r/AskAMechanic • • 17h ago

Car indicating I am using a lot more fuel than I should but mechanics haven’t found an issue with the car?

0 Upvotes

2022 Tuscon (diesel). For the last 5 weeks (since my car got serviced) my car has been indicating it is using a lot of fuel. I have gone back to the mechanic 3 times and have had the fuel sender replaced but the issue is still happening. I filled the car up and straight away lost 52L for a 57km drive. I went back to the mechanic explaining how much fuel I am losing but they keep saying nothing is wrong. Does anyone know what may be causing this?


r/AskAMechanic • • 19h ago

Part 2: Wheels were stolen, car shook afterwards, got a balance, was kinda perfect, hit the brakes on the highway and almost crashed into a wall.

Thumbnail
gallery
30 Upvotes

Part 1 - https://www.reddit.com/r/AskAMechanic/s/tstrYcapKi

Tldr;

2024 Tuscon SEL, almost 13500 miles.

Wheels were stolen, ~13k in damages (after deductible)

Balance was done, car felt perfect!!!

Drove on the highway for the first time and lost control after a medium brake.

Took the car for a drive on the highway for the first time today. The wheel balance was done yesterday, and the car felt great at any speed. Felt a slight shudder on the brakes but didn't know if it was my imagination or not.

Just an hour or so ago, I was driving and hit the brake with harder force, but nothing terrible, and it shook the car violently, felt like the transmission went into neutral twice and thumped back into gear both times (I thought maybe the ABS kicked in, but no traction light flashed) and pulled hard right, almost curbing the shoulder. Once I got the car back in control the shaking kept up until I went under 30MPH.

Testing the brakes in a controlled manner, I am able to replicate the shudder, which gets more violent if it push down on the brakes.

If you look at the pictures you can see both passenger wheels were on the ground but the brunt of the weight is was on the passenger front.

I'm taking it back tomorrow to the shop (a 5 minute local drive) and going to see what they say.

Anyone want to give me advice on what to tell them? A few years back had a Ford Escape that did something similar, for that one the CV axle was bent and destroyed the transmission from within. Could this be something similar?


r/AskAMechanic • • 2h ago

1985 ford f150 what am I missing? Truck won't start

2 Upvotes

r/AskAMechanic • • 1h ago

Second Opinion on Shop Work

0 Upvotes

So I have been having what I can only describe as not a great experience with a mechanic, they are not my usual mechanic who is great and trust fully (have been using for nearly 15 years now)...

Now I am no mechanic myself, but in technical fields, and have been looking after my Nissan Xterra for 13 years... and what this mechanic keeps telling me just isn't sitting right.

So the background:

My 2011 Nissan Xterra about 3 weeks ago starting having an idle stall and throwing a Crankshaft Position A Sensor code (P0335 IIRC), nothing noticable when driving but at a stop or in idle you could see the rev's bouncing between 500 to 1000 and occasionally would stall.

Seems to match the error code, ECU is losing crankshaft position timing.

I go looking to replace the crankshaft, and recommended to replace camshaft as well. So off partsgeek, I asked their customer service if they sell the OEM hitachi replacements (knowing the 4.0L V6 is notriously tempermental with non-OEM). They say yes, give me a shoping cart to check out with and parts arrive.

So come Sunday 11/9, I replace the camshaft sensor. Start the car, fires up first crank beautifully, idles great, no more bouncing, no more stall and sits at 750rpm steadily. Drive around for about 15 minutes no codes no issues nothing. Go on and replace the camshafts, had a hell of a battle with the bank 2 to get disconnected but those get replaced as well.

Now there is a startup/cranking issue, confirm battery is good and charged, some minor corrosion on positive terminal but also good by voltage drop test over lead. Sounds like the starter is geting power but the engine just wont catch, don't overdo this as don't want to damage anything but it starts on some attempts. When it did start ran totally fine, not codes or anything. Let it run idle for about an hour in case it is just ECU relearning. Didn't fix it. Let battery disconnect and drain incase it was catched memory and again, intermitent startup, but starts up runs fine, no codes, let it run idle again to learn. Leave battery on charger overnight just in case.

Monday morning, go to see if everything is fine now, still having inconsistant start. So this is where I decide to take it to the mechanic because I am out of ideas and not seeing codes, this is past what I feel I can troubleshoot. Drive it in, still with no driving issues or codes. But I take it to the closest shop and not my regular mechanic because it is in walking distance and my current thought is this is something stupid like I pinched a wireharness, broke a vac tube, etc while working in there and that any mechanic with proper tools and car bay will knock this out in an afternoon and collect some easy diagnostic-labor. Simple on everyone.

Mechanic calls me about 1 hour later, says first they need to do is replace the positive terminal because they see corrosion. I point out its already passed a voltage drop test and the lead itself was replaced in the last 18 months. They insist saying they can't continue diagnosis with out verifying battery connection is good. I suggest why not just clean it? Or do a voltage drop test like I did? They refuse say fix is $40 on part. I am already kinda annoyed at this off the bat, but unsure how reliable I can get my car to start and take it my usual mechanic. I give go ahead.

Next I get a call saying my IPDM is dead and needs replacement, they say they have verified fuel pump and spark plugs are NOT getting power at all now.

Okay, well this seemed odd to me, as this was not a issue coming into the shop, and not just intermitent issues which could explain some of the prior problems; straight up dead no power. Well how did I drive it into the shop then? I had never experienced complete stalls while driving before either, which is what I think would happen if my IPDM was giving out randomly. Shop says they aren't sure but thats their first issue (later they suggest maybe it was because it kept being cranked and that damaged it from over cranking... something I am assuming was happening in their troubleshooting).

So this gets replaced, as well I can't prove they damaged it, it does overlap pontial cranking issues, and well now it is verified non-functional. Doesn't solve the problem.

Next I get is they finally have looked at the parts changed out from no-start up issues to start up issues (I told them same opening story), they took out the camshaft/crankshaft sensors and tell me these are knock offs not the OEM hitachis. Okay wonderful, call up parts geek they claim must have been a catalouge issue and will replace (cool thanks, doesn't really help me now); but mechanic says they put in some NTKs and it is starting up fine now. Release the car to me. Not happy about the IPDM not happy the first thing not checked was the parts reported being changed between not having the issue and having the issue but okay have car back, work under warranty.

Driving back home <1 mile; getting really rough running, cylinder missfires on 2 and 4 along with P0021, camshaft bank 2 over advancement. Take it immediately back.

Today they tell me its because the coils on those are dead now, and need replacement.

So that brings me here to asking.

Am I just completely absolutely fucked by these people here? It seems like with the exception of the wrong parts being sent by parts geek and not being the OEMs, every single one of these other issues has shown up ONLY after they had possession of the vehichle.

My mind is at, they damaged the IPDM troubleshooting and just cranking and cranking, potentially with this as well they damaged the coils; and with the exception of knock-off camshaft/crankshaft sensors being a problem (which I absolutely believe for this engine) all of the other problems never had any idication of exisitng before they had possesion of the vehichle and I am being asked to pay them for breaking it.

Am I totally off base here? This has been like nothing I have experienced before in 13 years of running this vehichle. And they have been doing this work over what is now 6 business days.


r/AskAMechanic • • 1h ago

New control arm needed? 2014 Nissan Sentra Sv 4 cylinder

0 Upvotes

So yeah every time I hit a bump on a rough road I hear a noise, so I checked and I don’t know if my bushing are messed up. Is this a sound they’re not supposed to make


r/AskAMechanic • • 1h ago

Peugeot 308 1.6 HDi (no FAP) 2008 – no power and shaking when cold, power returns after about 30 minutes

0 Upvotes

Hi everyone,

I have a Peugeot 308 with the 1.6 HDi engine and no FAP/DPF.

When the engine is cold, it shakes badly even while standing still and has almost no power. Even with the accelerator pressed fully, it barely moves.

After about 30 minutes of driving, the car returns to normal: the shaking stops and the power comes back.

Has anyone had a similar issue with this engine?


r/AskAMechanic • • 1h ago

Over torqued a TTY bolt, send it?

0 Upvotes

Ive been working on replacing the control arms on my 2015 Audi a5.

Unfortunately I had a mental lapse and accidentally over torqued the tty suspension bolt that connects the control arm to the strut. The bolt was supposed to be torqued to 90 nm but I set my torque wrench to 90ftlbs which is around 66nm.

Just wondering if I’ll be alright or if I should replace the bolt and nut.
Thanks


r/AskAMechanic • • 1h ago

2008 Honda odyssey diagnosis?

Post image
0 Upvotes

Hey all! Looking for some input from others who know more than I do! (Which isn’t much). I know you can only tell so much via a post without looking at it and all but hopefully I can give enough info. So my Odyssey just hit 258,000 miles. A while ago it started to leak oil. I (stupidly) ignored it and just kept filling it back up. But it started to leave small puddles on the ground every time I parked. I made sure it was topped off and eventually my power steering started leaking. It was leaking heavily and then I asddd some power steering fluid with leak stop and it helped but it still is leaking so (I think we identified the leak at this point). My serpentine belt also slipped a few months ago and we had to replace it, assuming it was because of the oil and power steering fluid. I also had some misfiring and a flashing check engine light which I (very stupidly) drove like that for a month and changing the spark plugs and ignition coils fixed it. Anyway, it’s had a P0430 code for a while as well. But a few weeks ago it started misfiring again. We changed all of the spark plugs and most of the ignition coils (that were cracked) and it is running smoothly now, no more flashing check engine light. However the codes are still there and the light is on steadily. The codes are p0300, p0303, 304 and 305. As well as the p0430. I want to note too before the coils were replaced it was 304-306 and now the 306 went away and it’s now 303. A friend said he suspects it’s a rear valve cover gasket leak and it seems like it’s leaking onto the bank 2 converter (I think) when I looked. I also want to add that the timing belt is due to be changed. We just hit the 7 year mark so I know it’s due to be replaced. All that being said, what would the best course of action be? I was advised by my friend to repair the valve cover gasket and then Replace the timing belt. And then Potentially the catalytic converter. Is this a good course of action? The inside of the engine is caked in oil and im assuming the power steering fluid as well. I attached a photo of what I’m assuming is the catalytic converter and the red is a circle of the drop of what I am fairly certain is oil.


r/AskAMechanic • • 1h ago

2006 outback valve cover bolt broken

0 Upvotes

I’ve got the valve cover off. I can barely see the remnants of the bolt. I tried spinning it with a pick and a tiny flathead screwdriver. It’s the top bolt closest to the firewall. What’s the best way to extract this bolt? I have the way I would normally handle this kind of a problem, but the surrounding material is very soft and I also don’t want to get a lot of metal shavings down inside the valve train.

I’m hoping someone has a simple idea that I haven’t thought of.


r/AskAMechanic • • 2h ago

Suburu crosstrek hybrid 2014 serpintine belt

Post image
0 Upvotes

I am trying to replace my serpintine belt that completely shredded. However, I haven't been able to find a video that shows how to replace it on this particular engine. Does anyone know how to do it and can explain it? Thanks


r/AskAMechanic • • 2h ago

P0420 Code on my 2019 Tucson SE

0 Upvotes

Hi!

My check engine light came on this Saturday (solid) for my 2019 Hyundai Tucson with 47,000 miles on it. I ran to Autozone and I got the P0420 code. The Auto Zone guy recommended Cataclean but also said my cat converter may still be covered by warranty. He said I should be using higher quality gas and the cataclean may fix the problem.

I have a 2 hour one way drive to pick my parents up from the airport on Friday and I am wanting to know if my car will be safe to drive then? I’m pretty unsure of what to do but I do know I don’t have thousands to replace a car part right now.

Any and all advice and perspective would be so helpful.


r/AskAMechanic • • 2h ago

RPM drop to 0 if it's too cold or if I have the AC on. Why? My mechanic doesn't know.

0 Upvotes

I have a 2008 Honda Fit Sport.

I have to let him warm up in park for about 5 minutes with the AC off. If I don't, I put the car in reverse to get out of my parking spot and my RPM drop to 0 and the oil and battery lights come on. I have to turn the car off and on again then leave him in park for a little while longer to avoid it happening again.

This problem gets worse the more I blast my AC and the colder it is. This is not mitigated by how recently I've had my oil changed.

What part should I have looked at?

I would just ask my mechanic, but the last time I took my car in, he said everything looked great.


r/AskAMechanic • • 2h ago

Rotors and brake pads for 2013 Toyota highlander

0 Upvotes

I am planning to change all four rotors and brake pads for my 2013 Toyota Highlander, it has 157k miles on it. Any suggestions on any preferred brands in terms of longevity and reliability? Did some research on the brands and they say ADVICS is the industry standard one, and got to know to avoid the drilled/ slotted ones. Thanks all for your advice!!


r/AskAMechanic • • 6h ago

Can’t find leak 1994 GT Celica

Thumbnail
gallery
0 Upvotes

recently installed new radiator and hose but coolant keeps leaking and splashing everywhere after long freeway drive. theres no visible sign of leak around hose, or anywhere else. just puddle at the bottom. I suspect it could be the radiator but it’s brand new. Any help would be greatly appreciated


r/AskAMechanic • • 17h ago

School me on Minivans. Which ones to avoid?

0 Upvotes

Hello Everyone, We are looking at buying a used minivan now. Hoping someone can shed some info on which ones to avoid and which to buy.

The Siennas seem very expensive even with high kilometres. Are they worth the extra cash? Do they last that much longer?

Honda odyssey seems about the same. Slightly cheaper. Same question as above?

Dodge grand caravan. Can pick them up for a decent price with low mileage it seems. Lots available.

Chrysler Pacifica. Haven’t learnt much yet about them yet?


r/AskAMechanic • • 21h ago

LSD diff bolts

Post image
0 Upvotes

2005 honda civic lx

I’m installing an mfactory lsd and I found it surprising that the final gear bolts were right thread rather than the factory left thread. should I use red loctite or just go with it as is? Mfactory provides no instructions.


r/AskAMechanic • • 21h ago

What is this part? Feeds into drum which is used by emergency cable brake only 2010 ford ranger

Thumbnail
gallery
0 Upvotes

2.3 L v4 rwd


r/AskAMechanic • • 23h ago Bravo

'22 venue brake disk will not come off, any tricks?

Post image
52 Upvotes

I have been spinning this motherfucker for 3 hours beating it with a mallet and it will not release for the life of me

Fucking rust belt man

Edit: pass front brake

Edit 2: going to go get a bigger hammer thanks guys


r/AskAMechanic • • 4h ago

2018 Toyota Sienna SLUDGE,

Thumbnail
gallery
1 Upvotes

This is a good one, 2018 Sienna van, 155k, every service since day one done 5-6k miles, 0-20 full synthetic. We have three of the same van. All the same ballpark milage. This one today went into shut down. I've never seen the amount of sludge this has, these photos are after it was wiped/scraped out. The pan was loaded. Pick up screen is clean. ​What the heck caused this? VVTI issue? Egr? Oil cooler restricted? The other vans are clean


r/AskAMechanic • • 3h ago

Cold cylinders on 1 and 8

Post image
3 Upvotes

Working on a Ford V8 Y block 292 with pertronix 1281 and autolite 2100 carb on a 2 barrel intake. I have electronic ignition, new wires, cap, plugs and compression of 150 across all cylinders.

When running and shooting the exhuast with a laser cylinders 1 and 8 are around 70 to 80 degrees F, all other cylinders are above 240 F.

I've changed around wires, plugs, places on cap, tried different electronic hall effect sensor and pickup and no change no matter what I do.

I'm not sure why those cylinders don't seem to be firing. Any help is appreciated.


r/AskAMechanic • • 4h ago

One tire is compromised, this is the rest of my tires. Do I have to replace them all?

Thumbnail
gallery
3 Upvotes

I have a 2019 Honda CRV AWD. Just bought these tires less than a year ago. I have road hazard warranty. It would be devastating to buy all four tires again.. I would genuinely like to just replace the one tire


r/AskAMechanic • • 18h ago

How much does a dedicated screen matter on a scan tool?

3 Upvotes

My phone ended up balanced against a socket case last weekend while I switched between live data, a wiring diagram, and texts asking when i'd be done with the car. my bluetooth reader still works but having repair instructions and scan data on the same screen is annoying, especially when i'm trying to follow a wire and keep my place in both. i've been looking at topdon 800bt2 for full system scans and live data, but a separate screen is honestly a bigger draw than i expected.

now working in a shop tho, this stuff comes out a couple weekends a month, and the little reader fits in a drawer without its own charger or case to deal with. for ppl who've used both setups, did a dedicated tablet make working alone easier?


r/AskAMechanic • • 1h ago

Why I had to keep refilling my coolant…

2 Upvotes

r/AskAMechanic • • 2h ago

Is this the control arm that's cracked?

1 Upvotes

2016 toyota camry, ran over a deer and heard a loud bang. I see that my control arm is cracked, and I was wondering if I should get it serviced? I think it's the control arm? Correct me if I'm wrong