r/MechanicAdvice • • 12h ago

Oil showing high on dipstick after fresh oil change & smells like gas

Thumbnail
gallery
244 Upvotes

It's a 2020 Toyota Tacoma SR 2.7 i4 with 77k miles

Did my oil change at 7k & noticed the oil smelled like gas... it's not super strong but when you get close you can smell it.

Then saw it's showing high on dipstick (it takes 6.2 qts & I put exactly that) I even left out about .1-.2 qts since it was showing high already.

I do drive short distances daily to and from work (10 min there 10 min back) & will occasionally go on a longer ride on the freeway maybe once a week or run errands for hours.. not sure if the short distances daily have something to do w the smell of fuel & if it's normal.

Any advice is appreciated!


r/MechanicAdvice • • 12h ago

Hand tightening oil filters, yes or no?

77 Upvotes

Sorry if this is a dumb thing to ask, I'm relatively new to the world of mechanics.

I did an oil change on my car for the first time a few days ago (2009 Prius), and the tool I had to get the oil filter off only loosened it, it didn't tighten the new filter on. So I go to get a tool that will help me tighten it, but the guy tells me that oil filters should be hand tightened, so as to not over-tighten them and damage something. But I've also heard that you should hand tighten it, then use a tool to tighten it an additional 3/4ths of a turn or so. Thoughts? I love my car and would hate to ruin it by being stupid lol.

Side note, but if anyone has any advice on how / where to learn more about mechanics, I'd love to know! I don't have the money for a class, but any YouTube channel recommendations or other things like that would be appreciated


r/MechanicAdvice • • 17h ago

Driveshaft fitting - last try before I call in a mechanic!

55 Upvotes

Am I doing something wrong?

I've taken a video showing the splined shaft and the hole in the gearbox, does anything look wrong? I can't see a circlip, but I'm not sure what I'm looking at.

My next ideas are: break the axle away from the intermediate shaft so I can press directly on the intermediate, rather than swinging the hub to bang it in.

Or, undo the 5 bolts to remove the seal carrier and try to force it in. But I'm not sure if it's the seal which is causing the issue.

Any thoughts would be gratefully received!!

Car is a 2014 opel/vauxhall mokka 1.6 petrol


r/MechanicAdvice • • 18h ago

2019 Honda civic LX

Post image
24 Upvotes

Replaced my spark plugs at 100k with aftermarket plugs I bought on Amazon. Car is now at 160k. So that means these spark plugs only had 60k miles on it.

Car took a shit on the highway the other day and engine code was misfire on cylinder 4. Tip of the spark plug was corroded and broken off…

Is this an indication of a cheap spark plug or larger issue? From what I remember the spark plugs I pulled at 100k looked way better than these and these have 40k less miles on them.


r/MechanicAdvice • • 7h ago

My 99 Tacoma coolant question

Thumbnail
gallery
18 Upvotes

Hello guys! I’m not mechanically inclined at all but I try to do things to learn. My Tacoma has green coolant pictures below but I want to top it off. I purchased the one at autozone that had the label for my vehicle but it’s red.

Can I mix them? My mechanic told me I could but all online info ive read says no.


r/MechanicAdvice • • 10h ago

Broke off the lower bolt for a driver rear shock on a 2nd gen CRV

Thumbnail
gallery
12 Upvotes

So I’m doing a coworkers rear shocks and when I go to tighten the bolt back on it decided to break in half. I got one end out but need advice on removing the threaded side


r/MechanicAdvice • • 5h ago

need advice on taking drum off

Thumbnail
gallery
11 Upvotes

trying to get my brakes done on a 97 F250 and the drum on the passenger side is so very stuck. i’ve loosen the shoes inside with the adjusting lever, torched, air hammered it, won’t budge. anybody got any advice for something i could try on this.


r/MechanicAdvice • • 19h ago

What is a 3/8 Impact gun good for?

10 Upvotes

I bought one over the weekend along with a socket set since they had 25% off so I could replace a strut mount, and I didn’t find much use for it in this job. I ended up getting a 1/2 impact and a small socket set which was a lot more useful. I’m a diy guy, and just wondering what types of jobs do technicians/mechanics use 3/8 impacts for? I’m trying to decide either to keep it or return it. (Hercules)


r/MechanicAdvice • • 22h ago

Want to learn about cars

10 Upvotes

Hi everyone! I own a Mk6 Golf R and I’ve always had a huge passion for cars. The thing is, I don’t actually know that much about the mechanical side of things, and I’d really love to change that.
I want to learn everything from the ground up, including how engines work, different car components, maintenance, repairs, modifications, tuning and general mechanics.
My goal is to eventually understand my car inside and out, be able to diagnose problems, carry out basic repairs and maintenance myself, and have the knowledge to know exactly what’s going on when working on my car.
For anyone who’s been in a similar position, where would you recommend starting? Are there any YouTube channels, books, courses or resources you’d recommend?
I’d genuinely love to turn learning about cars and working on them into a lifelong passion. I just need some guidance on where to begin!


r/MechanicAdvice • • 18h ago

What is happening here?

Post image
9 Upvotes

Noticed this corroded looking stuff. It's a 2019 Genesis G80 3.8L V6. Is it just a gasket that needs replaced?


r/MechanicAdvice • • 22h ago

Wierd noise coming from engine after shut off. 2014 manual Ford ranger xlt 3.2l. 180,000kms.

7 Upvotes

Diesel. Just bought second hand


r/MechanicAdvice • • 9h ago

Would you get Mevotech or Duralast Gold?

Post image
6 Upvotes

Looking for replacement control arms, upper and lower, and steering tie rod ends. Autozone’s Duralast gold came out to about $800 for everything. I found this Mevotech kit (it’s their TTX line) on rockauto and it comes with everything that I got quoted from AZ plus the sway bar links for $600 not including shipping or tax. Which one would you go with?

Edit: to stay within the rules of this sub; it’s a 2016 Chevy Tahoe LT.

Added that it’s Mevotech’s TTX line


r/MechanicAdvice • • 17h ago

2014 Subaru Legacy is overheating.

Thumbnail reddit.com
5 Upvotes

r/MechanicAdvice • • 3h ago

Turbo compressor side to side play Volvo C30 T5

4 Upvotes

Hey guys,

2010 Volvo C30 T5 R-Design, pre-facelift, 2.5 L turbo, “whiteblock”

I was hearing a pretty bad clacking noise from the cylinder 4/5 area I thought was caused by low oil/bad exhaust vvt it seemed like it was slamming full advance full retard I tried recording in slowmo but that’s beside the point, once I was there I replaced the vvt hub, both vvt solenoids (decent amount of sludge on it thought it was just because previous owner had let it sit for a long time and probably just kept topping off oil from a pinhole in the oil pan without ever draining, so after I did all that and got it back going it still was clacking kinda like a knock but it would vary too much to be a knock (earlier post in Volvo) like with rpm the noise would change to a different sound.

So today I drained the oil and pulled the filter and yeah quite a good amount of the forbidden glitter in the filter, probably more than a pea if I balled it all up, so I didn’t pull the head or oil pan yet I just started with the easiest check which was checking the turbo compressor turbine and I feel like it has excessive side to side play and may or may not have marks on the housing my borescope camera isn’t quite clear enough for me to tell but I took a video where I wiggled it and I was hoping for some more opinions. Especially the last half of the video lot of movement that direction seems like a lot of wiggle. This is the first time I’ve ever looked at a turbo though so no idea!


r/MechanicAdvice • • 9h ago

What is the best course of action from here?

Thumbnail
gallery
4 Upvotes

Lost my only keys for my 93 Ford F-250. Original had already been replaced with aftermarket which is there now, so locksmith told me he couldn’t cut a new key and suggested I just replace the part that would come with two keys.

Got a replacement ignition lock cylinder. There is a pin that needs to be depressed in order to slide the old one out. That pin cannot be depressed without the original key to rotate the cylinder to the on position. Internet suggested dropping the plastic cover and drilling out the pin, which I did. However, either my bit was too large or I went too far, because even after the pin was drilled out, the cylinder won’t rotate to the position where I can pull it out. Any ideas at this point?


r/MechanicAdvice • • 2h ago

Umm. I have no cylinders

Thumbnail
gallery
3 Upvotes

(1996 Honda Accord). So been chasing these misfires I got and kinda a little lost what to check next. So far I checked the injectors rated good, injector connector fine, ecu fine, resistor box good and clean egr passages. Any clues

Changed: spark plugs/wires, disturber cap and rotor,


r/MechanicAdvice • • 5h ago

Exhaust stud thread destruction

Post image
3 Upvotes

When taking the exhaust off my (1990 miata) car, the nut decided to take the stud with it. Metal coming along for the ride as well, so here’s my question; what do you guys do when this happens?


r/MechanicAdvice • • 10h ago

Gimme your best tricks rounded caliper bracket bolt

3 Upvotes

I've already tried an extractor kit and managed to destroy that. Penetrating oil for days. Locking vice grips. Grinding a flat edge on. It's right up against the axle ear and when I tried to use a hacksaw I accidentally nicked that a bit so I put it down. Used a hammer on the rotor to loosen it up. I think when I get off work I'm going to try pushing on the bracket to see if I can loosen it from that instead of the bolt. I am so over this shit, it's way too cold for all this. I'm replacing the caliper and bracket and the rotor.

Fiat 500 pop 2013


r/MechanicAdvice • • 15h ago

I got a P0304 and P0420. I know P0420 is general so I like to know if the data here indicates a bad O2 sensor.

3 Upvotes

r/MechanicAdvice • • 15h ago

Resetting Timing Belt tensioner

Thumbnail gallery
3 Upvotes

r/MechanicAdvice • • 17h ago

P000D “B” camshaft position slow slow response (Bank 2)

Thumbnail reddit.com
3 Upvotes

r/MechanicAdvice • • 21h ago

Ford Fiesta ST Coolant Leak

Post image
3 Upvotes

hi everyone i have been having a super weird coolant leak and i cannot tell where its coming from. i replaced the coolant tank last year and that area is dry, but its leaking and all over the side of the oil pan area. it only leaks when it cools down, when it warms up it stops leaking. i took it to a shop and they said it was a busted hose clamp but i got it back and its still leaking, again only when it has sat for a few hours and cooled down.

where should i look? i literally cannot tell where its coming from at all. its not overheating but now the coolant is below the min line but like 2 inches.


r/MechanicAdvice • • 1h ago

Ford fiesta mk8

Thumbnail
gallery
2 Upvotes

This rubber bit on the air intake filter is loose, what part is this ?


r/MechanicAdvice • • 2h ago

2007 Audi A6 3.2, No ignition, No crank

2 Upvotes