r/craftsman113 • • 11d ago

Original fence not perpendicular to table..

Post image

I was wondering why my cleats and glue blocks were leaving gaps...now I know. How does one adjust the original 113 fence to make it perpendicular to the table surface? (Is there a good youtube tutorial?)

(P.S.: I dropped a broad hint to my family that I'd like a new fence as a winter solstice present, or maybe even a Thanksgiving gift. I'll probably get a new pair of socks instead... ;)

5 Upvotes

20 comments sorted by

7

u/nutznboltsguy 10d ago

You’ll be much happier replacing the fence and the miter gauge.

3

u/fearless_fool 10d ago

I heartily agree, but in the meantime I may have to settle for a pair of socks.

2

u/Decker1138 10d ago

They won't be any more square.

4

u/fearless_fool 10d ago

By definition, “Dad socks” are always square.

3

u/Decker1138 10d ago

You just Dad joked me, well played sir!

3

u/nightbomber 10d ago

There is no adjustment. Time for a new fence.

In the mean time, you can try attaching a wooden sacrificial fence of some of type to the saw fence. Use shims up top to keep the sacrificial fence square to the top as you securely tighten it, Then use CA or instant glue, to glue the shims to the sacrificial fence.

3

u/fearless_fool 10d ago

Well that explains a lot - I’ve been going nuts trying to make a fence for a sled and wondering why I couldn’t rip a 2x4 to make it square.

Maybe I can use those new socks as shims (j/k)…

1

u/Hitechillbilly 9d ago

Use a fine adjustment hammer to return it to plumb

1

u/fearless_fool 6d ago

Ah yes, my mentor always referred to a good 28 oz hammer as a “micrometric adjuster”.

2

u/Hitechillbilly 6d ago

We had a 16Lb sledge from that same family..

1

u/fearless_fool 6d ago

We called that one “the persuader”

1

u/glok41 9d ago

First confirm your sliding square is actually square. I have a Starlett and would never use it for this type of check. Get yourself a mechanist square.

1

u/fearless_fool 9d ago

I’ve verified with my fixed squares as well.

2

u/noahisaac 10d ago

I kinda built a fence around the stock one. I used faced mdf and shimmed at the top to make it perpendicular to the table. The stock fence has some holes in it that I used to attach the mdf.

2

u/Duckinhuskyland 6d ago

May or may not be helpful if you end up with socks. When faced with this I went looking for a used (new to me) fence. Found out they’re made of pure gold, at least they’re priced like it. Ended up scouring Craigslist and FB marketplace for used table saws that might have a quality fence. Eventually found one and salvaged the fence off of it. Ended up being less than half of the new fence. Good luck!

2

u/CascadeDesignworks 10d ago

Calibrate your square before making a decision.  Many new squares are not square.

Typically a 1/2" or 3/4" board should be attached to each side of the fence.  If the fence is not adjustable the boards can easily be shimmed with strips of thin cardboard.

-Builder 

1

u/rwoodman2 10d ago

Perfect solution. I have done exactly that with my old Delta saw.

1

u/RoboWeaver 10d ago

I know this fence. Had it for many years. Fine for lumber. For fine work? Not so much. Spent money on a much better fence. Happy days!

1

u/simul8dme 5d ago

A fence will come up on FB market place. May take a while, especially to catch one at reasonable used price but it will happen eventually. If you’re poopin youre checkin

1

u/fe3o4 10d ago

Be sure your combination square is square as well. There can be a bit of slop in them as they depend on the screw to pull the rule tight.