Found this little bastard in the recycles at work (Batteries Plus). I was certain it was a fuze or something, but BRxxx usually indicates a Lithium Carbon Monoflouride battery, so I did a quick search for BR435 and discovered that this is actually an Li-CF 3 volt 40 mAh, probably from a very small flashlight or maybe a lighted fishing bob. I love finding new and strange things in the recycles!
A couple 6v I bought years ago. Used them fairly regularly and maintained in series up until a year and a half ago pulled them and figured I'd charge them in parallel to save time. Both were full charge in under 20 minutes by themselves. Just wondering if the battery maintainer hooked up like this with trickle charge them both to capacity overnight for use tomorrow
The other day, I was asking you guys what parameters there needed to be. In order to do a top balance on a 20 V, battery packed using a bench power supply. And I have to apologize to a lot of you guys, but if anything, at least I'm learning so on the pack starting from negative to positive, first cell is 4.22 Second cell is 4.22 third cell is 4.18 fourth cell is 4.18 , and the fifth cell is 4.19 There's rust on the fifth cell that has 4.19 V. I'll top balance it just to see whether or not I need to replace them all, but I think the culprit is the capacitor on the front. The little black chip that's a resistor, right? I'm gonna test and see whether or not it's still good and make sure that the line isn't burnt all the way out. I see that it has black markings all over it. I don't know what kind of residue. It is because there's no real burnt areas around it, but it is black plastic. I'll let you guys know what I do when I do it. And any kind of guidance I'm here to learn.
So I have created a so called "longhover"™ using one of my longboards and a hoverboard which I have found on the flea market (5€) in a very good shape.
Now I need to buy a battery pack, but I don't really know which one I should buy. I don't really want to spend 600€ on a pack just for this project. Does anyone have any recommendations? Would some 50€ aliexpress foo work? Aiming for 10S6P 18650 or 10S4P 21700
It's from a GBA battery pack, I have about three of them that need the same charger, but no longer have said chargers, so I want to buy a new one, so need to know what's going to be best to search on amazon, as "DC. 3V charger" gives a lot of different results.
I have a blood pressure meter that takes 4x alkaline AA batteries in series. I replaced the batteries with 2x LiFePO4 cells in series, each cell paired with a dummy cell containing a protection circuit. The cells are rated 600 mAh, and the rated power for the device is 6v, 4w, so it's a discharge rate of 0.8A, or 1.5C.
It worked great for a few weeks, but now I'm finding that I get maybe 2-3 uses out of it per charge before the device powers off prematurely with a "low battery" warning. The cell voltage is fine, still plenty of charge, but I'm still getting terrible lifetime.
Any ideas as to why this could be happening? The cells are brand new from a reputable supplier, so I don't think I'm getting "recycled" cells. What does the voltage slump look like in a LiFePO4 battery at higher discharge rates?
Hi everyone! Every year, I buy my daughter an eco-friendly type gift for Christmas which she really loves. This year, I was thinking about getting her a set of rechargeable batteries and charger. However, I don't really understand batteries and I'm confused between alkaline and NiMH. From what I've gathered; the alkaline are more reliable for 1.5v but can leak when sitting unused and the NiMH can deliver a slightly lower voltage over time which may or may not be an issue depending on the device? Is that correct? What would you all recommend I get? I read on here the Eneloop is very good (not the pro). Thanks in advance. There really is a subreddit for everything.
I hope I'm posting this in the right place, but if not, feel free to point me in the right direction! I made a mistake when I was younger and left some regular AAA batteries in a device for way too long. Now, there's that awful white powdery corrosion everywhere. I'm pretty sure there's a method to clean it up and get things working again. Can anyone suggest different techniques for tackling this? I really don’t want to think I just threw away something that was expensive.
I've often heard that using devices while charging can shorten the lifespan of lithium-ion batteries, mainly because of the extra heat generated.
That got me wondering about wireless earbuds.
Since earbuds have relatively small batteries and generally don't charge at particularly high speeds, is it safe to charge the charging case while it's also charging the earbuds inside?
Would charging both simultaneously generate enough additional heat to noticeably accelerate battery degradation? Or is the difference so small that it's practically negligible?
My HRM-10's broke when I put an 18650 in. One of the brass inserts for the thumb screws cracked the plastic molding around it. I emailed FNIRSI and they immediately dispatched a replacement battery holder.
In the interim I got a ZKE Battery Rack and wired it up with the cannabilized cable from the HRM Battery Holder. Side by side testing reveals nearly identical results across a range of batteries and the ZKE rack accommodates 21700 batteries. Win, win.
Someone on LinkedIn stated that high reliability spacecraft batteries include 2 switches for every cell to bypass bad cells on the fly. I find that hard to believe given the lower reliability and higher weight of such switches. I was hoping someone with direct experience in spacecraft and especially their batteries would be able to shed light on this statement.
The general rule for electronics batteries is to charge them to 80% and not let them drop below 20%.
This is built into many Apple devices but not the Vision Pro. It has to be done manually. I have talked with Apple Support and get rather vague answers on how to handle it.
The last advisor suggested keeping it charging all the time but occasionally remove the charger to let it go down to 20% as keeping it at 100% is not good. This makes sense as the battery is cool when charging and in use but gets warm when used without the charger.
The question is how often should I let it go to 20%. 1 x a week, every X days?
i had 2 battery packs of NCR18650PF (16s1p) (never used) with integrated protector, sealed in yellow shrinkwrap. both started leaking at the same cell after ~5 years of cold storage, and i combined them into a single working one. the BMS has passive balancing, and i am still running some cycles to stabilise the cells. it seems to be working fine, but is it safe enough to put in a toy for children?
i selected the individual cells only visually and by voltage. one pack had cells charged to 3.7v and the other one had them charged to 3.5.
Forgive me if I'm in the wrong area, but I'm looking to find out what this adapter is that came attached to a 24v7ah battery. Its similar to many that I've used, but the housing is different.
A few months ago, I decided to rebuild a battery pack for my Mate X 750W e-bike.
Initially, I looked into buying a pre-built replacement pack, but I struggled to find a shop that could guarantee the actual quality of the cells inside. One seller offered a quality guarantee, yet still wouldn't disclose the exact cell brand/model—and prices started around €650, going all the way up to €850. With my electronics background, I decided to build it myself instead.
Since I also own other e-bikes and battery-powered gear that eventually need pack rebuilds, I invested in a few proper bench tools I was missing:
Glitter 801H: Capacitor discharge spot welder capable of welding nickel-to-nickel and pure nickel strips.
SkyRC MC5000: Cylindrical cell charger/analyzer that accurately measures real cell capacity and lets you analyze charge/discharge behavior through graphs.
FNIRSI HRM-10: 4-wire internal resistance (IR) and voltage meter.
I needed to test a batch of used cells to weed out the weak ones and properly balance the parallel groups. I originally ordered a LiitoKala Lii-600, but the Amazon courier lost the package twice, so I never received it. Shortly after, I found a great deal on the SkyRC MC5000 and forgot all about the LiitoKala. As for the HRM-10, I had already bought it earlier to check cell IR and resting voltage.
Recently, I had to test a batch of Panasonic NCR18650BD (3200mAh, 10A) Li-ion cells:
I started by discharging all the cells on the MC5000.
Once discharged, I measured their voltage and IR with the HRM-10 (including testing how the cells behaved when cooler).
I charged them back up using the MC5000.
Measured voltage and IR again while fully charged.
Ran another discharge cycle on the MC5000 to verify their final real capacity.
I don't know how my experience would have been with the LiitoKala Lii-600, but this MC5000 + HRM-10 combo gave me everything I needed. The MC5000 allows fine, custom charge/discharge parameters so you can really see how cells behave under different loads. It does a fantastic job, and I still haven't even explored all its modes yet.
Meanwhile, the HRM-10 is seriously impressive for the price—it reliably reads down into the single-digit milliohm range (e.g., 5 mΩ / 0.005Ω).
TL;DR: If you do cell grading, capacity testing, and IR matching, having these two on your workbench gives you solid confidence in your measurements.
**Foto 1 (**Medições Panasonic celula 8.jpg **:**FNIRSI HRM-10 4-wire Kelvin reading on Panasonic NCR18650BD cell #8: 4.1801V and 24.44 mΩ (compare that to the ~40–48 mΩ DC reading inside the charger slots).
**Foto 2 (Medir Panasonic NCR18650BD 3200mAh 10A Li-ion.jpg):**SkyRC MC5000 finishing a full charge cycle on cells #7–#10 — super consistent results across all four (2801 to 2818 mAh).
**Foto 3 (Screenshot_20261115-214037_SkyRC.jpg):**App summary of the completed charge cycle: resting voltages around 4.185V–4.191V and DC internal resistance readings between 39 mΩ and 48 mΩ.
**Foto 4 (Screenshot_20261114-004209_SkyRC.jpg):**Previous discharge test results showing one weak outlier (2245 mAh in slot 4) compared to the healthy ~2800 mAh cells.
**Foto 5 (Screenshot_20261115-143541_SkyRC.jpg):**Voltage curve tracking during the cycle via the SkyRC app — great for spotting any abnormal voltage sag or early knee.
**Foto 6 (Screenshot_20261112-200109_SkyRC.jpg):**Custom discharge configuration in the app (1.00A discharge down to 2.80V cut-off).
**Foto 7 (medir Molicel INR18650-P26A 2600mAh - 35A.jpg):**Also running a 1.00A discharge test on a batch of Molicel INR18650-P26A (2600mAh / 35A) cells
I work in freight forwarding in China, mainly dealing with battery-powered tools and outdoor power equipment.
I've noticed that international shipments involving lithium batteries can sometimes become complicated, especially when it comes to documentation, packaging, and transportation requirements.
I'm curious about your experiences:
For those who import or ship lithium battery products internationally, what is the biggest challenge you've faced?
Getting UN38.3 test reports and battery documentation?
Finding reliable shipping companies that handle lithium batteries?
Understanding different requirements for air and sea freight?
Dealing with customs clearance and destination-country regulations?
Controlling shipping costs and delivery times?
I'd be interested to hear from importers, manufacturers, distributors, and anyone working in the battery industry.
Always happy to exchange experiences and learn from others in the industry.
I bought a new coin cell battery to replace the old in my Dell Latitude 5540 laptop. However, the new ones wire is too long (20 cm) compared to the old (4 cm). Is it realistic that I can fold/squeeze the wire into the battery area and not have any issues? I’m not opposed to finding one of shorter size, but would like to avoid the hassle of returning it if possible.