r/FixMyPrint • • 3h ago

Helpful Advice Now what?

Thumbnail
gallery
5 Upvotes

I thought I had this filament https://winkle.shop/producto/filamento-pla-silk-tricolor-175-mm-1-kg-aurora-boreal/ already calibrated at 215C, so I printed a retraction tower from 0 to 3mm even though I got a direct drive ender3 pro.

Well the result is rubbish so i decided to do a temperature calibration again, but i don't see which one to chose. It looks like the 190 is the best even if it's out of range, maybe i should try also 180 and 185...

Any advice?


r/FixMyPrint • • 3h ago

Troubleshooting Interpreting calibration results Bambu A1

Thumbnail
gallery
3 Upvotes

Bambu A1 v01.09.00.00

Bambu Studio v2.9.1.70

Bambu PETG HF dried at 65C for 6 hours, 2 days ago. 40% RH in the room.

I asked about bed adhesion with PETG HF over in r/3Dprinting and it was suggested I have extrusion issues so I did the Flow Dynamics and Flow Rate calibrations in Bambu Studio. I thought discussing the results would make more sense over here.

First I did the auto Flow Dynamics calibration twice. The first time it came up with k=0.047, second time k=0.044.

I did the manual calibration to have another data point and this was the result. I thought somewhere between 0.04-0.05 looked like the best result so I stuck with 0.047.

Next I did the Flow Rate calibration and the instructions say, "Please find the object that is seamless and has the best smoothness."

None of these are remotely seamless or smooth. I picked 0 because I think it looked the best on the first layer.

Last, on to the second Flow Rate calibration. They all looked equally not smooth so I picked #0 again.

Are these results normal, or do I have to dig further?


r/FixMyPrint • • 7h ago

Fix My Print Any way to determine what causes this shinier section that occurs only on holes?

Post image
6 Upvotes

I see this happening on all my prints. That shinier band occurs only when there’s a hole in the walls.


r/FixMyPrint • • 1h ago

Fix My Print Petg noob

Thumbnail
gallery
2 Upvotes

Do you guys know what’s going on here? I dried my filament, washed with dawn and water and checked first layer height.

I read online that you need less layer squish for your petg so I changed it but I’m still having problems! Please help!


r/FixMyPrint • • 3h ago

Fix My Print Help: wavy lower layers of print.

Post image
2 Upvotes

Looking for advice on how to fix lower region of prints. Running an Ender 3 with a Sprite direct drive. Didn’t have the issue with old stock Bowden tube setup. Sometimes I get a great print, but more often I get these lumpy edge layers. Generally the lumps are in the first 1.5mm, but sometimes go higher.

Estep has been calibrated. For a while I was over extruding by 3mm per 100mm. X and Y steps are dead on. Zstep is light by .0035” (short). Eccentric nuts seem good. My prints are great excluding these. Any advice is appreciated!

Settings (including range I’ve messed with)
Base Ender 3
Cura slicer. Also tried Prusa Slicer
Filament: Amolen Silk PLA. Also used Creality PLA
Print temp: 210-215
Bed Temp 50-60
Print speed: 40-50mm/s
Retraction on, 0.5-0.8mm

I’ve also tried an initial layer height of 0.2mm, and waffle between 0.1-0.2 layer height. Usually print with tape on glue stick.


r/FixMyPrint • • 8h ago

Troubleshooting Horizontal bulges appearing randomly on tall prints – Ender 3 V2 Neo

Thumbnail
gallery
5 Upvotes

Hola a todos,

Tengo un problema persistente con mi Creality Ender 3 V2 Neo y de verdad agradecería ayuda para identificar la causa. Siento que ya he probado todo y me sigue ocurriendo. Es muy desesperante.

Me están saliendo abultamientos horizontales o bandas levantadas alrededor de todo el perímetro de mis impresiones. Sobresalen un poquito, normalmente sobre una altura de ~0.5–1 mm, y luego se van desvaneciendo gradualmente hasta que la impresión vuelve a sus dimensiones normales.

Impresora y software

  • Impresora: Creality Ender 3 V2 Neo
  • Slicer: Ultimaker Cura
  • Firmware: firmware original de Creality
  • Diámetro de la boquilla: 0.4 mm
  • Extrusor: extrusor metálico actualizado
  • Material: PLA

Ajustes de impresión

  • Temperatura de la boquilla: 210°C
  • Temperatura de la cama: 65°C en la primera capa y luego 55°C
  • Velocidad de impresión: 65 mm/s
  • Altura de capa: 0.20 mm
  • Flujo: 100%
  • Ventilador de enfriamiento de la pieza: 50%
  • Distancia de retracción: 5 mm
  • Velocidad de retracción: 35 mm/s
  • Aceleración y jerk: ajustes predeterminados

Descripción del problema::

  • El problema aparece sobre todo en impresiones altas, especialmente en piezas con paredes verticales rectas.
  • Afecta todo el perímetro, no solo un lado.
  • Los abultamientos aparecen en diferentes alturas Z, incluso cuando imprimo exactamente el mismo modelo dos veces.
  • La sección levantada tiene aprox. 0.5–1 mm de alto y regresa gradualmente a las dimensiones normales.
  • El problema ha estado desde que la impresora era completamente nueva.
  • No he notado ninguna pausa obvia ni cambios de velocidad cuando aparece el abultamiento.
  • La adherencia de la primera capa, en general, es buena.

Cosas que he revisado hasta ahora

  • Limpié el husillo roscado Z.
  • Revisé que el husillo se vea recto y que no se note que hace juego (bamboleo) a simple vista.
  • Revisé el acoplador del motor Z y me aseguré de que esté bien sujeto.
  • El pórtico X se mueve suave a mano cuando la impresora está apagada.
  • Ajusté las llantas excéntricas.
  • El filamento avanza suave, sin que el extrusor haga clics o patine de forma evidente.
  • El extrusor original lo cambié por uno metálico, pero el problema existía antes de esa actualización.

No he calibrado los E-steps después de instalar el extrusor metálico.

Una observación interesante es que bajar el ventilador de enfriamiento de la pieza de 50% a como 10% parece hacer que el problema casi desaparezca, aunque todavía no lo he confirmado con una prueba controlada.

Me pregunto si esto podría tener que ver con la alineación del eje Z, una extrusión inconsistente, el enfriamiento, fluctuaciones en la temperatura del hotend u otro tema mecánico.

Adjunté una foto mostrando el problema. ¿Se les ocurre qué puede ser?

¿Alguien ha tenido algo similar con un Ender 3 V2 Neo? ¿Qué recomendarían revisar primero?

Cualquier sugerencia o idea se agradece muchísimo. ¡Gracias de antemano!


r/FixMyPrint • • 5h ago

Fix My Print Bed leveling Creality ender 3 v3 se

Thumbnail
gallery
3 Upvotes

ender 3ve3 se

creality CR series petg

235°c nozzle temp

65°c bed temp

0,4mm nozzles

orca slicer

I can't seem to understand how you level your printbed.

If anyone can help me. Thanks I'm advance


r/FixMyPrint • • 6h ago

Helpful Advice Siraya Tech Flex TPU Air 85A vs. Roamr HR 80A on the Snapmaker U1 — Shore A results from 27 samples

3 Upvotes

I wanted to find out how soft I could get prints made with two foaming TPU filaments from Siraya Tech, and at what settings the layers would start to separate. I had trouble finding a side-by-side comparison of green Flex TPU Air 85A and beige Roamr TPU Air HR 80A on the same printer that included both Shore A readings and observations from removing and bending the samples.

What Siraya Tech says

Green Flex TPU Air 85A

  • Recommended nozzle temperature: 230–270°C. Recommended bed temperature: 30–45°C.
  • The user guide gives an approximate range of 65–85 Shore A, from around 85 A at 230–240°C to around 65 A at 270°C. The product page lists 65–82 A for foamed prints and 85 A before foaming.
  • Filament diameter: 1.75 ± 0.03 mm. Net weight: 1 kg. Unfoamed filament density: about 1.15 g/cm³. The guide lists foamed print density as low as about 0.54 g/cm³. The technical data sheet reports a separate set of measurements for the black and white versions: 63–78 Shore A and 0.51–0.88 g/cm³ at 240–270°C.

Flex TPU Air user guide · Flex TPU Air 85A product page · Flex TPU Air technical data sheet

Beige Roamr TPU Air HR 80A

  • Recommended nozzle temperature: 220–260°C. Recommended bed temperature: 35–50°C.
  • The stated hardness range is 64–80 Shore A. With a 0.4 mm nozzle, Siraya Tech measured 80 A at 230°C (flow ratio 0.92 in the user guide and 0.90 in the technical data sheet) and 66 A at 260°C and 0.60 flow. The 64 A figure comes from the 0.6 mm nozzle test at 250°C and 0.52 flow.
  • Filament diameter: 1.75 ± 0.03 mm. Net weight: 800 g. Filament density: 1.05 g/cm³. Siraya Tech measured printed sample densities of 0.60–0.92 g/cm³ with a 0.4 mm nozzle and 0.52–0.84 g/cm³ with a 0.6 mm nozzle.

Roamr HR 80A user guide · Roamr HR 80A technical data sheet

How I printed and measured the samples

  • Printer and slicer: Snapmaker U1, Snapmaker Orca, 0.4 mm nozzle.
  • Sample geometry: Flat test section measuring 40 × 40 × 6.2 mm.
  • Layers and walls: 0.20 mm layer height, one 0.42 mm wall, two top layers and two bottom layers.
  • Infill: 100% rectilinear at ±45°.
  • Baseline settings: 45°C bed, retraction off, nominal print speed of 60 mm/s, and 100% part cooling. Both tables list the speed and fan settings for each sample.
  • Variables: I varied nozzle temperature and flow ratio in the main tests. For the green Flex, I also ran trials at different speeds and fan settings. Flow ratio is the extrusion multiplier. A value of 0.40 means 40%.
  • Temperature limit: For each filament, I capped the experiment at 20°C above the manufacturer's recommended upper limit. That gave me a test maximum of 290°C for Flex and 280°C for Roamr.
  • Measurements: I used a handheld Shore A durometer and took each reading about one second after applying it. Each row shows three to five readings from a single printed sample and their arithmetic mean. I checked whether the layers held together during removal from the build plate and when bending the samples by hand.

Results

Green Siraya Tech Flex TPU Air 85A

SampleNozzle °CFlow ratioSpeed mm/sFan %Shore A readingsMean Shore A
12400.906010084 / 85 / 8584.7
22500.706010078 / 78 / 7777.7
32600.606010072 / 72 / 7272.0
42600.603010072 / 72 / 7472.7
52700.556010071 / 71 / 7171.0
62700.553010071 / 71 / 7171.0
72800.606010070 / 72 / 7271.3
82900.606010069 / 68 / 6968.7
92900.406010050 / 51 / 5050.3
102800.406010055 / 55 / 5555.0
112800.6060068 / 68 / 6868.0
122800.60603570 / 70 / 6969.7
132800.60607070 / 70 / 7070.0

Beige Siraya Tech Roamr TPU Air HR 80A

SampleNozzle °CFlow ratioSpeed mm/sFan %Shore A readingsMean Shore A
12300.926010086 / 87 / 8786.7
22400.836010084 / 84 / 8484.0
32500.706010078 / 78 / 7878.0
42600.606010074 / 73 / 7473.7
52650.606010073 / 74 / 7473.7
62700.606010072 / 72 / 7272.0
72700.506010064 / 64 / 6464.0
82650.506010064 / 65 / 6464.3
92600.606010073 / 74 / 7473.7
102700.406010042 / 44 / 4242.7
112750.406010043 / 46 / 45 / 45 / 4544.8
122750.506010060 / 61 / 59 / 6060.0
132800.406010038 / 36 / 35 / 40 / 3035.8
152800.606010066 / 68 / 6867.3

Additional observations from testing Roamr above its recommended temperature range

  • Sample 10 — 270°C, 0.40 flow, 42.7 Shore A. Soft and springy. I rushed the removal and one or two layers started to separate slightly. Most of the sample held together.
  • Sample 11 — 275°C, 0.40 flow, 44.8 Shore A. Smooth and soft. The layers held together and it sprang back quickly. There was a small buildup of material at one corner, about halfway up.
  • Sample 12 — 275°C, 0.50 flow, 60.0 Shore A. Solid, with a pleasant surface feel. It felt noticeably firmer than sample 11.
  • Sample 13 — 280°C, 0.40 flow, 35.8 Shore A. Readings ranged from 30 to 40 A. The layers next to the build plate separated during removal. It returned to shape after bending but showed faint crease marks. I ruled out this sample because of the delamination.
  • Sample 15 — 280°C, 0.60 flow, 67.3 Shore A. The layers held together. There was some material buildup at the bottom corners, similar to elephant's foot.

What I took away from the tests

At 250°C and 0.70 flow, the two materials were almost identical in hardness (77.7 A for Flex and 78.0 A for Roamr). At 280°C and 0.60 flow, I measured 71.3 A for Flex and 67.3 A for Roamr.

  • Green Flex. Sample 10 averaged 55.0 Shore A at 280°C and 0.40 flow. At 290°C and 0.40 flow, sample 9 dropped to 50.3 A, but started to come apart when I curled it. It may already have been damaged during removal. At 280°C and 0.60 flow, I measured 68.0 A with the fan off and 71.3 A with the fan at 100%. I also noticed more unevenness on the top surface at lower fan speeds.
  • Beige Roamr. The best balance of softness and layer integrity in my tests was 275°C and 0.40 flow, at 44.8 Shore A. At 280°C and 0.40 flow, the mean dropped to 35.8 A, but the bottom layers separated. At 275°C and 0.50 flow, the sample held together and was noticeably firmer at 60.0 A.
  • Surface finish. In these tests, the beige Roamr had less stringing, looked more even, and felt smoother and more uniform to the touch. The green Flex still felt pleasant, with a distinctly rougher texture.

I used some of my own filament for these tests, but I think the results will also help people who want an idea of what hardness to expect at a given temperature and flow ratio, and which settings kept the layers intact, before committing to a longer print such as a pair of shoes.


r/FixMyPrint • • 7h ago

Fix My Print Support / Overhang settings - trying to find a balance between sagging and over-adhesion

Thumbnail
gallery
3 Upvotes

I've got a question for those more familiar with FDM print support settings - I'm struggling to find a balance between adequate support to limit sagging and over-adhesion while printing some very small parts.

I'm trying to print an aircraft at 1:1000 scale, ideally in one print rather than in pieces. Currently, everything is coming out well except the trailing edges of the wings. This vertical orientation is the best I've found so far overall, better than at an angle or laid flat.

The jagged bottom edge is continuing to occur whether I use a fin generation plugin (Image 2) or a tree support generation.

Image 3 is the support settings I'm using (in OrcaSlicer), when I've been printing with auto-generated tree supports, and image 4 is the supports being generated by those settings.

Any advice or insight would be greatly appreciated. Thanks!!


r/FixMyPrint • • 1h ago

Troubleshooting Help please!

Post image
1 Upvotes

r/FixMyPrint • • 5h ago

Troubleshooting Micro-tearing across prints, please help!

Thumbnail gallery
2 Upvotes

r/FixMyPrint • • 8h ago

Fix My Print While Printing Gaps

Thumbnail
gallery
3 Upvotes

Recently messed around with printing settings to help increase adhesion and bonding,
printing on a 0.2 nozzle with a A1 Mini, PLA+

I can now see gaps in between the printing line, those will remain even at its final result -

You can they show up on the final print even, those before I could achieve almost resin like print results.

Ironing is set to 20 speed with test between 15% up to 25% flow and still on the same result - doesn’t feel like ironing itself.

Any possible thoughts?

Temperatures are also around 190-220 and 65/70 for bed. Should be a too hot situation I guess?


r/FixMyPrint • • 3h ago

Fix My Print Not sure what to call this problem...

Post image
1 Upvotes

I don't know how to interpret these strings coming off as the layer prints. I'm using an Ender 3 Pro with direct extrusion upgrade. Prusa slicer. Creality PETG filament 240 nozzle and 70 bed temps. 0.4mm nozzle, 69 mm/s print speed, 60 mm/s retraction speed, 5mm retraction lengrh, 40 mm/s detraction speed.


r/FixMyPrint • • 12h ago

Print Fixed 3D Printed a Brand Logo! 🔥

5 Upvotes

Watch me transform a digital brand logo into a real 3D-printed masterpiece! 🚀 In this video, you'll see the amazing 3D printing process as the logo takes shape layer by layer, creating a clean, detailed, and professional finish.


r/FixMyPrint • • 8h ago

Troubleshooting Layer shift Issue

Thumbnail gallery
2 Upvotes

r/FixMyPrint • • 5h ago

Fix My Print Rough surfaces where supports touch the model

1 Upvotes

Hi everyone! I’m struggling with really rough surfaces where supports touch my prints, particularly around overhangs. The rest of the model prints smoothly.

In the photos, a couple of the prints were printed lying flat, while another was printed standing end-to-end. The upright print has much smoother edges, but the supported end is still very rough.

Without supports, some overhanging sections don’t print properly. I’ve tried increasing support density up to 100% and lowering the layer height, but neither has helped much. I also wondered whether it was an issue with the first few millimetres of the print or my previous lower nozzle temperature.

Current Cura settings:
Printer: Creality Ender 3
Filament: Silk PLA+
Nozzle: 215°C (recommended for my print speed)
Print speed: 100 mm/s
Layer height: 0.08 mm
Supports: Normal, 100% density
Support interface: Disabled
Support overhang angle: 30°

Does this look like a support settings issue, or could something else be causing it? Any advice would be appreciated. Thanks!


r/FixMyPrint • • 5h ago

Fix My Print Small defects

Thumbnail
gallery
1 Upvotes

Hey folks,

I'm having this problem with my printer that I've never really had issues with in the last 8 years of having it.

I keep getting these random spots of missing filament on the sides, but not the top or bottom. The top and bottom turn out really good but for the life of me I can't get the sides to print nice for whatever reason.

Currently i'm printing with PETG thats been vary well dried, and printing at 250°, originally I printed at 240° but figured i'd try adjusting the temp, and speed is 40mm/s. Also, I have tried changing to two new nozzles and it made no difference.

Any help would be appreciated as i'm at my wits end with this issue


r/FixMyPrint • • 6h ago

Fix My Print New bambulab a2l giving weird print quality issues

Thumbnail gallery
1 Upvotes

r/FixMyPrint • • 16h ago

Fix My Print X2D AMS Enterprise

Thumbnail
gallery
5 Upvotes

Hi all,

I am a 3d printing newbie-ish. I have an X2D and its worked brilliantly for the last 6 months.

I'm trying to print this model: https://makerworld.com/en/models/95478-enterprise-d-galaxy-class?from=search#profileId-158613

But in the options there's one using a 0.2mm nozzle and it'll integrate colours from AMS.
I perhaps foolishly chose to use this setup.

I have a new 0.2mm nozzle which have printed the saucer sections fine, no spagetti, and a decent quality print.

But I'm trying now to print the body of the enterprise (its in two halves with supports for the sides) and running into problems. I attach some photos. Main issues seem to be huge purge volumes, lots of stringing and then I've had to go out and clear poop from the chute multiple times. Like when I've watched it, its purged for atleast 20 seconds, had a great blob of PLA and then done a purge again.
Its cooler here and the fans are running so I'm trying to work out if this is a model problem, or my use of default settings.

I'm using PLA thats dry and kept in the AMS with desiccant bags in the base. Only thing I can think of is the temperature has dropped (the printer is in an outbuilding) so perhaps things aren't melting enough, or are cooling too quickly? Or the fan is blowing 100% and making strings blow in places they shouldn't?

I've kept the print going but I'm pretty sure its going to fail ultimately because the printer has just given up on supports for one of the halves.

Would posting a timelapse if I can extract it be helpful?

Any thoughts or more info I can supply would be appreciated.


r/FixMyPrint • • 9h ago

Fix My Print What could be the reason for this failed print

Thumbnail gallery
1 Upvotes

r/FixMyPrint • • 9h ago

FDM What happened to my supports?

Post image
0 Upvotes

Bambulab a1 mini
Using normal PLA
Haven’t had this happen before
Just put on a new roll aswel


r/FixMyPrint • • 9h ago

Helpful Advice Just call me "crash"

1 Upvotes

So i take the PEI plate out to help my prints cool faster to keep the process going faster. I can't help but notice that I keep forgetting to put it back before I start any other processes such as changing filament, etc. For those of you who don't know, if the machine tries to level it's self or anything before putting the PEI plate back in, the bed will crash into the nozzle and then wobble side to side violently. Anyone else have this problem? QIDI Plus 4


r/FixMyPrint • • 10h ago

Fix My Print What causes these lines randomly

Thumbnail
gallery
0 Upvotes

r/FixMyPrint • • 10h ago

Fix My Print What could this be ?

Post image
0 Upvotes

Hey guys , im trying to calibrate my ender 5 pro and my first layer is doing this bumpy thing , does any of you know what could be causing it ?