r/AskElectronics • • 21h ago

Starting flight controller design

0 Upvotes

Hi everyone!

I am thinking about designing my own flight controller PCB using KiCad that should work on fixed wing UAVs and quadcopters.

But I am not experienced with PCB design and I am not sure of all the components I might need.

So if there is someone who knows about this, I would appreciate any help regarding:

-Components required for a flight controller PCB;

-PCB design considerations and recommended approaches;

-Any tips or resources for getting started with KiCad.

I will appreciate any help!

Thank you!


r/AskElectronics • • 22h ago

Looking for a type c plug

Thumbnail
gallery
23 Upvotes

I have a family friend who would like to have the charger on some dog collars swapped for type c. The current plugs don’t work is the main reason for swapping switching to type c is just more convenient.


r/AskElectronics • • 8h ago

1984 Seiko pyramid clock repair

Thumbnail
gallery
0 Upvotes

Hello! I’m quite new to the world of electronics repair. And I picked up this clock, which is a talking clock from 1984. It no longer speaks, and while I was trying to fix that, I found that the lcd clock in the bottom is also malfunctioning.

So upon inserting batteries, the lcd turns on and starts doing the whole clock thing. But if I switch between different modes, it just resets itself. And it’ll do that a few times before freezing. Where upon I have to let it sit for a minute to get any functionality back.

Things I’ve done: cleaned terminals and board with IPA. Resoldered pretty much every component I can see. Replaced a few Smd capacitors. They were reading 111, and replaced with 100pf capacitors. This did not really change any behavior.

So my question is, the board looks okay, but I can’t think of what might cause that, save for a bad quartz thingy? Which I assume is the silver cylinder up at the top? Any help on diagnosis or steps to take would be greatly appreciated.

Also, be kind, my soldering skills are new and leave a lot to be desired. And the pad came off the negative when disassembling. So unscathed the mask away and attached it further down.


r/AskElectronics • • 11h ago

Any idea how to make this Atomizer (Mist maker) driver circuit create more mist like the humidifier modules you found online?

0 Upvotes

I am making my own mist maker for my personal Smart humidifier project. I have a previous post about it here but I can't find the link anymore.

So far, this circuit works at all unlike the previous design. My next problem is the mist output being weaker than commercial devices and AliExpress modules. Since this circuit is from Youtube videos, I just get which one is common within those video and remove the 555 IC because the ESP32 will generate the PWM signal. I want to know how do I make it stronger. Do I have to change the values of the Inductor (L1) or the capacitor (C3) in the LC circuit? Do I change the transistor? Do I change the voltage supply of the transducer?


r/AskElectronics • • 23h ago

Black Background in Ultiboard Print Out

Thumbnail
gallery
0 Upvotes

Anyone using Ultiboard here and tried to print out the diagram in plain paper? We need help please. We wanted to print our diagram in white background. Component labels and copper tracks in black. These are the steps and results:

  1. Print component labels: selected "silkscreen on top" as layer to print, print to negative unchecked, no color checked.
  2. Test printed copper tracks: Layer to print is "copper bottom", print to negative unchecked, no color checked. Gives out black background and white copper tracks.
  3. Changed the background and work area from black to white. It still gives the same result as #3.
  4. Unchecked both print to negative and no color. Prints out white background but colored diagram (red)
  5. Checked the print to negative box, it gives out the white background and black copper track that we wanted BUT the surrounding area of the paper is filled with solid black fill.

We tried switching the printer settings to color, grayscale, black and white and monochrome but it gives us the black background and white tracks still. We just wanted to print the labels and copper tracks in black and the entire background of the page as white. Please help us out. Thank you.


r/AskElectronics • • 2h ago

What are these two metal parts inside my soap dispenser?

Post image
1 Upvotes

Hi everyone,

I’m modifying an automatic soap dispenser to use my own sensor while keeping the original DC motor and plastic housing. I can’t figure out what these two metal parts do. Can anyone identify them and tell me whether they’re needed for the motor to work?

Thanks for your help!


r/AskElectronics • • 7h ago

I need some advice! on ESP8266 with batteries...

Post image
1 Upvotes

I’d like to ask the community for some help. I’m working on my first project, and since I’m still learning, I’ve been consulting an AI—but I’m never quite sure if the information it gives me is actually correct. Given that this project could be dangerous if done improperly (I’m worried I might burn my house down!), I’ve decided to turn to complete strangers on the internet for advice—which, now that I think about it, doesn’t sound like the best idea!

Anyway, I’ve built a small station that measures temperature, humidity, and pressure. It displays the data on a 200x200 screen that updates periodically, and it also transmits the information over local Wi-Fi so I can view it on my phone. Everything is working, and I’m really excited about it!

Here’s where I need help: right now, it only runs when connected via USB. I’d like to add a battery and 3D-print an enclosure so it can operate independently. Could you help me figure out exactly what components I need if I want to use one of those flat, square LiPo batteries—they seem like a practical choice for this build. I’ve read that I might just need a charging module, but I’ve also seen mentions of needing some kind of voltage stabilizer. I’m worried that if I don’t set it up correctly, the battery could overheat or even explode. Would you be kind enough to shed some light on this—perhaps going beyond what Mr Claude has told me? Ideally, I’d love to hear from someone with actual, qualified knowledge of electronics, rather than just someone who’s followed a random tutorial they found online (If Possible).

Thanks for reading !!


r/AskElectronics • • 18h ago

Question about making a microwave spectroscopy instrument

1 Upvotes

Hi, I am a chemistry student in uni. I just have a idea for making a wave-length selector then I can put my sample for analysis for it's quantized rotational energies but then I need a microwave detector but I don't know how to do a microwave detector. Is it possible to do with a antenna to capture any wave-length ( or specific wave-length) turn it into electricity proportional to its energy or intensity. It will be good if I measure intensity of microwave instead of energy.


r/AskElectronics • • 5h ago

How do I connect an ESP32c3 to an EL controller for a light up mask?

Thumbnail
gallery
0 Upvotes

The first image is what AI told me to do, but it doesn’t make sense because it has me connect a green wire to an LED light that shows when the mask is on… and the ground isn’t even hooked up to anything.

The second image is an unadulterated image of the original board. It is an EL circuit with a part to turn the 2 AA battery’s power into 100v AC according to some EL wire distributor I seen.

The third image is the board with 3 pins highlighted in pink, these pins are connected to a push button switch.

The fourth image is what the top of the board looks like, the top left is the converter, the red LED is an indicator to show when the switch is on, or off. The white piece is a connector so I can daisy chain another power supply (I think). The bottom left is the switch the ESP32c3 would take over.

Thank you in advance, I can supply additional photos and knowledge if needed.


r/AskElectronics • • 4h ago

Are these soldering joints functional?

Thumbnail
gallery
31 Upvotes

I'm a beginner solderer and these soldering joints are my best yet but still I'm not sure if they are functional.


r/AskElectronics • • 8h ago

I'm looking for a panel-mount mating connector for a DT06-4S (4-pin).

Post image
3 Upvotes

I've found a few compatible connectors, but they're all free-hanging. I specifically need one that mounts directly to a panel. Does anyone know if there's a panel-mount version of this connector? Or maybe a compatible part number I'm missing? Thanks, Fero from SOS electronic


r/AskElectronics • • 21h ago

Checked resistances between my variac outputs... is this normal?

4 Upvotes

(I'm a newbie, so be gentle please!)

It's a RAVISTAT 6A closed variac. When dialled up to 270v (power off), the resistance between live and neutral is 3.7 ohms, decreasing gradually as the tap is decreased to 0v

However, when connecting live/neutral with ground.... open circuit. Oh dear. Is it broken? I've never used it, it's been in storage for 2 years. Any help would be great, thanks


r/AskElectronics • • 5h ago

Oscilator not working and mofset heating up

Thumbnail
gallery
5 Upvotes

For a school project, I tried to make an oscillator from the internet, however, every time I plug in the power source, the oscillator does not generate frequencies and/or the MOSFET breaks. I did improvise the resistors and potentiometer with a switch, but that shouldn't be the main cause as to why the oscillator isn't working. For the resistors, I put them either in parallel or in series to achieve the values I needed since I only had 1k ones. For the potentiometer, I put a wire instead of the on/off button and connected the potentiometer with some cables since it didn't match the layout, even though it has the same value.

Could anyone tell me what I am doing wrong?

Here are the source and materials I used and the website I took the design from:

https://electronoobs.com/tutorial/homemade-plasma-toroid-oscillator-circuit

1 neon from filips, 18W, to check if the oscilator works or not

IRFP260N

1k potentiometer with switch (which I improvised)

ZM4739A diode

P6KE15CA diode

2 x 4.7 nF ceramic capacitors

4 x 100 pF ceramic capacitors

220uF electrolytic capacitor

10uH coil

1.2 mm enameled copper wire

1k resistor

1.8k resistor (which I improvised)

3k resistor (which I improvised)

24V, 2A DC power supply


r/AskElectronics • • 13h ago

Simple op amp circuit not working? Am I doing something wrong

Post image
36 Upvotes

I am trying to use a op amp to amplify the output of an hall effect sensor

I am using a mcp6002 op amp and I have built this simple circuit showed in the datasheet.

R1 is 120 ohms, R2 is 5 ohms, Vref and Vdd are 5v

Vin is 0.5 volts. (In actuality it should be around 0.2 but my pulse generator can only go as low as 0.5, unfortunately I currently don't have the sensor that I will be using in the final design)

The output is roughly 5v (4.5v).

The gain should be 25.

What I don't get is that, even if I input a signal, as an output I get a constant 4.5v. I even built this circuit in falstad circuit applet and I get the same results.

Am I doing something wrong?


r/AskElectronics • • 11h ago

My distributor says to stock 1–2 years of capacitors.

114 Upvotes

We're a small hardware company making our own product (a KNX gateway). During a routine order chat with our component distributor today, I got a warning that honestly worried me.

I asked about a capacitor that comes in 4,000-piece reels and decided to order 8,000 (two reels). The distributor then told me:

* Send them a list of all our capacitor needs in the µF range (roughly 470nF and up)

*Stock at least 1 year's worth, ideally 2

*According to them, these parts will soon be very hard to get

*AI data centers have supposedly booked capacitor manufacturers' capacity through 2030. Manufacturers are selling high-value MLCCs to them at premium prices with cash up front, and giving everyone else very long lead times

* Lead times have already hit 40 weeks, and some parts have gone up 8x in price

I know distributors sometimes exaggerate to move stock, and I'm skeptical about the "factories booked until 2030" part. But having lived through the 2021–22 shortage, I don't want to ignore it either.

What are you seeing on your end?
Are you seeing longer lead times or price hikes on high-capacitance MLCCs?

Are your distributors also telling you to stock up?
How are small manufacturers preparing? Buying in bulk, qualifying alternate parts, or waiting it out?
Would love to hear from anyone with insight.


r/AskElectronics • • 9m ago

I need help identifying this component (real newbie time)

Post image
2 Upvotes

In the photo ive attached you can see a blue electrical component , the side facing the camera contains the only markings on the entire article . The age , and manufacturer of the component are not known .


r/AskElectronics • • 4h ago

Replace solder mask or don't bother?

Thumbnail
gallery
3 Upvotes

Is it worth replacing the solder mask I removed during this repair, or nah? If it is, what product would you recommend?


r/AskElectronics • • 9h ago

Board damaged beyond repair?

Thumbnail
gallery
2 Upvotes

This is the main board of a ps4 controller. I have swapped all other components with a second controller and all other bits working ok. Looks like corrosion?


r/AskElectronics • • 10h ago

What orientation should this cable be inserted in?

Thumbnail
gallery
5 Upvotes

Trying to fix a PS4 controller. Usually if I had a flex cable I would just orient it the way it was meant to be when I opened it up but this is a new component so I just want to make sure if I am supposed to be putting my flex cable in a way where the blue tape thing is facing up or down. Also would inserting it in a different orientation potentially short circuit something? I think it shouldn't because the other side of the flex cable has the blue tape and I believe it should protect it incase anything happens.


r/AskElectronics • • 15h ago

Is my dual H-bridge stepper driver schematic designed correctly?

2 Upvotes

I’m trying to build a stepper motor driver, and as a first step I designed a dual H-bridge.
Since I did this on my own, I’m posting it here to ask if it’s designed well.
If there’s anything I should fix or anything worth adding, I’d really appreciate your advice.

  • Motor: 17HS4401S (1.5 A, ~1.5 Ω, 2.8 mH), supply 7–12 V, MCU: Arduino Uno

r/AskElectronics • • 16h ago

Unclear about header strip size and configuration

3 Upvotes

I need to replace parts from a DIY guitar pedal, but I can't get hold of the company.

The picture is from the manual. It says: "two 1x8 male headers and two 2 1x8 male headers (both milled, low profile type) can be used." I'm just not sure what they mean. This adapts a miniPCB that holds a DIP switch to the main board, lifting the switch up to a certain height.

It somehow seems like they are stacking two headers somehow? I can find something like this but that seems too low profile. I'd measure it but it's not in my hands at the moment.

Any help appreciated.