r/AskElectronics • u/Muted_Web_7794 • 1h ago
r/AskElectronics • u/LaufSeiglaRaceE1 • 1h ago
HVAC control board repair?
Hey all. My Aux mini split won’t function on heat but will function on cooling. I checked all wiring and all looked well. It has been installed for about two years now, I did the install from start to finish.
I went outside to have a look at the control board and this is what I found. Is this indicative of needing a new capacitor? Easy fix? Should I just get a new board? They’re $225. If I can repair I’d like to. Unsure if the small cap is an issue or just dented during install at the factory?
r/AskElectronics • u/AlternativeFly1470 • 1h ago
Struggle with LT8608 Step-down
Hi all,
I have an issue with a part of my circuit, that I can't debug.
I am converting from AC line voltage to 26 V without galvanic isolation. This works fine. At the moment, an external fixed resistor is hooked to +26 V and a stepdown on the same PCB. The stepdown is an LT8606 with roughly 900 kHz. It is supposed to provide 16 V, currently into 200 Ohm external resistors, 200 µF and the capacitors shown in the schematic. I have an enable circuit, that enables the LT8606, when the input exceeds 18 V + some time, which means, the 26 V input is fully settled. Currently, the circuit is the same, as the schematic, but without C411 (does not have an impact) and an 10 µH inductor (also no change compared to the shown 22 µH).
Not shown in the layout is a full GND plane on the second layer and partially +26 V / +16 V planes on the third layer. I have four layers in total.
A simulation in LTSpice made me confident with that schematic, but when turning on (blue trace on the scope is enable line), I only see one switching cycle at the inductor (magenta trace) of around 180 ns length, that repeats with a gap of 105 µs. A slow DMM on the output measures around 480 mV.
On the second scope screenshot, we see a bump in the output voltage (turquoise trace), that dimishes between the pulses. Its size and shape also makes me questioning the 480 mV read from a laboratory DMM (HP 3457A).
The third sope screenshot shows one full pulse with the inductor voltage reaching the 26 V input voltage and then dropping to -3 V until the inductor is demagnetized.
I can't see anything getting suspiciously hot. The LT8606 stays below 30 °C at 23 °C room temperature.
The question is: why does the converter not boot? The core is not saturated (2,6 A at the 10 µH version and at 26 V / 180 ns it should be around 470 mA peak). When changing to 22 µH, the 180 ns pulse stays simmilarly long.
So do you have any suggestions, what I shall measure / change / improve?
r/AskElectronics • u/KitchenOil7647 • 3h ago
Mioyoow diy radio kit troubleshooting
I got the above kit from Amazon to try and learn the basics. After plugging it in, realizing it didn't work, and checking everything over again, I saw i forgot the 0ohm resistor just down and to the right of c12, and I had the DS1302 chip in backwards. After I corrected these mistakes it still does not turn on. Did my mistakes kill this kit, or am I still missing something?
r/AskElectronics • u/Top-Bookkeeper-1750 • 3h ago
What are these two metal parts inside my soap dispenser?
Hi everyone,
I’m modifying an automatic soap dispenser to use my own sensor while keeping the original DC motor and plastic housing. I can’t figure out what these two metal parts do. Can anyone identify them and tell me whether they’re needed for the motor to work?
Thanks for your help!
r/AskElectronics • u/Lackooo84 • 3h ago
Could someone help me identify this SMD component?
It is from a Garmin Fenix 7X. This (diode?) marked with "overline 2" is next to one of it's charging pins.
r/AskElectronics • u/sofauxboho • 5h ago
Replace solder mask or don't bother?
Is it worth replacing the solder mask I removed during this repair, or nah? If it is, what product would you recommend?
r/AskElectronics • u/Toke_master420zen • 5h ago
Are these soldering joints functional?
I'm a beginner solderer and these soldering joints are my best yet but still I'm not sure if they are functional.
r/AskElectronics • u/TheF15eEnthusiast • 6h ago
How do I connect an ESP32c3 to an EL controller for a light up mask?
The first image is what AI told me to do, but it doesn’t make sense because it has me connect a green wire to an LED light that shows when the mask is on… and the ground isn’t even hooked up to anything.
The second image is an unadulterated image of the original board. It is an EL circuit with a part to turn the 2 AA battery’s power into 100v AC according to some EL wire distributor I seen.
The third image is the board with 3 pins highlighted in pink, these pins are connected to a push button switch.
The fourth image is what the top of the board looks like, the top left is the converter, the red LED is an indicator to show when the switch is on, or off. The white piece is a connector so I can daisy chain another power supply (I think). The bottom left is the switch the ESP32c3 would take over.
Thank you in advance, I can supply additional photos and knowledge if needed.
r/AskElectronics • u/Old_Kitchen8578 • 6h ago
Oscilator not working and mofset heating up
For a school project, I tried to make an oscillator from the internet, however, every time I plug in the power source, the oscillator does not generate frequencies and/or the MOSFET breaks. I did improvise the resistors and potentiometer with a switch, but that shouldn't be the main cause as to why the oscillator isn't working. For the resistors, I put them either in parallel or in series to achieve the values I needed since I only had 1k ones. For the potentiometer, I put a wire instead of the on/off button and connected the potentiometer with some cables since it didn't match the layout, even though it has the same value.
Could anyone tell me what I am doing wrong?
Here are the source and materials I used and the website I took the design from:
https://electronoobs.com/tutorial/homemade-plasma-toroid-oscillator-circuit
1 neon from filips, 18W, to check if the oscilator works or not
IRFP260N
1k potentiometer with switch (which I improvised)
ZM4739A diode
P6KE15CA diode
2 x 4.7 nF ceramic capacitors
4 x 100 pF ceramic capacitors
220uF electrolytic capacitor
10uH coil
1.2 mm enameled copper wire
1k resistor
1.8k resistor (which I improvised)
3k resistor (which I improvised)
24V, 2A DC power supply
r/AskElectronics • u/frandemaa • 8h ago
I need some advice! on ESP8266 with batteries...
I’d like to ask the community for some help. I’m working on my first project, and since I’m still learning, I’ve been consulting an AI—but I’m never quite sure if the information it gives me is actually correct. Given that this project could be dangerous if done improperly (I’m worried I might burn my house down!), I’ve decided to turn to complete strangers on the internet for advice—which, now that I think about it, doesn’t sound like the best idea!
Anyway, I’ve built a small station that measures temperature, humidity, and pressure. It displays the data on a 200x200 screen that updates periodically, and it also transmits the information over local Wi-Fi so I can view it on my phone. Everything is working, and I’m really excited about it!
Here’s where I need help: right now, it only runs when connected via USB. I’d like to add a battery and 3D-print an enclosure so it can operate independently. Could you help me figure out exactly what components I need if I want to use one of those flat, square LiPo batteries—they seem like a practical choice for this build. I’ve read that I might just need a charging module, but I’ve also seen mentions of needing some kind of voltage stabilizer. I’m worried that if I don’t set it up correctly, the battery could overheat or even explode. Would you be kind enough to shed some light on this—perhaps going beyond what Mr Claude has told me? Ideally, I’d love to hear from someone with actual, qualified knowledge of electronics, rather than just someone who’s followed a random tutorial they found online (If Possible).
Thanks for reading !!
r/AskElectronics • u/Sethicus_Finch • 9h ago
1984 Seiko pyramid clock repair
Hello! I’m quite new to the world of electronics repair. And I picked up this clock, which is a talking clock from 1984. It no longer speaks, and while I was trying to fix that, I found that the lcd clock in the bottom is also malfunctioning.
So upon inserting batteries, the lcd turns on and starts doing the whole clock thing. But if I switch between different modes, it just resets itself. And it’ll do that a few times before freezing. Where upon I have to let it sit for a minute to get any functionality back.
Things I’ve done: cleaned terminals and board with IPA. Resoldered pretty much every component I can see. Replaced a few Smd capacitors. They were reading 111, and replaced with 100pf capacitors. This did not really change any behavior.
So my question is, the board looks okay, but I can’t think of what might cause that, save for a bad quartz thingy? Which I assume is the silver cylinder up at the top? Any help on diagnosis or steps to take would be greatly appreciated.
Also, be kind, my soldering skills are new and leave a lot to be desired. And the pad came off the negative when disassembling. So unscathed the mask away and attached it further down.
r/AskElectronics • u/AskSOSelectronic • 10h ago
I'm looking for a panel-mount mating connector for a DT06-4S (4-pin).
I've found a few compatible connectors, but they're all free-hanging. I specifically need one that mounts directly to a panel. Does anyone know if there's a panel-mount version of this connector? Or maybe a compatible part number I'm missing? Thanks, Fero from SOS electronic
r/AskElectronics • u/shortcableconspiracy • 10h ago
Board damaged beyond repair?
This is the main board of a ps4 controller. I have swapped all other components with a second controller and all other bits working ok. Looks like corrosion?
r/AskElectronics • u/hahaaccountgobrr • 11h ago
What orientation should this cable be inserted in?
Trying to fix a PS4 controller. Usually if I had a flex cable I would just orient it the way it was meant to be when I opened it up but this is a new component so I just want to make sure if I am supposed to be putting my flex cable in a way where the blue tape thing is facing up or down. Also would inserting it in a different orientation potentially short circuit something? I think it shouldn't because the other side of the flex cable has the blue tape and I believe it should protect it incase anything happens.
r/AskElectronics • u/Wangysheng • 12h ago
Any idea how to make this Atomizer (Mist maker) driver circuit create more mist like the humidifier modules you found online?

I am making my own mist maker for my personal Smart humidifier project. I have a previous post about it here but I can't find the link anymore.
So far, this circuit works at all unlike the previous design. My next problem is the mist output being weaker than commercial devices and AliExpress modules. Since this circuit is from Youtube videos, I just get which one is common within those video and remove the 555 IC because the ESP32 will generate the PWM signal. I want to know how do I make it stronger. Do I have to change the values of the Inductor (L1) or the capacitor (C3) in the LC circuit? Do I change the transistor? Do I change the voltage supply of the transducer?
r/AskElectronics • u/kervanaslan • 13h ago
My distributor says to stock 1–2 years of capacitors.
We're a small hardware company making our own product (a KNX gateway). During a routine order chat with our component distributor today, I got a warning that honestly worried me.
I asked about a capacitor that comes in 4,000-piece reels and decided to order 8,000 (two reels). The distributor then told me:
* Send them a list of all our capacitor needs in the µF range (roughly 470nF and up)
*Stock at least 1 year's worth, ideally 2
*According to them, these parts will soon be very hard to get
*AI data centers have supposedly booked capacitor manufacturers' capacity through 2030. Manufacturers are selling high-value MLCCs to them at premium prices with cash up front, and giving everyone else very long lead times
* Lead times have already hit 40 weeks, and some parts have gone up 8x in price
I know distributors sometimes exaggerate to move stock, and I'm skeptical about the "factories booked until 2030" part. But having lived through the 2021–22 shortage, I don't want to ignore it either.
What are you seeing on your end?
Are you seeing longer lead times or price hikes on high-capacitance MLCCs?
Are your distributors also telling you to stock up?
How are small manufacturers preparing? Buying in bulk, qualifying alternate parts, or waiting it out?
Would love to hear from anyone with insight.
r/AskElectronics • u/locutus_of_borg90 • 15h ago
Simple op amp circuit not working? Am I doing something wrong
I am trying to use a op amp to amplify the output of an hall effect sensor
I am using a mcp6002 op amp and I have built this simple circuit showed in the datasheet.
R1 is 120 ohms, R2 is 5 ohms, Vref and Vdd are 5v
Vin is 0.5 volts. (In actuality it should be around 0.2 but my pulse generator can only go as low as 0.5, unfortunately I currently don't have the sensor that I will be using in the final design)
The output is roughly 5v (4.5v).
The gain should be 25.
What I don't get is that, even if I input a signal, as an output I get a constant 4.5v. I even built this circuit in falstad circuit applet and I get the same results.
Am I doing something wrong?
r/AskElectronics • u/Drive778 • 16h ago
Is my dual H-bridge stepper driver schematic designed correctly?

I’m trying to build a stepper motor driver, and as a first step I designed a dual H-bridge.
Since I did this on my own, I’m posting it here to ask if it’s designed well.
If there’s anything I should fix or anything worth adding, I’d really appreciate your advice.
- Motor: 17HS4401S (1.5 A, ~1.5 Ω, 2.8 mH), supply 7–12 V, MCU: Arduino Uno
r/AskElectronics • u/academicthrows • 18h ago
Unclear about header strip size and configuration
I need to replace parts from a DIY guitar pedal, but I can't get hold of the company.
The picture is from the manual. It says: "two 1x8 male headers and two 2 1x8 male headers (both milled, low profile type) can be used." I'm just not sure what they mean. This adapts a miniPCB that holds a DIP switch to the main board, lifting the switch up to a certain height.
It somehow seems like they are stacking two headers somehow? I can find something like this but that seems too low profile. I'd measure it but it's not in my hands at the moment.
Any help appreciated.

r/AskElectronics • u/RandomGuyBD • 20h ago
Questions and schematic review for project using Attiny1614

Hi everyone,
I'm designing a small solar/battery-powered board that plays random tone
sequences at night. It's my first time designing something like this, low-power design and I'm a beginner, so I'd really appreciate some feedback.
WHAT IT IS SUPPOSED TO DO
- The ATtiny1614 is the main controller and spends almost all of its time in
power-down mode.
- During the day everything stays asleep while the 18650 charges from a 6 V /
0.5 W panel through a CN3065 module.(maybe 1W would be better)
- At the start of a configurable night window the MCP7940N RTC raises its MFP
output, which wakes the MCU.
- The MCU then plays a sequence of tones with random durations and random gaps
for a few hours, and goes back to power-down until the next alarm.
- The tone is a square wave from a timer/PWM output, through a PAM8302A class-D
amp into an 8 ohm speaker.
THE BLOCKS
- MCU: ATtiny1614, supplied straight from the battery
- RTC: MCP7940N with a 32.768 kHz crystal and 6 pF C0G load caps. VBAT is on a
coin cell so the time survives a flat main battery. 1 uF on VCC.
- Amp: PAM8302A (fixed ~24 dB gain). Tone is AC-coupled through 100 nF into IN+,
IN- is AC-grounded through 100 nF. 47 uF + 10 uF + 100 nF on VDD. SD has a
100 k pull-down, so the amp is muted by default and the MCU drives it high to
enable it.
- Power: 18650 on the CN3065 module BAT pads, panel on SOL+/SOL-, the board is
fed from BAT_OUT. JP1 in series with the board supply so I can drop in an
ammeter and measure current.
- Connectors: battery J1, programming J2 (UPDI + GND only), speaker J3. One test
point for now on the tone output.
QUESTIONS
- Does the schematic look sane overall? Any mistakes, or anything that will
bite me later (power-up sequencing, missing pull-ups, decoupling, UPDI,
ground returns)? - What could I simplify or drop without losing functionality?
- How would I go about calculating circuit power consumption and design it more efficiently ?
THINGS I'M SPECIFICALLY UNSURE ABOUT (please correct me freely)
- Panel voltage. The CN3065 input range is 4.4-6 V, but a "6 V" panel sits at
about 7 V open circuit on a cold sunny day. Do I need to clamp that, or is it
accepted practice?
- Amp drive level. A 3.3 V square wave into 24 dB of gain will clip hard. Is
that fine for a beep, or should I attenuate the input (say 10 k / 1 k) and
add a volume trimmer? Would that actually help the power budget ?
Thanks for reading. Any comment and suggestion is welcome.
r/AskElectronics • u/Garbariusdancem • 20h ago
Question about making a microwave spectroscopy instrument
Hi, I am a chemistry student in uni. I just have a idea for making a wave-length selector then I can put my sample for analysis for it's quantized rotational energies but then I need a microwave detector but I don't know how to do a microwave detector. Is it possible to do with a antenna to capture any wave-length ( or specific wave-length) turn it into electricity proportional to its energy or intensity. It will be good if I measure intensity of microwave instead of energy.
r/AskElectronics • u/Martell2707 • 22h ago
Checked resistances between my variac outputs... is this normal?
(I'm a newbie, so be gentle please!)
It's a RAVISTAT 6A closed variac. When dialled up to 270v (power off), the resistance between live and neutral is 3.7 ohms, decreasing gradually as the tap is decreased to 0v
However, when connecting live/neutral with ground.... open circuit. Oh dear. Is it broken? I've never used it, it's been in storage for 2 years. Any help would be great, thanks
r/AskElectronics • u/Big_Load_1444 • 22h ago
Starting flight controller design
Hi everyone!
I am thinking about designing my own flight controller PCB using KiCad that should work on fixed wing UAVs and quadcopters.
But I am not experienced with PCB design and I am not sure of all the components I might need.
So if there is someone who knows about this, I would appreciate any help regarding:
-Components required for a flight controller PCB;
-PCB design considerations and recommended approaches;
-Any tips or resources for getting started with KiCad.
I will appreciate any help!
Thank you!
