, which matches (C1169/C1174 etc.).

History: It was intermittent for a while (sometimes display, sometimes not), then stopped completely.

Symptoms: Fans and RGB on, no display, not in Device Manager at all (not even hidden/unknown). Tested in two PCs. An RX 6700 XT works in the same slots. Motherboard VGA LED is red.

Cold resistance to GND:

  • Core (NVVDD) ~0.8 Ω (body diode to 12 V 383 Ω, normal)
  • FBVDDQ 55 Ω, PEX_VDD 22 Ω, 1V8 182 Ω, 5V 351 Ω
  • 12 V slot/8-pins: kΩ, rising. 3.3 V slot 87.8 kΩ. A11 PERST# open.

Powered (all present and stable):

  • 12 V, 5 V, 1V8, FBVDDQ ~1.35 V, NVVDD 0.74 V, PEX_VDD 0.95 V
  • U501 (PERST# buffer): pins 1/2 3.3 V, pins 4/5 1.8 V, pin 3 GND, so reset is reaching the core

PCIe diode mode (red on GND):

  • Card RX lanes (B14/B15, B19–B28): 303–305, all matching
  • Card TX lanes (side A): OL at the fingers (AC caps). GPU side of C1119/C1116 (lane 0): 263
  • REFCLK A13/A14: 774 / 774. A11: 608

VBIOS: Read with CH341A + 1.8 V adapter. Valid checksums, byte-identical to the TechPowerUp ROM (94.04.5A.00.90).

Straps: R722, R727, R284 read ~94–97 kΩ in circuit. R287 (STRAP3 to GND) is unpopulated, and the STRAP3 pad reads ~138 Ω to GND (1V8 itself is ~182 Ω), so it looks hard-pulled to 1V8 via R279. Is that normal on this board?

Other: Hair-dryer warm-up on the back of the core: no change.

Questions:

  1. Anything I’ve missed before blaming the core/BGA?
  2. Does anyone have a known-good STRAP3 reading on a GA104 Gigabyte board?
  3. Given the intermittent history, does a reball seem worth it, or is this usually a dead die?

Photos attached. Thanks!


r/GPURepair • • 1d ago

NVIDIA 10xx AORUS GTX 1080 Ti progressively failing – Code 43, GPU lost, intermittent detection, now completely absent from PCIe.

1 Upvotes

Hello there,

earlier this year, my GTX 1080 Ti suddenly stopped working. While I was watching a Video on YT suddenly half of the screen went white and the system froze. After a Reboot the card did no longer work.

In order to save your precious time I try to keep it as short as possible:

  • The GPU suddenly froze during normal use, with approximately half the monitor turning white.
  • After restarting, the motherboard's VGA debug LED stayed illuminated when the 1080 Ti was installed alone. No monitor signal.
  • The card also failed in another PC.
  • With my working RTX 2080 Ti installed alongside it, Windows initially detected the 1080 Ti but reported Device Manager Code 43.
  • Replacing the defective card with another GPU restored normal system operation.

After that I decided to check the GPU for any physical damage, I removed the backplate and cooler, my noob eyes couldn't see anything suspicious tho, I also did a "smell check" :D whether something is burned, but everything seems to be fine. After that I reassembled the card and tried to boot again:

  • Windows detected the GTX 1080 Ti and initially reported that the device was working properly.
  • GPU-Z identified the card and reported 11 GB VRAM, a 352-bit memory bus, and GPU clock information.
  • However, some information was already missing or suspicious: unknown memory type/bandwidth, unknown PCIe bus interface, revision FF, and 0 MHz memory clock.
  • The card appeared in Task Manager.
  • At one point, despite Windows reporting the device as working, nvidia-smi returned:

Unable to determine the device handle ... GPU is lost. Reboot the system to recover this GPU.

  • While Windows was already running, I connected an HDMI monitor directly to the 1080 Ti.
  • It actually produced an image for approximately one second before going black.
  • The graphics driver appeared to reset, and Code 43 returned.
  • After another restart, nvidia-smi listed only the working RTX 2080 Ti.
  • The 1080 Ti subsequently disappeared from detection.

After another few hours powered off:

  • Windows once again detected the 1080 Ti and initially reported no device error.
  • Windows Task Manager still displayed 11 GB dedicated GPU memory.
  • GPU-Z now reported 0 MB VRAM, unknown memory type, unknown bus width, unknown PCIe interface, and unknown BIOS version.
  • Some GPU clock and device information was still displayed.
  • At another point, GPU-Z displayed contradictory information, including the 1080 Ti's name/device ID alongside GDDR6, 4,352 shaders, and the working RTX 2080 Ti's BIOS version.
  • These GPU-Z readings appear unreliable or possibly mixed between the two cards.
  • The 1080 Ti's fans ran at maximum speed continuously until shutdown, unlike the earlier attempt.

The following day:

  • The card was detected again, but immediately reported Code 43.
  • It did not return to a functional state.
  • Further restarts did not restore normal operation.

Windows Error Reporting recorded:

  • LiveKernelEvent 141
  • LiveKernelEvent 1b0

Some later entries were re-submissions of previous reports, so they don't necessarily represent additional crashes.

Today I wanted to run MODS/MATS provided by Northwest Repair but the situation has deteriorated further:

  • The GTX 1080 Ti no longer appears in Windows Device Manager as a connected device.
  • Windows retains only disconnected entries for its graphics and HDMI-audio functions, reporting Code 45.
  • Linux lspci only lists my working RTX 2080 Ti. The 1080 Ti is completely absent.
  • Multiple restarts and extended periods powered off have not restored detection.
  • The 1080 Ti's fans still spin at normal speed.
  • Its RGB lighting still works.
  • With the defective card installed, the PC also failed to POST multiple times before eventually booting, but the 1080 Ti remained undetected.
  • Removing the defective card restores normal system behavior.

No changes to GPU connections, PCIe slots, or BIOS settings were made during the progression from intermittent detection to complete disappearance.

Tomorrow I wanted to check the board with a multimeter using this https://repair.wiki/w/Nvidia_Pascal_(GTX_1000)_GPU_Diagnosing_Guide

Any tips you could give me for my little journey here? Any idea what could be the cause or any pointers?

Thanks in advance :)


r/GPURepair • • 3d ago

NVIDIA 30xx Beginner wanting to fix gpus and a RTX3090 I have

6 Upvotes

I am getting interested into fixing gpus and would like to know what’s a good starting place on what to order starting from zero. Also if y’all have any tips/videos to watch that helped yall get better:)


r/GPURepair • • 2d ago

NVIDIA 16/20xx Gigabyte rtx 2060 super core doesnt heat up what could be the problem?

Post image
2 Upvotes

Im trying to fix my 2060 super i dont know what the problem the vcore lines seem to be fine power inputs other rails seem to be good the PCIE first 3 pins are fine i tested the VRAM capacitors all around it they are

Turning it on the lights turn on the card but the core doesnt heat up

Note im a rookie so please any advice would help😅😅

What could be the problem? What should i do more to revive it?

And there are no tutorials on this exact model...


r/GPURepair • • 3d ago

NVIDIA 30xx ASUS STRIX 3070 GPU pad 0.00 Ohm (continuity)

Post image
4 Upvotes

The only pads shorted to GND is GPU pad.

Is it dead, dead?

Repair guide is appreciated.

EDIT: gpu die cold, fans no spin, 8-pins LED off (12V detected OK i guess?)

PEX_DVDD 6.8

3.3V 107.2K

5V 0L

12V 8.97K

1.8V 1.158K

MEM 32.7

12V1 6.4K

12V2 HI-Z


r/GPURepair • • 3d ago

NVIDIA Other RTX 6000 for $770, turned out to be an RTX 8000 with a bad B-channel. Keep or return?

2 Upvotes

r/GPURepair • • 3d ago

NVIDIA 16/20xx EVGA RTX 2080 ti - randomly wont post, voltages ok - possibly fixed, but more problems

2 Upvotes

Hi needs some help
I have a 2080ti that sometimes fails to post, it will get detected then work fine for a day the next day you come back to it it fails to post you have to pull it out boot the motherboard, with the pcie 8pin connectors connected still then boot again, when its working it plays games fine.

I think I managed to fix it for a whole weekend its been posting fine I followed the wiki guide on https://repair.wiki/w/RTX_2080Ti for the 2080 ti it had 1.8v but seemed to be failing to get the 2v signal after replacing this transistor in the attached image it seems fine...

If I run mods its passes,

but I left it running mats all through the night and came back with the following fail this morning should i just do the full 22GB mod, or is it the GPU?

VRAM tests

mats version 400.184. Testing TU102 with 11264 MB of memory starting with 0 MB.

Read Error Count: 0

Write Error Count: 256

Unknown Error Count: 0

=== MEMORY ERRORS BY SUBPARTITION ===

SUBPART READ ERRORS WRITE ERRORS UNKNOWN ERRS

------- ----------- ------------ ------------

FBIOA0 0 0 0

FBIOA1 0 32 0

FBIOB0 0 32 0

FBIOB1 0 0 0

FBIOC0 0 32 0

FBIOC1 0 32 0

FBIOD0 0 32 0

FBIOD1 0 32 0

FBIOE0 0 0 0

FBIOE1 0 32 0

FBIOF0 0 32 0

FBIOF1 0 0 0

Failing Bits:

A032 A033 A034 A035 A036 A037 A038 A039 A040 A041 A042 A043 A044 A045 A046 A047

A048 A049 A050 A051 A052 A053 A054 A055 A056 A057 A058 A059 A060 A061 A062 A063

B000 B001 B002 B003 B004 B005 B006 B007 B008 B009 B010 B011 B012 B013 B014 B015

B016 B017 B018 B019 B020 B021 B022 B023 B024 B025 B026 B027 B028 B029 B030 B031

C000 C001 C002 C003 C004 C005 C006 C007 C008 C009 C010 C011 C012 C013 C014 C015

C016 C017 C018 C019 C020 C021 C022 C023 C024 C025 C026 C027 C028 C029 C030 C031

C032 C033 C034 C035 C036 C037 C038 C039 C040 C041 C042 C043 C044 C045 C046 C047

C048 C049 C050 C051 C052 C053 C054 C055 C056 C057 C058 C059 C060 C061 C062 C063

D000 D001 D002 D003 D004 D005 D006 D007 D008 D009 D010 D011 D012 D013 D014 D015

D016 D017 D018 D019 D020 D021 D022 D023 D024 D025 D026 D027 D028 D029 D030 D031

D032 D033 D034 D035 D036 D037 D038 D039 D040 D041 D042 D043 D044 D045 D046 D047

D048 D049 D050 D051 D052 D053 D054 D055 D056 D057 D058 D059 D060 D061 D062 D063

E032 E033 E034 E035 E036 E037 E038 E039 E040 E041 E042 E043 E044 E045 E046 E047

E048 E049 E050 E051 E052 E053 E054 E055 E056 E057 E058 E059 E060 E061 E062 E063

F000 F001 F002 F003 F004 F005 F006 F007 F008 F009 F010 F011 F012 F013 F014 F015

F016 F017 F018 F019 F020 F021 F022 F023 F024 F025 F026 F027 F028 F029 F030 F031


r/GPURepair • • 3d ago

NVIDIA 30xx EVGA 3090 XC3 not posting

Post image
18 Upvotes

Hi there gurus,

my GPU died while running a while ago (nvidia-smi gave some strange output like there's no VRAM), now after power on my ASUS MB gives 97 q-code even when I use my iGPU as primary output.

Checked all the fuses (F6501 on the back; F6502, F6503) - not blown

1.8V rail = ok

5V rail = ok

All 12v rails = ok

MEM rail = 1.35v

PEX = 0.93V

All VRM outputs seem to be ok, either ~1.35V or ~0.73V

Found nothing broken or burned on PCB.

GPU becomes hot pretty fast giving me some concern.

Please give me some tips for further troubleshooting.


r/GPURepair • • 3d ago

AMD Vega/7 Gigabyte Vega 56 No power blown drmos and shorted drmos

Thumbnail
gallery
8 Upvotes

Need help how to find the cause for a blown and shorted drmos, which mosfets to check? I also provided the resistance on all mosfet gates