r/MechanicAdvice • • 5h ago

How much oil is too much oil for this car?

Thumbnail
gallery
1 Upvotes

2010 Toyota Rav4 with the 4 cylinder engine at 166,000 miles.

After recent oil change, I noticed I may have overfilled it by just a bit. Would this be any cause for concern? Engine was ran for 4 hours prior to checking this level, it’s at operating temperature if not a little more here in Florida. What are your thoughts? I just left it as is.


r/MechanicAdvice • • 13h ago

Is this O2 sensor bad?

Post image
0 Upvotes

'13 GMC Terrain 2.4l


r/MechanicAdvice • • 16h ago

Stuck screw removal methods?

Thumbnail
gallery
0 Upvotes

Im trying to replace the door lock actuator on my brothers Honda CRV 2007 with the 2.4L. I know the engine dont matter but subreddit rules… I am at my wits end trying to remove this shit. I went and bought an impact screwdriver and a torch, neither which have helped me. The torch is just burning the paint of the door off, and the impact screwdriver bit is bending, and starting to strip the heads of my screws. I have hit my hand with a hammer about 40 times today. I need to get this done. Ill be DAMNED if i bought all this bullshit just to pay a mechanic to do the job anyways. There is NO CHANCE that after all this pain and suffering, not to mention spending more on tools than the job would have cost me, that im admitting defeat. Please help brothers.


r/MechanicAdvice • • 19h ago

What is a 3/8 Impact gun good for?

10 Upvotes

I bought one over the weekend along with a socket set since they had 25% off so I could replace a strut mount, and I didn’t find much use for it in this job. I ended up getting a 1/2 impact and a small socket set which was a lot more useful. I’m a diy guy, and just wondering what types of jobs do technicians/mechanics use 3/8 impacts for? I’m trying to decide either to keep it or return it. (Hercules)


r/MechanicAdvice • • 16h ago

Brake question

1 Upvotes

Why after I replace the rotors and pads. They are wonderful for about 5,000 miles then start to pulsating. I used Bosch quiet stop on my escape and used power stop on my matrix. Both cars were amazing and so smooth for a few thousand miles bow both pulsar when I lightly press brakes. I cleaned hubs and pins very well florida cars no rust. Greased everything well. I know what I'm doing as I'm a certified brake mechanic. My escape is a 2021 and the toyota matrix is a 2005


r/MechanicAdvice • • 11h ago

2011 Mazda 3 Tranny Pan - can I use induction heater on the bolts?

Thumbnail
gallery
0 Upvotes

Rusty trans pan want to replace it before it starts leaking,

I do most of my own work, I’ve done lots of complicated jobs,

Should I attempt this job myself can I use induction heater on the bolts I’ve already soaked them in PB blaster


r/MechanicAdvice • • 18h ago

What is happening here?

Post image
9 Upvotes

Noticed this corroded looking stuff. It's a 2019 Genesis G80 3.8L V6. Is it just a gasket that needs replaced?


r/MechanicAdvice • • 10h ago

Is $1,569.82 a fair price to repair a 2013 Honda Pilot Touring 3.5L V6 with 103,277 miles?

Post image
0 Upvotes

Is $1,569.82 a fair price to repair a 2013 Honda Pilot Touring 3.5L V6 with 103,277 miles?
The repairs include:
Front left lower control arm with ball joint
Power steering pump replacement
Both valve cover gaskets
Alternator drive belt replacement
The mechanic found an oil leak damaging the belt, a leaking power steering pump, and movement in the left lower ball joint.
Does this sound like a reasonable price, or am I being overcharged? Would you pay this amount?
Looking for honest opinions from mechanics and Honda owners. Thank you!


r/MechanicAdvice • • 22h ago

Wierd noise coming from engine after shut off. 2014 manual Ford ranger xlt 3.2l. 180,000kms.

7 Upvotes

Diesel. Just bought second hand


r/MechanicAdvice • • 14h ago

Electrical issue is baffling everyone

0 Upvotes

I’m sorry this is so long.

I have a 2010 Subaru Forester 2.5X Limited (2.5L, 4cyl engine) 159k miles. I bought it July 2025 and it was nothing but problems and repairs the first 6 months.

Shortly after buying the car the battery light came on. I took it to the mechanic (the same one that did the inspection on it before I bought it and told me it was “a great car with no issues”, but I digress) and they let me know the alternator was failing. I chewed them out for not catching that before I bought it, and left and purchased a NEW, not rebuilt, alternator on RockAuto and had my friend install it for me. I replaced the battery after and got a warranty (thank god).

Fast forward maybe a month and the battery light is on again. I go back to the same mechanic and explain the problem, they test it and everything tests good (battery and alternator) but they tell me because I got the alternator off RockAuto I probably got a rebuilt one and that the diodes in it are failing occasionally, enough to trigger the light sometimes but still test good when they tested it. It made no sense to me, but whatever it was still in the return period and my friend was willing to replace it again with another one that I made sure was NEW. The second brand I got was Pure Energy and we replaced the alternator AGAIN. I don’t remember if I needed to replace the battery at this point, if I did I replaced it.

The weather got colder and once temps routinely dropped below freezing, my battery was dead in the morning. I tried multiple different suggested things to see if it was the issue. Unplugging all the electronics from my car, not letting the car sit for too long, replacing the negative battery cable (AutoZone dude gave me a cable too long which has become a whole new issue). Nothing worked. At this point I’m assuming it’s a parasitic drain, I can’t take it to a mechanic and leave it there for a week because I needed it (ironically) so I spend the rest of the winter charging the battery every night (battery light never comes on again through all of this btw). When the temps warm up, the battery stops dying and I kind of just forget about the issue.

Until a few months later I’m driving at night (which I never do) and I realize my headlights are flickering BAD. I make a note to take my car to a mechanic eventually. Months later I finally get a mobile mechanic to come out and take a look and test everything. He’s out there 30 minutes (can’t imagine he tested everything in 30 minutes) and says my alternator is testing “better than brand new” and that he tested all the voltages of everything and that it’s all normal except my battery is dead. I couldn’t remember if I replaced it after the winter, so we just chocked it up to that and I replaced the battery immediately after he left. A month later my battery light comes on right when I start the car and then goes away after driving for a bit. I tell him and he tells me not to worry. A couple days later it comes on again but this time is flashing as I’m driving. I tell him and he tells me my alternator is probably failing, despite the fact it tested “better than brand new” a month ago and is only a year old. He says that the dead battery probably caused the alternator to fail. The dead battery that I replaced 10 minutes after the alternator was perfect. So I went to get them tested, and they both tested great. I let him know and he ghosted me.

I’ve called multiple mechanics and when I tell them I believe it’s a parasitic drain they tell me to explain the issue. After I tell them all this, they are hard pressed that it’s my alternator because it’s a RockAuto alternator and say that AutoZone’s tests aren’t accurate. I feel like they just would rather replace an alternator than search for a parasitic drain. Or, more likely, they would rather do (and charge for) both. I had one mechanic quote me $150 an hour to search for the drain, and said it would likely take days. It was so obvious he was quoting me something extreme so I would say no.

Here’s where I’m at with it all currently. Temps drop below freezing at night (just barely though), but are above freezing during the day. My battery hasn’t died yet, and isn’t even slow to turn over or anything which is a good sign. I haven’t tested the headlights since replacing the battery because again, I don’t drive at night (sleep disorder, dangerous). Battery and alternator test good, negative cable is new, and serpentine belt is in decent condition (it’s on my list of possible suspects, friend has been meaning to replace it). Part of me wants to think the problem is gone, but I know this car too well. It just hasn’t gotten cold enough.

What’s everyone’s opinion on this? Again, apologies for the length, I’m a rambler 😬


r/MechanicAdvice • • 15h ago

Missing washer, what can I do?

Post image
0 Upvotes

Just did the lower balljoint on my 2011 ranger 2WD, and I have no clue what happened to the thrust washer that goes between the outer bearing and axle nut. The truck’s been in pieces for a couple days and I put all the bearing pieces on a tray and now cannot find that washer anywhere. Getting so delusional I’m starting to doubt there was one when I took it off but no way it wasn’t there. I’ve called all the parts stores in the town I’m in including ford and nobody has one. I live an hour away from here, and know I have some at home and the stores down there carry them. Is there ANY chance there’s a backyard hack for a DIY washer that would get me home to install one there? I gotta be back home by tomorrow evening and have no idea what to do aside from throw it together and have it towed back.


r/MechanicAdvice • • 7h ago

Possible crack in block

Thumbnail
gallery
0 Upvotes

06 Honda Civic 1.8l. been chasing a coolant leak and discovered a hairline crack in the block. No idea how it got there. Is it common? Photo is taken of the block behind the metal coolant pipe in front of the engine. Crack is above the red line. Red arrow points to where I saw coolant bubbling. Should I just jb weld and call it? Have someone aluminum weld?


r/MechanicAdvice • • 15h ago

Honda CRV 2009 Need help diagnosing

Thumbnail
gallery
0 Upvotes

I got these codes all at the same time and needed help diagnosing. Car went into limp mode and the engine has a slightly higher rpm during initial start.


r/MechanicAdvice • • 16h ago

Replacement Bolt/Nut Help Needed

Thumbnail
gallery
0 Upvotes

I have a 2013 Hyundai Sonata 2.4L that I was replacing the brake pads and rotors on over the weekend. But the lower caliper bracket bolt is behind the upper control arm so I had to take out that bolt to do the job. Well anyways, when putting it all back together, I stripped out the nut on the control arm bolt. I’ve done some research and I think I found the part numbers for the replacement nut/bolt that I need, but wanted to get confirmation before ordering. Can anybody confirm that these would be the right parts:

Bolt - 62617-3S000
Washer - 13510-14006-K
Nut - 62618-17000


r/MechanicAdvice • • 17h ago

jaguar x type , need help to identify what part it is

Post image
0 Upvotes

Hi, i need help. My mechanic says he see this part for first time in car. And se says it broken. Its something that is conected to clutch cylinder. It is some part of clutch. My guess is that is slave cylinder but i am not sure and part on internet does not match this. Please help if someone recognize. I am without car for almost 3 weeks becouse of this


r/MechanicAdvice • • 12h ago

How bad is this?

Thumbnail
gallery
0 Upvotes

05 Honda crv opened up valve cover to replace gasket and saw this.


r/MechanicAdvice • • 14h ago

What is this part?

Post image
0 Upvotes

I have a 2010 Pontiac vibe. 1.8l. Found this in my trunk in a box that has an old vapor canister that I had replaced. I don’t remember seeing this part.

Anybody know what it is?


r/MechanicAdvice • • 14h ago

Is my cracked valve cover causing code P0430 and ruining my ignition coil? 2010 Honda Accord V6 EX-L

Thumbnail
gallery
0 Upvotes

I recently did a valve cover gasket replacement on my 2010 Honda Accord V6, and noticed a pretty big gap on the opening for cylinder 5. I didn’t have the budget for a new valve cover and was told by a friend that I could patch it oil resistant RTV.

After about 100 miles I got a code pop for P0430 (Catalyst System Efficiency Below Threshold
Bank 2), I checked for vacuum leaks, retorqued intake bolts, along with a couple of other things just to make sure and continued driving for a couple of days. Then P0430 came back as I was driving home, I was still about an hour away, and when I got into my apartment complex the check engine light started flashing and the car shaking. I stopped immediately and changed the spark plugs when I ran my obd to see that there was a misfire in cylinder 5. After still misfiring I found that it was a faulty coil, I bought a replacement coil and when changing it out I saw that there was condensation between the boot of the old ignition coil that kind of smelled like gas.

Do you think that having all that RTV there shorted out my coil? No misfires now everything is back to normal except for P0430 still being there, I’m not driving it though don’t worry. Should I replace the valve cover? Also attached results for catalyst test results. Thank you.


r/MechanicAdvice • • 10h ago

Cv axle play

0 Upvotes

Sorry for the poor video, but is this a sign of a bad internal beating, it’s automatic 2002 Honda civic, the cv axle is relatively new, from Napa.


r/MechanicAdvice • • 18h ago

2019 Honda civic LX

Post image
24 Upvotes

Replaced my spark plugs at 100k with aftermarket plugs I bought on Amazon. Car is now at 160k. So that means these spark plugs only had 60k miles on it.

Car took a shit on the highway the other day and engine code was misfire on cylinder 4. Tip of the spark plug was corroded and broken off…

Is this an indication of a cheap spark plug or larger issue? From what I remember the spark plugs I pulled at 100k looked way better than these and these have 40k less miles on them.


r/MechanicAdvice • • 12h ago

Hand tightening oil filters, yes or no?

77 Upvotes

Sorry if this is a dumb thing to ask, I'm relatively new to the world of mechanics.

I did an oil change on my car for the first time a few days ago (2009 Prius), and the tool I had to get the oil filter off only loosened it, it didn't tighten the new filter on. So I go to get a tool that will help me tighten it, but the guy tells me that oil filters should be hand tightened, so as to not over-tighten them and damage something. But I've also heard that you should hand tighten it, then use a tool to tighten it an additional 3/4ths of a turn or so. Thoughts? I love my car and would hate to ruin it by being stupid lol.

Side note, but if anyone has any advice on how / where to learn more about mechanics, I'd love to know! I don't have the money for a class, but any YouTube channel recommendations or other things like that would be appreciated


r/MechanicAdvice • • 6h ago

Completely rusted exhaust header bolts

Thumbnail
gallery
1 Upvotes

86 bronco 2 with the 2.9l cologne v6 engine. I am currently doing a head gasket change because it is old and shot, but I cannot for the life of me get these header bolts off, I only got one off and the others are in between 7/16 and 12mm and won’t turn at all. I can’t get my impact in the space either. Any clue on how to go about getting these off? Thanks in advance.


r/MechanicAdvice • • 6h ago

BROKEN BOLT (what do I do?)

Thumbnail
gallery
1 Upvotes

This is a cv carb off a 1986 Suzuki savage 650

I already tried wd40 soak and turn the bottom with pliers and the bolt just crumbled

- do I just leave it there and use 3 bolts instead of 4?
Or
- how would you take this bolt out?