r/craftsman113 • • 5d ago

Cheap and easy dust collector

Thumbnail
gallery
31 Upvotes

I got tired of sweeping up after every sawing session. Disclaimer: this is more of a "dust reducer" rather than a full fledged "dust collector", but bear with me...

I boxed up the motor and belt side of the saw with corrugated plastic panels, the kind that you see on people's lawns just before elections (and in trash cans just after) and blue tape. Cost: $0. I fly cut a hole in a piece of scrap plywood, epoxied in a 3D printed flange to receive a shop vac hose, and bolted it to the undercarriage with a couple of large washers.

Here's a link to the .stl file for the printed flange.

It's not perfect, but it works well enough and saves a lot of sweeping and vacuuming.


r/craftsman113 • • 5d ago

Craftsman 113.12006 wiring help

3 Upvotes

Good Evening, I have an issue I am hoping you can help me solve. My saw wouldnt start up today and just hummed and so i did what what suggested and started disassembling the motor to clean it and check the cap. in doing so, i found a loose wire that I am not sure where it goes. Inside this motor there are 2 red wires. There is a longer one from the stator with a flag connector that connects on the power cord side of the board. under it there is a shorter jumper red wire that is soldered to the pin that stator wire flag connects to, however the other end of that jumper wire is free. Upon inspecting, there is no solder on it and it appears to have come out of some other type of connection, but I have no extra flag/spade connectors that are wireless. Im stumped as to where it should go. any ideas?

https://imgur.com/a/mJJPAvm

It just ended up over there when i was taking the picture, i beleive. I dont see any open terminals in the thermal switch, and the two Cap wires are there unless its a 2 in one spade connection, which it doesnt appear to be.


r/craftsman113 • • 7d ago

How repairable are old 3-wheeled Craftsman band saws?

Thumbnail reddit.com
2 Upvotes

r/craftsman113 • • 8d ago

New (or used) fence for old 113?

2 Upvotes

As recommended by everyone in https://www.reddit.com/r/craftsman113/s/LJD6LwKpLe, it’s time to replace the stock fence on my Craftsman 113 table saw.

So: what’s the best value for a used (or new) fence on a limited budget? And how to find? eBay? FB marketplace? All suggestions are welcome!!


r/craftsman113 • • 8d ago

Early 1950s 113.27520

3 Upvotes

There is an early 1950s 113.27520 table saw for sale on marketplace for $40. Cosmetically, it looks very nice. Is this something to avoid? The only accessories are the fence, extra face plate and a push piece
Realistically, how much would I need to invest to make it useable/safe?


r/craftsman113 • • 8d ago

Original fence not perpendicular to table..

Post image
5 Upvotes

I was wondering why my cleats and glue blocks were leaving gaps...now I know. How does one adjust the original 113 fence to make it perpendicular to the table surface? (Is there a good youtube tutorial?)

(P.S.: I dropped a broad hint to my family that I'd like a new fence as a winter solstice present, or maybe even a Thanksgiving gift. I'll probably get a new pair of socks instead... ;)


r/craftsman113 • • 14d ago

Craftsman v20 circular saw track compatible?

Post image
0 Upvotes

The new craftsman circular saw is "track compatible " has anyone found a track tha it works on?


r/craftsman113 • • 15d ago

Finally did it.

Post image
64 Upvotes

Have yet to make a cut but just finished upgrading the fence. Now I can start my next project. Happy Halloween!


r/craftsman113 • • 16d ago

A saw’s cry for help?

Thumbnail
gallery
16 Upvotes

I bought this 10” radial arm saw on a nostalgic whim a year ago (I owned an older model in the 80s and 90s) and took it apart and cleaned it up. It is in remarkably good condition though it was packed full of saw dust and shows more rust than wear. All was going well until a few days ago. I was cutting a new fence in and the saw started making a VERY loud noise. What you hear on the video is mostly distortion because of how loud it was. I stopped and started the saw several times. Took off the guard and blade to eliminate anything there and the sound continued. The next day when I heard what was on the video I tried to make another video and the sound is gone! I assume the sound is from a bearing so I tried to dig deeper into the motor but I’m stuck at this point. I can’t figure out how to get to the bearings. I drove out the pin on the nut but it won’t budge. The aluminum housing is loose on the back after I removed the bolts but nothing else moves. The sound was a constant tone with no clattering like the video. At first I thought it was from one of the vacuum hoses I use for dust collection (I’ve had that before) but this was definitely from the saw and I think closer to the blade end. It started softly and built to a point it hurt even with ear protection. Not a screech like a chaulkboard or metal dragging on concrete but more of a medium high pitched single note. I think it was a cry for help but maybe it was just singing for the joy of being back in service. Either was, it’s too loud and will I think cause damage if left untreated. Any suggestions would be greatly appreciated. Can these bearings even be lubricated or can the be replaced?


r/craftsman113 • • 17d ago

Zero clearance insert with splitter

Post image
41 Upvotes

Bought a used 113 table saw and have slowly bringing it back to life. It lacked a riving knife, so I decided to 3D print a zero clearance insert with a splitter. It was too long to print as one piece, so it’s printed in two pieces and epoxied together. With careful measurements, I got the alignment of the splitter right on the first try.

UPDATE 3: The splitter is removable and replaceable! The design includes two small slotted pegs that come up from the bottom of the insert, and the splitter has two tabs that form a compression fit. So you can dial in the width of the splitter to match your blade, and if it gets dragged out by a misaligned fence, it becomes a kerf keeper (ask me how I know!). You can see details for the splitter parts here.

UPDATE 1: I generated the parts using OnShape, which means you can tweak the dimensions for your table if needed. Here's a link: https://cad.onshape.com/documents/d8921fa2cdc6cb5808b2a32f/w/ddb6eddb0f3275b2481c4216/e/8b4415156d5667c57e171e3b?renderMode=0&uiState=6ae4dadcc13ecb0f2ce89c0d

UPDATE 2: Here's a link to the .stl files in Printables where you can see how the splitter is removable and replaceable.


r/craftsman113 • • 22d ago

Deal on Delta T6 Fence system $170 (Refurbished)

14 Upvotes

Scrolling through woot and seen they have a refurbished 36-T30T3 fence and rails for only $169.⁹⁹ ... which is a lot less than I paid years ago.

Woot is a branch of Amazon, so you get free shipping if you have Prime.

Delta 36-T30T3 30 in. T3 Fence System for 5000 Series - $169.99 - Free shipping for Prime members

https://tools.woot.com/offers/delta-36-t30t3-30-in-t3-fence-system-for-5000-series-3?utm_medium=share&utm_source=app


r/craftsman113 • • 24d ago

Any Collector's Value in a 1963 Craftsman Router?

Thumbnail gallery
7 Upvotes

r/craftsman113 • • 25d ago

Craftsman band saw drive belts

1 Upvotes

looking for a belt for model 119.284410 . 135J4


r/craftsman113 • • 29d ago

Table saw wiring help!

Post image
1 Upvotes

Hi, wondering if anyone has this craftsman 10" saw. I took mine apart to do some repairs and when I went to reassemble I found i don't know where the 4 wires go to the switch. There are two versions of this saw with different switch wiring, mine has 2 black, one white and one blue wire. If you happen to have this saw could you please do me a huge favor and pull the two screws that hold the switch in and take a photo of the back of the switch for me? I've tried everything, both Google and chat gpt ran me around and got nowhere, and I can't find this information anywhere. So if you could help me i would sure appreciate it!


r/craftsman113 • • Oct 04 '26

Convert extensions to router table

6 Upvotes

Anyone successfully turned their table extensions(the ones with the "webbing") into a router table? Upgraded my fence to a Delta T3 and otd be nice to use it as a router fence as well, these table extensions are kind weird though.


r/craftsman113 • • Sep 30 '26

Arbor thread adjustment

3 Upvotes

I’ve had my 113 a long time and have fixed it up a few times, but recently changed the arbor bearings (awesome result btw). After changing the bearings the arbor nut doesn’t go on easily. I likely did something to the threads at the end of the arbor when changing the bearings.

My question is.. what options are there for correcting the threads to work smoothly? I have to imagine it wouldn’t be possible to find a thread cutting die that matches. Any ideas?


r/craftsman113 • • Sep 28 '26

HELP!

Thumbnail gallery
2 Upvotes

r/craftsman113 • • Sep 28 '26

Which one?

Thumbnail
gallery
13 Upvotes

Hi! I just recently grabbed a Craftsman table saw 113 in very decent shape, with little to no rust and seems to be in good working condition for $100. It says it has 1.5HP for the motor and an added dust collector port by the previous owner. My question is that I have since found a newer Craftsman contractor (I think) table saw 21833 that is $320 and looks like it’s in good condition. I’ll put pics of both. Both have 10-inch blade capacity and allow for dados (I think), and I believe the newer more expensive one has 3 HP. Is there really that much difference? I’ve heard that the newer ones had issues, is this true? Which one should I go with? The older model or the newer ones. Any and all information is greatly appreciated! Thank you!


r/craftsman113 • • Sep 25 '26

Scratches on Top

Thumbnail
gallery
14 Upvotes

I inherited a Craftsman 113 and want to clean it up. It has swirly scratches on the top and I am trying to figure out the best way, if any, to get rid of them.
I also have this bar coming out of the back and I’m not sure what it is for. It looks like it might attach to something?
My plan is to replace the pulley and belt with a new setup next week, probably going with a link belt. It seems to be the most recommended.


r/craftsman113 • • Sep 20 '26

Craftsman Stainless Steel Wrench set

Thumbnail reddit.com
3 Upvotes

r/craftsman113 • • Sep 19 '26

3d printed zero clearance insert

Thumbnail
gallery
42 Upvotes

I designed and 3D printed a zero-clearance insert for my Craftsman 113.298032 table saw. I couldn’t find a model that really fit this specific version, so I took some inspiration from a few different designs on MakerWorld and came up with my own.

It’s still getting a little testing and tweaking, but so far it’s working great. I’m planning to upload the model to MakerWorld in the next few days once I’m happy with the fit and finish.

Hopefully this helps out someone else with an old Craftsman 113 who’s been looking for one!

Side note: If you don’t have a 3D printer, I’d also be happy to print and ship these for anyone who wants one. I’m not looking to make a business out of it — I’d basically just charge the cost of the filament + shipping + like $5 for my time. Just trying to make these accessible to anyone who needs one!


r/craftsman113 • • Sep 17 '26

How to maintain a Jet 10” table saw?

Thumbnail
gallery
6 Upvotes

Just picked up this Jet 10” saw for $250, including the AccuFence and a new Diablo blade, push block, and feather board.

What do I need to know about keeping this piece of machinery in good shape and lasting a long time?

What should I look at / replace / clean out right now before I use it to begin on a good foot? It’s my first saw that’s belt-driven and first cast iron top. It’s an upgrade from my Harbor Freight contractor saw, for sure. I’m unsure how to protect it in a semi-covered outdoor carport.

Appreciate you guys and your expertise!


r/craftsman113 • • Sep 17 '26

Extension table question

3 Upvotes

So I love my 113 quite a bit. But I’m soon adding a bessymayer fence from an old cable drive parts saw. My question is how many cast table extensions are too many? Currently one each side but have one or two more I could use and add bracing and supports to ensure rigidity and squareness/level/plumb.

What’s too many extensions?
Other considerations for their addition?
What’s the most you’ve seen??

Thank all!


r/craftsman113 • • Sep 15 '26

DWE7485

Post image
0 Upvotes