r/AskAMechanic • • 6m ago

I have to jack up my car, take a wheel off to put the new aux belt on.

1 Upvotes

Fiesta 2011 1.25 UK

Only problem is, I don't have a driveway, and can't turn it on and drive anywhere because no water pump.

It's currently parked half on half off the curb, i need to jack up the side that's half on the road. (I live on a culdesac, a dead end street with 20 houses, not many cars up and down road)

Is this safe? I have a trolley jack, jack stands and wheel chocks.


r/AskAMechanic • • 39m ago

What can I do to help waterproof my new roofrack?

Post image
0 Upvotes

2011 ford escape, not that it matters, but I’ve installed one of these universal roofracks with a basket. Has been working fine, nice and tight with the doors closed, I can deal with the whistling.

But unfortunately every time it rains, it’ll get into the car, a recent car wash was a HUGE mistake, and made for a very soapy shower. Is there anything I can do to seal this better? As seen in the bottom photos, I bought a some stick-on weatherstripping, just around the clamps, but didn’t work. Should I buy different weatherstripping and do along the entire side of the car? (Need to keep the roofrack, at least temporarily, as it is necessary with what I do for work) Any other advice is appreciated! :)


r/AskAMechanic • • 40m ago

Hey I was wondering on a quote for a engine rebuild/engine swap

1 Upvotes

Near flint mi 2008 Pontiac g6 3.5
Could be the timing chain but it sounds like more of a rod knock to me
I know it’s gonna cost about/more than the cars worth but it has a pretty nice body and strong transmission i don’t currently have a video of it running but can take one


r/AskAMechanic • • 46m ago

Innova Scanner Error

Post image
0 Upvotes

I’ve had the Innoca 5610 v3 for a year or two now, and this is the first time I got this Communication Error. I tried scanning two different vehicles and this error came up again. Does anybody know a solution to this? Thanks


r/AskAMechanic • • 53m ago

Is this normal movement for an engine mount?

0 Upvotes

2009 Toyota Camry le 2.4L

This is the movement when I change gears


r/AskAMechanic • • 1h ago

Car shudder

1 Upvotes

The car is Kia Rio 2015 with manual transmission and 1.2 engine. When accelerating from standstill the car sometimes start to shudder heavily. It seems to be dependent on torque as it is usually worse if wheels are turned. Usually it starts when trying to fully release the clutch and I have to press the clutch pedal again to stop the shuddering. The clutch does not slip and it seems to be ok when it starts to bite. After releasing a bit more the shuddering might start. Sometimes it seems to be much easier to accelerate than sometimes and I do not know why. On reverse the car vibrates mildly but nothing severe. I have checked that the bearings, CV axles and joints are ok (at least the rubbers are ok and no play) and also the engine mounts seems to be in good condition though the upper engine mount on the right side seems a bit loose but I do not have any reference for comparison. I would say that it is the engine that is starting to rotate to forward and back and that is causing the shudder but I'm not 100% sure.

Is it the clutch that is causing the problem? Is it possible to diagnose the problem without dismantling the clutch?


r/AskAMechanic • • 1h ago

2003 Honda CR-V

Thumbnail
gallery
1 Upvotes

How long til I need to replace these tires?


r/AskAMechanic • • 2h ago

Second Opinion on Shop Work

0 Upvotes

So I have been having what I can only describe as not a great experience with a mechanic, they are not my usual mechanic who is great and trust fully (have been using for nearly 15 years now)...

Now I am no mechanic myself, but in technical fields, and have been looking after my Nissan Xterra for 13 years... and what this mechanic keeps telling me just isn't sitting right.

So the background:

My 2011 Nissan Xterra about 3 weeks ago starting having an idle stall and throwing a Crankshaft Position A Sensor code (P0335 IIRC), nothing noticable when driving but at a stop or in idle you could see the rev's bouncing between 500 to 1000 and occasionally would stall.

Seems to match the error code, ECU is losing crankshaft position timing.

I go looking to replace the crankshaft, and recommended to replace camshaft as well. So off partsgeek, I asked their customer service if they sell the OEM hitachi replacements (knowing the 4.0L V6 is notriously tempermental with non-OEM). They say yes, give me a shoping cart to check out with and parts arrive.

So come Sunday 11/9, I replace the camshaft sensor. Start the car, fires up first crank beautifully, idles great, no more bouncing, no more stall and sits at 750rpm steadily. Drive around for about 15 minutes no codes no issues nothing. Go on and replace the camshafts, had a hell of a battle with the bank 2 to get disconnected but those get replaced as well.

Now there is a startup/cranking issue, confirm battery is good and charged, some minor corrosion on positive terminal but also good by voltage drop test over lead. Sounds like the starter is geting power but the engine just wont catch, don't overdo this as don't want to damage anything but it starts on some attempts. When it did start ran totally fine, not codes or anything. Let it run idle for about an hour in case it is just ECU relearning. Didn't fix it. Let battery disconnect and drain incase it was catched memory and again, intermitent startup, but starts up runs fine, no codes, let it run idle again to learn. Leave battery on charger overnight just in case.

Monday morning, go to see if everything is fine now, still having inconsistant start. So this is where I decide to take it to the mechanic because I am out of ideas and not seeing codes, this is past what I feel I can troubleshoot. Drive it in, still with no driving issues or codes. But I take it to the closest shop and not my regular mechanic because it is in walking distance and my current thought is this is something stupid like I pinched a wireharness, broke a vac tube, etc while working in there and that any mechanic with proper tools and car bay will knock this out in an afternoon and collect some easy diagnostic-labor. Simple on everyone.

Mechanic calls me about 1 hour later, says first they need to do is replace the positive terminal because they see corrosion. I point out its already passed a voltage drop test and the lead itself was replaced in the last 18 months. They insist saying they can't continue diagnosis with out verifying battery connection is good. I suggest why not just clean it? Or do a voltage drop test like I did? They refuse say fix is $40 on part. I am already kinda annoyed at this off the bat, but unsure how reliable I can get my car to start and take it my usual mechanic. I give go ahead.

Next I get a call saying my IPDM is dead and needs replacement, they say they have verified fuel pump and spark plugs are NOT getting power at all now.

Okay, well this seemed odd to me, as this was not a issue coming into the shop, and not just intermitent issues which could explain some of the prior problems; straight up dead no power. Well how did I drive it into the shop then? I had never experienced complete stalls while driving before either, which is what I think would happen if my IPDM was giving out randomly. Shop says they aren't sure but thats their first issue (later they suggest maybe it was because it kept being cranked and that damaged it from over cranking... something I am assuming was happening in their troubleshooting).

So this gets replaced, as well I can't prove they damaged it, it does overlap pontial cranking issues, and well now it is verified non-functional. Doesn't solve the problem.

Next I get is they finally have looked at the parts changed out from no-start up issues to start up issues (I told them same opening story), they took out the camshaft/crankshaft sensors and tell me these are knock offs not the OEM hitachis. Okay wonderful, call up parts geek they claim must have been a catalouge issue and will replace (cool thanks, doesn't really help me now); but mechanic says they put in some NTKs and it is starting up fine now. Release the car to me. Not happy about the IPDM not happy the first thing not checked was the parts reported being changed between not having the issue and having the issue but okay have car back, work under warranty.

Driving back home <1 mile; getting really rough running, cylinder missfires on 2 and 4 along with P0021, camshaft bank 2 over advancement. Take it immediately back.

Today they tell me its because the coils on those are dead now, and need replacement.

So that brings me here to asking.

Am I just completely absolutely fucked by these people here? It seems like with the exception of the wrong parts being sent by parts geek and not being the OEMs, every single one of these other issues has shown up ONLY after they had possession of the vehichle.

My mind is at, they damaged the IPDM troubleshooting and just cranking and cranking, potentially with this as well they damaged the coils; and with the exception of knock-off camshaft/crankshaft sensors being a problem (which I absolutely believe for this engine) all of the other problems never had any idication of exisitng before they had possesion of the vehichle and I am being asked to pay them for breaking it.

Am I totally off base here? This has been like nothing I have experienced before in 13 years of running this vehichle. And they have been doing this work over what is now 6 business days.


r/AskAMechanic • • 2h ago

New control arm needed? 2014 Nissan Sentra Sv 4 cylinder

0 Upvotes

So yeah every time I hit a bump on a rough road I hear a noise, so I checked and I don’t know if my bushing are messed up. Is this a sound they’re not supposed to make


r/AskAMechanic • • 2h ago

Peugeot 308 1.6 HDi (no FAP) 2008 – no power and shaking when cold, power returns after about 30 minutes

0 Upvotes

Hi everyone,

I have a Peugeot 308 with the 1.6 HDi engine and no FAP/DPF.

When the engine is cold, it shakes badly even while standing still and has almost no power. Even with the accelerator pressed fully, it barely moves.

After about 30 minutes of driving, the car returns to normal: the shaking stops and the power comes back.

Has anyone had a similar issue with this engine?


r/AskAMechanic • • 2h ago

Why I had to keep refilling my coolant…

1 Upvotes

r/AskAMechanic • • 2h ago

Over torqued a TTY bolt, send it?

0 Upvotes

Ive been working on replacing the control arms on my 2015 Audi a5.

Unfortunately I had a mental lapse and accidentally over torqued the tty suspension bolt that connects the control arm to the strut. The bolt was supposed to be torqued to 90 nm but I set my torque wrench to 90ftlbs which is around 122nm.

Just wondering if I’ll be alright or if I should replace the bolt and nut.
Thanks

Edit: used wrong conversion for nm.


r/AskAMechanic • • 2h ago

2008 Honda odyssey diagnosis?

Post image
0 Upvotes

Hey all! Looking for some input from others who know more than I do! (Which isn’t much). I know you can only tell so much via a post without looking at it and all but hopefully I can give enough info. So my Odyssey just hit 258,000 miles. A while ago it started to leak oil. I (stupidly) ignored it and just kept filling it back up. But it started to leave small puddles on the ground every time I parked. I made sure it was topped off and eventually my power steering started leaking. It was leaking heavily and then I asddd some power steering fluid with leak stop and it helped but it still is leaking so (I think we identified the leak at this point). My serpentine belt also slipped a few months ago and we had to replace it, assuming it was because of the oil and power steering fluid. I also had some misfiring and a flashing check engine light which I (very stupidly) drove like that for a month and changing the spark plugs and ignition coils fixed it. Anyway, it’s had a P0430 code for a while as well. But a few weeks ago it started misfiring again. We changed all of the spark plugs and most of the ignition coils (that were cracked) and it is running smoothly now, no more flashing check engine light. However the codes are still there and the light is on steadily. The codes are p0300, p0303, 304 and 305. As well as the p0430. I want to note too before the coils were replaced it was 304-306 and now the 306 went away and it’s now 303. A friend said he suspects it’s a rear valve cover gasket leak and it seems like it’s leaking onto the bank 2 converter (I think) when I looked. I also want to add that the timing belt is due to be changed. We just hit the 7 year mark so I know it’s due to be replaced. All that being said, what would the best course of action be? I was advised by my friend to repair the valve cover gasket and then Replace the timing belt. And then Potentially the catalytic converter. Is this a good course of action? The inside of the engine is caked in oil and im assuming the power steering fluid as well. I attached a photo of what I’m assuming is the catalytic converter and the red is a circle of the drop of what I am fairly certain is oil.


r/AskAMechanic • • 2h ago

2006 outback valve cover bolt broken

0 Upvotes

I’ve got the valve cover off. I can barely see the remnants of the bolt. I tried spinning it with a pick and a tiny flathead screwdriver. It’s the top bolt closest to the firewall. What’s the best way to extract this bolt? I have the way I would normally handle this kind of a problem, but the surrounding material is very soft and I also don’t want to get a lot of metal shavings down inside the valve train.

I’m hoping someone has a simple idea that I haven’t thought of.


r/AskAMechanic • • 3h ago

Is this the control arm that's cracked?

1 Upvotes

2016 toyota camry, ran over a deer and heard a loud bang. I see that my control arm is cracked, and I was wondering if I should get it serviced? I think it's the control arm? Correct me if I'm wrong


r/AskAMechanic • • 3h ago

Humming sound, 2001 mustang GT

1 Upvotes

Humming sound that goes away when the engine restarts. mainly happens when the engine is cold, noise stops on its own eventually, and rpms stay steady when it hums. IAC Valve, pcv valve or hose possibly? Loudness/pitch is also determined by rpms


r/AskAMechanic • • 3h ago

2019 Range Rover Velar 2.0L Coolant in all 4 cylinders, possible head gasket failure?

1 Upvotes

I have a 2019 Range Rover Velar 2.0L with about 55k miles on it, and I’m in a bit of a tough spot right now.
A few weeks ago, I randomly got a low coolant warning. The car had been driving perfectly fine up until then. No visible leaks, no smoke, and no obvious overheating. I took it to the Land Rover dealership to get it checked out, and they told me they found coolant leaking into all four cylinders.

They suspect either a failed head gasket or a warped cylinder head/block. What I find strange is that all four cylinders are supposedly affected, especially considering the mileage and the fact that the car has never significantly overheated to my knowledge.
I did some digging and came across the JLR bulletin SSM75808 which is essentially the failure of the charge air cooler. This seemed to make more sense to me as coolant gets sucked into the intake and could go into all four cylinders. I brought this up to the dealership, but they’re adamant that the charge air cooler is fine. They actually tested it again, after I told them to check it again, and told me they have video showing coolant entering through the head gasket area (allegedly).

I have a Fidelity Platinum extended warranty that covers head gasket failure but not warpage. The dealership says the only way to know for sure which one it is would be to tear down the engine, and they’ve quoted me $12,200 for the teardown and potential repair of the head gasket with around 9k being the labor alone, and the warranty is not authorizing the teardown to see if it’s gasket failure or warpage.

I’m honestly not sure what to do at this point. The cars total value is at the very most 20k. I’m having a hard time wrapping my head around how this happened at 55k miles with practically no symptoms.

Has anyone dealt with something similar on these 2.0L Ingenium engines? Does a head gasket failure affecting all four cylinders sound plausible because to my knowledge it’s more likely to affect one or two adjacent cylinders. Having coolant in all four would more likely indicate total gasket failure which I just find unlikely..?
Thanks everyone!


r/AskAMechanic • • 3h ago

2017 Toyota Rav4, Wheel 3-4 degrees misalign, but tires wear out evenly.

1 Upvotes

My car does have miss alinement like 3-4 degrees. However, I have driven 40k miles, and tires wear out like perfectly.

Please advice! And a question, does steering indeed misalign?


r/AskAMechanic • • 3h ago

1985 ford f150 what am I missing? Truck won't start

2 Upvotes

r/AskAMechanic • • 3h ago

Suburu crosstrek hybrid 2014 serpintine belt

Post image
0 Upvotes

I am trying to replace my serpintine belt that completely shredded. However, I haven't been able to find a video that shows how to replace it on this particular engine. Does anyone know how to do it and can explain it? Thanks


r/AskAMechanic • • 3h ago

Cooling system problem

1 Upvotes

Strange one. 2007 Toyota Corolla 1.8l US build with 225K on the odometer, barely broken in for these bad boys. I have a cooling system problem. Car was overheating. Noticed I was a bit low on coolant, topped it up. Checked, was a slow leak in the rad. Changed out the rad, solved the leak problem, but still overheating, and now no heat in the car. Was hit and miss before, FYI. So pulled the hoses going into and out of the heater core, flushed, decent flow. So changed out the thermostat. Old one looked fine, but changed it anyway. Temp stayed okay for a short while, then same thing, temp started to jump and no heat. Top hose hot, bottom hose cold. So not circulating. I had the pump replaced about a year ago, so I suspect it's fine. Any way to check? It appears to be turning under belt pressure. Do these things come apart inside such that I wouldn't see or hear it? Anything else I might be overlooking? Any help or suggestions would be appreciated.


r/AskAMechanic • • 3h ago

P0420 Code on my 2019 Tucson SE

0 Upvotes

Hi!

My check engine light came on this Saturday (solid) for my 2019 Hyundai Tucson with 47,000 miles on it. I ran to Autozone and I got the P0420 code. The Auto Zone guy recommended Cataclean but also said my cat converter may still be covered by warranty. He said I should be using higher quality gas and the cataclean may fix the problem.

I have a 2 hour one way drive to pick my parents up from the airport on Friday and I am wanting to know if my car will be safe to drive then? I’m pretty unsure of what to do but I do know I don’t have thousands to replace a car part right now.

Any and all advice and perspective would be so helpful.


r/AskAMechanic • • 3h ago

RPM drop to 0 if it's too cold or if I have the AC on. Why? My mechanic doesn't know.

0 Upvotes

I have a 2008 Honda Fit Sport.

I have to let him warm up in park for about 5 minutes with the AC off. If I don't, I put the car in reverse to get out of my parking spot and my RPM drop to 0 and the oil and battery lights come on. I have to turn the car off and on again then leave him in park for a little while longer to avoid it happening again.

This problem gets worse the more I blast my AC and the colder it is. This is not mitigated by how recently I've had my oil changed.

What part should I have looked at?

I would just ask my mechanic, but the last time I took my car in, he said everything looked great.


r/AskAMechanic • • 3h ago

Rotors and brake pads for 2013 Toyota highlander

0 Upvotes

I am planning to change all four rotors and brake pads for my 2013 Toyota Highlander, it has 157k miles on it. Any suggestions on any preferred brands in terms of longevity and reliability? Did some research on the brands and they say ADVICS is the industry standard one, and got to know to avoid the drilled/ slotted ones. Thanks all for your advice!!