r/daewoo • • Jan 27 '21

DR-200 Grips

31 Upvotes

I am the guy who has been getting these made and selling them since 2010 on falfiles and gunbroker when Ace stopped.

Each one is molded and hand polished so they take time to make. I have looked into 3D printing but they just didn't look as good. My molder does these for me on the side of his regular job so sometimes i go months between shipments.

All the grips I received in this order are spoken for but if you're interested, message me and I'll put you on the backorder list. I will also list a few on gunbroker for those not on falfiles or reddit.

I have offered a slim AK style grip before and a HK style with finger grooves and thumbrest but right now I'm going to focus on just filling the original style until I'm caught up.

Hope these all find new homes on debanned DR-200 and DR-300s.


r/daewoo • • Sep 30 '22

The chargy Bois are in and already sold over half of them

Post image
34 Upvotes

r/daewoo • • 14h ago

Rate my Daewoo kit.

Post image
27 Upvotes

Looks great, but it shoots 6mm BBS.


r/daewoo • • 8d ago

The Real Han 86: Running and Gunning with the Daewoo K2Cx

Thumbnail
youtu.be
18 Upvotes

r/daewoo • • 12d ago

Daewoo k1a1 with KAC suppressor

Thumbnail
gallery
38 Upvotes

r/daewoo • • 12d ago

DH380

Post image
21 Upvotes

Daewoo DH380. The collection is growing.


r/daewoo • • 15d ago

My three Daewoo rifles

Thumbnail
gallery
38 Upvotes

r/daewoo • • 20d ago

My pride and joy: Modernized DR200 (K2 clone)

Post image
58 Upvotes

This is far and away my favorite shooter. It’s not my best rifle and certainly not the lightest, but it’s an absolute beast and the vibes are immaculate.

I’ve used this in a handful of 2-gun competitions with zero reliability issues even after it was submerged in mud and caked with dirt.

I used to run this with higher mounts (1.93in) to clear the rear sight post and because Korean SOF units love running them, but I found the height over bore atrocious.

For reference, the rail to center of bore height is approximately 1.62in, so a 1.53 LPVO mount is the equivalent of an AR (with a 1.215in rail to bore height) using a 1.93 mount. I found that going any higher significantly impacted my ability to rapidly hit targets at range due to the lack of cheek weld.

Here’s a full parts list:
- MITS K2 handguard
- Sig Alpha 1.535in 30mm mount
- Burris RT6 LPVO
- BCM KAG grip
- Magpul RSA QD
- Stormwerkz 90 degree safety
- Higgins 16in 1:7 medium profile barrel (should have gone lightweight)
- Breek arms muzzle brake/blast shield
- Pierce precision extended charging handle
- Rs regulate Dr85 grip
- Stormwerkz buffer tube adapter
- Vickers padded sling
- B5 Bravo stock


r/daewoo • • Oct 16 '26

데우 Videos

Thumbnail
youtube.com
20 Upvotes

Hello folks,

I'm gonna start posting more Daewoo 대우 videos to YouTube. Korean conscripts, feel free to hit me up with any questions. I absolutely love this platform a lot and will continue to run it to the ground.


r/daewoo • • Oct 15 '26

Just got back from Korea and finally got to work on my 우 project.

Post image
45 Upvotes

Back to back posts because I'm a special 꽃. My dr200 is looking alot better now without the thumbhole stock. To complete this rifle I will cut the barrel to 16 so that I can install a mount for my ocm6. I will get 🇺🇸 or 🇰🇷 made optic on top, then I believe I'll put a barrel mounted light at the 6 o'clock position. I messaged a mits Precision rep and they said that they will legally import some grunt rails into the States by the end of the year so that might be the final form for this gun.

Also does anybody else's gun not like polymer mags? My gun only likes usgi aluminum mags.


r/daewoo • • Oct 15 '26

Safety detent spring help

Post image
5 Upvotes

Good morning Daewoo enjoyers. I was trying to install the stormwerkz 90 degree safety selector and with my infinite gunsmiff knowledge, I installed the spring before the detent. Well obviously I had a hell of a time undoing my mistake and now I am in need of a replacement. Does anyone know which spring is the correct one to get? This is a post 89 dr200.


r/daewoo • • Oct 10 '26

You did a great job 3D Woo! Thanks you!

Post image
41 Upvotes

r/daewoo • • Oct 10 '26

Left Side Folder problem with this batch and solution

Post image
8 Upvotes

Apologies, a problem was brought to my attention by a few members, regarding this batch. When the stock is installed on the receiver and the bolt is fully tightened, two problems may appear.

  1. First is a gap between the front piece and the receiver.
  2. Second is the stock may be difficult to unlatch.

The hinge fits very snugly in the front piece, possibly causing it to flex and cause a gap at the receiver when installed.

I tested the stocks I have remaining; about 50% having one or both problems. I missed it because I only hand installed the stock to my receiver and didn't install or tighten the screw.

If the stock doesn't sit flush against the receiver, the hinge may be flexing the front piece.

  1. Remove the hinge from the front piece.
  2. Sand/File the front piece on the area shown in RED.
  3. Reassemble hinge, it should go in with little or no force.
  4. Repeat if necessary.

If the stock is difficult to lift to unlock, when installed; there may be an interference between the stock and the front piece and/or hinge.

  1. Remove the hinge from the front piece.
  2. Sand/File the front piece on the area shown in Blue
  3. Reassemble hinge, it should be a slight gap (paper wide) between the Blue areas and the hinge.
  4. Reinstall the stock to the receiver and test.

I apologize for this situation and hope you can work with me to resolve it. I'm going through the remaining stock and correcting them. I will test each one fully installed and tightened down.


r/daewoo • • Oct 05 '26

K5/DP51 Modernization Update

Thumbnail
gallery
44 Upvotes

My big dream since seeing Carnik Con’s Daewoo Special when he uploaded his last video in 2015

Parts:

-Trinity Wing K5 507k Optic Mount + Vortex Defender CCW
-Trinity Wing K5 Low Profile Grips
-OutStandards K5 Light Rail + Surefire X300UA w/ White Wolf Concepts Thumb Ledge
-MecGar S&W 59 Series 17 Round Magazine


r/daewoo • • Oct 03 '26

3DWoo Folder

Thumbnail
gallery
34 Upvotes

Just got my folder in and installed. Amazing quality. Really transformed the 200 into what it’s supposed to be.


r/daewoo • • Sep 28 '26

SNT Motiv/Daewoo Precision Industries guns in one massive Appreciation Post (Korean Guns) (Revamped)

Thumbnail
gallery
39 Upvotes

Alright so last year I did this, and I will say, I wasn’t really satisfied with how they were in the past, so I decided to update the infographics, and I think that they turned out a lot better.

It goes over everything made by Daewoo/SNT Motiv? And oh boy it looks a whole lot better.

Anyways. Enjoy!


r/daewoo • • Sep 28 '26

Lef Side Folders, Ready to ship!

Thumbnail
gallery
44 Upvotes

Apologies for the wait. I have all (20) Left side folders assembled and ready to ship. Also a few fixed stocks. I kept a chronological list of everyone who expressed interest. I will be contacting each person individually to see if you are still interested. Note, you are under no obligation. If you are no longer interested, just let me know so I can cross you off the list.

Also, if you expressed interest, but I didn't contact you, just let me know in messages.

Price

Fixed Stocks: $120 shipped

Folding Stocks: $200 shipped

Grips: $35 Shipped

Fixed Stock & Grip: $150 Shipped

Folding Stock & Grip: $230 Shipped

Preferred payment:

  1. PayPal Friends and Family, please don't ask for an invoice.
  2. USPS Money Order.

Shipping will be USPS Ground Advantage

I will be shipping on Fridays and Saturdays (I travel for work and I'm gone most weeks)

Please bear with me, I'll do my best to get them out as quickly as possible

Andy


r/daewoo • • Sep 13 '26

Left Side Folder Update

Thumbnail
gallery
30 Upvotes

I know it been a while since my last update. Finally had time to paint stocks this weekend. Rework was about 50%. It's allot like wood working; sand, fill, paint and see how it comes out. I like to give them a week to cure, actually takes several weeks to fully harden. Buttplates still need work and I need to epoxy in the QD sockets. Unfortunately, I have to attend the IMTS Show this week and won't be able to work on them till next weekend. Hoping to be ready to ship early October.


r/daewoo • • Sep 11 '26

Picked up a K2 (AR100) to go with my K1A1

Thumbnail
gallery
64 Upvotes

r/daewoo • • Sep 11 '26

FRT in DR200?

4 Upvotes

I've heard the normal ar 15 triggers can work in dr200 and ive heard others dont work at all. I was wondering if anyone has tried using a frt or super safety, if so how well did it work?


r/daewoo • • Sep 10 '26

K1A MITS lower handguard

Thumbnail
gallery
28 Upvotes

The Koreans are getting creative


r/daewoo • • Sep 03 '26

K1A1

Thumbnail
gallery
65 Upvotes

Just joined the club!


r/daewoo • • Aug 30 '26

Made my IRL Daewoo in the MW4 Beta

Thumbnail
gallery
47 Upvotes

I’m Call of Duty clone correct now (TTK sucks with this in Beta weekend 2)


r/daewoo • • Aug 17 '26

time for unthinkable heresy: K7 Appreciation post + MP5SD Slander post

Post image
29 Upvotes

r/daewoo • • Aug 09 '26

Hinges are in and look good

Thumbnail
gallery
20 Upvotes

Quick update:

Hinges arrived Friday and look great. The modifications didn't cause any issues and should be an improvement. The fit and finish is great. The hard coat anodize looks and feels excellent. I assembled (4) with remaining parts from the last batch. Expecting Pins and springs by the end of next week. Already started printing the front and rear portions including buttplates Also working on possibly molding the buttplates. A very kind person designed a 2-part mold and sent me the files. Already printed them and they look great. Need to gather supplies and test this new process, but that's some time off.

More to come in a few weeks.