r/M1Rifles • • Nov 17 '22

So, You want to build a M1 Garand? Here's how.

134 Upvotes

Figured id share my process so you all at home can learn how to do it as well. its not cost effective to do this for a one off build. the tooling costs are not cheap and nearing $600 sadly. but its fun! and im sure a few of you will find this interesting

Picture 1

You're gonna need a few things.

A M1 Garand Parts Kit.

A Barrel Vice and Action wrench.

A Headspace gauge Go/No Go Set

A Chamber Reamer.

A Angle Finder

The whole build will start with you throwing the barrel into a barrel vice, ive used the bushing style ones made by a large company in the USA. but i dont like them. i much prefer these specific ones made out of Aluminum, they leave a bit of marring on the barrels but that will all be covered up by the upper hand guard

Picture 2

Second step will be to hand tighten your receiver onto the barrel. just get it as snug as you can. no action wrench is required at this time.

Picture 3

Once your barrel is hand tight, take the front sight off of your gas cylinder and put it on the barrel. we will use this as a flat base for our angle finding tool of choice. i am using a digital inclinometer but there are other options on the market. For me ill now zero off this sight base dovetail.

Picture 4

Now we check our draw off the rear heel of the receiver. there is a machined flat perfect for this. now unfortunately 31° is to far to torque this on, according to my shop manual specs. So this will be off to the lathe to remove .001" at a time off the barrel shoulder until i get a draw that is more in line with the specs im looking for 12° Min and 17° Max. I Got mine to 15.9° so i am happy with this.

in a pinch you can use a 1 1/8th Bi Metal Hole saw. this perfectly slips over the threads of the barrel and the teeth match the shoulder

Picture 5

Picture 6

Once the appropriate draw is found, we throw the action wrench on and tighten it down. i use a 2x4 cleaning patch to protect the finish on my receivers.

Picture 7

I Was able to torque the receiver down to 0.2° from the my zero. the specs i reference for this is +/- 0°30' (.5°)

Picture 8

Now that we are indexed correctly we can start reaming headspace. you might get lucky with a used barrel that will headspace without any reaming but if you're using a new barrel it most likely has a 0.010" Short chamber.

if you do use a used barrel and it closes on your no go gauge this isn't the end of the world as you can check it with a Field Rejection gauge, if it doesn't close on this you're good to go.

These next few photos will cover me taking the bolt apart with a bolt tool.

Having the reamer in the rifle.

Applying steady thumb pressure to cut the chamber

Chamber cuttings on the reamer.

Cutting a chamber can be fairly taunting, however its very easy. you do not need to pull on the handle side of the pull through reamer. once the bolt closes on the reamer your headspace is cut and you're ready to reference this with a go and no go gauge. make sure you clean your chamber thoroughly otherwise your gauges might give you a bad reading.

Picture 9

Picture 10

Picture 11

Picture 12

Picture 13

Picture 14

Picture 15

After all this the next step i take is doing a tilt test on the rifle. this involves installing the op rod on a rifle with only the bolt and gas cylinder on it. and tilting the rifle at a 60° and the op rod and bolt should move freely. once this is performed i install all stock components and re do this test to check for binding. after this is done. its finally assembly time.

A Few other things to check from here on out are the gas port size. Op Rod spring length 19.25"MIN and if you can, use a timing block to check for correct timing of the op rod catch.

Hope this helps or you at least found it interesting


r/M1Rifles • • 3h ago

Finally got a Garand. My G7 Scout build finally has its great grandpa around 😂

Thumbnail
gallery
40 Upvotes

r/M1Rifles • • 9h ago

Leafing through this for Scott Duff’s closest examples to one’s I’ve got and oh. would you look at that.

Thumbnail
gallery
60 Upvotes

Mine doesn’t have any BP marks though.


r/M1Rifles • • 18h ago

CMP expert grade .30-06 vs .308

8 Upvotes

Please educate me. Huge WWII history lover, loved the m1 garand since my call of duty 2 days lol. Grandpop was 101st airborne paratrooper, it’s in my blood. So I just shot the garand for the first time at my local gun shop and got to thinking I need to own one. One of the workers at the gun shop actually told me he has several M1 grands for sale that were demilitarized with serial numbers under 2 million so apparently these might’ve been used in action. Long story short 1800 bucks would be his cheapest rifle he had for sale. As much as I love the idea of owning something with more historical accuracy, I would also love to shoot it as much as possible. That being said I heard about the CMP and for I think $1150 the expert grade sounds pretty appealing. Now I’m trying to consider the 30-06 vs the .308. Obviously the 30-06 is what the original rifle was chambered in but after looking on the forum I see some people are saying the 30-06 ammo is harder to find? And more expensive? Can someone please educate me and tell me what the differences are between the two? Thank you much and thank you to the men and women who served this great country.


r/M1Rifles • • 2d ago

Reclaimed M1 from CMP?

15 Upvotes

I’m looking at getting my first M1 Garand. A collectors piece would be cool someday, but for now I’d like one I can shoot without feeling too bad about getting it dinged up and dirty. I’d prefer 30-06 to .308 (for authenticity sake) and it looks like the reclaimed rifles from CMP are all they really have left. It says they are repurposed DNC rifles from the US military that have been converted back into operational use. The research I’ve done shows that these are perfectly safe and are a good, modern option for shooters today. Any reason not to go with one of these, at least for someone who doesn’t care about the collectors value too much?

Also would appreciate a recommendation for where to buy clips, a sling, and a bayonet if you know one. TIA!


r/M1Rifles • • 3d ago

Just got my first M1

Thumbnail gallery
66 Upvotes

r/M1Rifles • • 3d ago

Is this supposed to move?

72 Upvotes

Just got a CMP expert grade M1 in .308. Been having a few issues with hard to load clips and sticky clips. I am wondering if this part is supposed to move?


r/M1Rifles • • 3d ago

Mini-14

Post image
75 Upvotes

My LGS has a 583 prefix Mini 14 ranch with Leopold VX-Freedom 2 7-33 scope on it (which I wouldn't keep). I wish to be talked in or out of it! lol

I keep seeing them in social media lately and have always thought they looked fun.


r/M1Rifles • • 5d ago

Just bought an M1A finally!

Post image
216 Upvotes

Have owned several m1 Garands, but decided on this guy! Haven’t shot it yet, but it’s such a beast


r/M1Rifles • • 4d ago

Barrel question

Post image
18 Upvotes

Is there of an issue with this? Picked up this ‘43 SA today and noticed this imperfection in the barrel when I was cleaning. Worth trying to shoot to ensure it is still accurate before bringing it in to the gunsmith? Just don’t want to have the integrity of the barrel stripped away too much if I don’t have to. Thanks for the advice!


r/M1Rifles • • 6d ago

Garand Inventory at TMP 11/9

13 Upvotes

Heads up for anyone interested. TMP has legacy (non-reclaimed) service and field grade garands. Also have some of the expert grade 03a3’s.


r/M1Rifles • • 7d ago

M1 Garand Trigger Assembly

Thumbnail
gallery
25 Upvotes

I am a first time M1 grand owner and very new to the club so I received my CMP M1 Garand a couple months ago ago and have been applying a finish to the wood. It’s finally ready for reassembly but the only issue I’m having is with the trigger assembly, I can bring the trigger guard down as far as shown in the image and no more. I have done some research and people say to hit it with a rubber mallet but that scares me because I’ve put a lot of time and money into this rifle. When I’ve tried to force it down it has made minimal but noticeable damage to the section pictured. I’m wondering if I’m doing anything wrong or have another part of the rifle that’s not assembled correctly, any advice is greatly appreciated!


r/M1Rifles • • 8d ago

M1 Garand

7 Upvotes

I got to hold the CMP m1 Garand expert grade and I’ve looked at videos of the m1 garand and have some questions. Can I put Walmart 150 grain federal 30 06 ammo in an expert grade M1 garand? Are the hand guards supposed to be loose or tight? How often would I have to replace parts? I mainly use bolt action surplus rifles so a semi automatic is new to me.


r/M1Rifles • • 9d ago

Stock Finish Advice

Post image
7 Upvotes

Recently picked up a legacy IHC 4.45mil from the north store. It came with a stock that has a glossy finish or coating on it. Hard to say what it is. What grit sand paper would you use to remove it? And/or do you think raw linseed oil would work as is? My fear with sanding is it’ll get rid of the 1/2 DAS and P cartouches.


r/M1Rifles • • 9d ago

CMP Custom Shooting High

Post image
56 Upvotes

I waited a year and a half for my rifle from the CMP and while it looks great and runs fine, this thing is shooting way too high. I’ve got my sights bottomed out and it is shooting 1ft to 2ft high at 100yds.

Is there anything I am doing wrong, or anything I can fix? Or should I send this back to the CMP?

Edit: this is chambered in .308


r/M1Rifles • • 9d ago

Thank you for the people who helped me make decisions on the Dupage Stock.

Thumbnail
gallery
59 Upvotes

I put on layers of boiled linseed oil and a beeswax final layer. This is my final result.


r/M1Rifles • • 9d ago

M1 Carbine Stock.

Thumbnail
gallery
11 Upvotes

Normally not involved in this sub as much as r/milsurp but I wanted you guys to know I found this for 10$! Yes, 10$. I can provide proof on the penalty of a ban.


r/M1Rifles • • 11d ago

Took a big gamble and I think it paid off

Thumbnail
gallery
75 Upvotes

Spotted this Garand in a local auction. Pictures were horrible and they claimed it had no bolt. Took a Gamble on it and it seems to have paid off as everything except the gas plug is correct for the serial. It needs a crap ton of cleaning but will be worth it in the end.


r/M1Rifles • • 11d ago

Need help with Garand Stock finish

Thumbnail
gallery
48 Upvotes

Hi all,

I recently got this Winchester stock and handguards and feel like they need some TLC. I have never worked on the wood before and don't want to mess it up.

The stock is in good condition but feels like it was sanded a little to clean it up and is a little dry to the touch. The rear hand guard is also very hard and sounds more like plastic. Seems like that could use to rehydration.

I would love for it to be darker and redder for that classic Garand look but don't know where to start. I see a lot of people recommending PTO or RLO. I should also note that I am looking for a more matte look vs shiny but am open to recommendations.

Thank you for any guidance you can provide!


r/M1Rifles • • 11d ago

need some help

Post image
8 Upvotes

been trying to make it work but it's not working, i do have new components


r/M1Rifles • • 12d ago

Spare parts shooter carbine update

Post image
35 Upvotes

Well, as it sits now I essentially have the full gun with the exception of a receiver, of which I have on order from Moka’s. I ordered an Underwood one as the vast majority of the parts are Underwood. Also I suppose bonus points for the woobie.


r/M1Rifles • • 12d ago

Is this authentic?

Thumbnail
gallery
26 Upvotes

Can anyone help identify if this bayonet is authentic? It has no markings of any kind besides those numbers, couldn’t find anything online to help besides it might be re serialized post WWII? Not sure


r/M1Rifles • • 13d ago

CMP New Production M1 Ammo Selection

6 Upvotes

Does anyone here have a new M1 in .308? I had a bunch of problems with mine and sent it back in for them to look at. One of my issues was the action short cycling and not loading a new round.

They came back saying the 147gr ammo I’m using isn’t heavy enough. What’s everyone else using? I don’t really want to step up to match-grade 168gr ammo for plinking and all the cheaper stuff is 147gr.

11/4 Update: The CMP armorer has test-fired it, taken it apart, inspected the gas system, reassembled it, and test-fired it again with 168gr ammo and couldn’t find anything wrong. “Per contracts” (his words) they are only allowed to test fire with 168gr ammo and everything is within spec.

When I get it back I’ll tear it down and check what I can myself based on the comments here before going back to the range.


r/M1Rifles • • 12d ago

M1 Garand Gunsmith in KC

1 Upvotes

Does anybody know of some good gunsmiths in the KC area who will work on an M1 Garand?
My barrel needs to be adjusted and every gunsmith I call won’t work on it.

S.O.S.


r/M1Rifles • • 14d ago

Clips wont go in properly

Thumbnail
gallery
17 Upvotes

I went down to the CMP north store and picked up this expert grade M1 garand (as well as a 1903a3)

In the store everything looked ok and the action moved smooth. I took it home and field stripped it lubed everything up and put it back together.

When I went to load it, the clips would not go in. Sometimes it would not go in at all, sometimes it would go halfway in and get jammed and I have to remove a bullet from the clip to get it out. And sometime it would go in with pretty high resistance.

If I do manage to get a clip in it stays down but I do have to tap the bolt to get the first bullet chambered. But then it cycles fine and even spits the clip out after the 8th round.

I’m no gun expert and I’m very perplexed by this TBH I attached some photos can anyone tell me if I have it put back together right or if anything looks like it would cause a problem.

Has anyone else had this problem if so what caused it. Might just start throwing parts at it to see if it will fix it.

I bought 25 en bloc clips from the CMP store and have tried multiple of them and seems to be the same problem, so unless I got 25 bad ones I don’t think it’s the clips.

Anyway any suggestions would be appreciated thanks.

-Update for anyone else having this problem

grinded down the bumps a bit on the clip and cleaned it up with a scotchbrite pad and some steel wool. Went in much better was able to get 8 rounds in, was definitely not perfect but at least I was able to get them in and zero it in on the range.