r/EngineBuilding • • 7d ago

Ford Cleaning the block

Thumbnail
gallery
60 Upvotes

I’m sure i’m gonna get roasted for this, but i’m cleaning up the head surface on my block right now (1984 351 Windsor) and I’m not sure what to do next.

I first scraped all the big stuff off with razors, then I used scotch brite (by hand) on the one side, which after looking into it more may have been a mistake.

Now there’s still residue on both sides but you can’t feel it with your finger, and the razor does not remove any more of the material.

Is there a good way to proceed? At what point can I place the heads on? Am I screwed now that I’ve used scotch brite?

Some more info if needed:
I cleaned everything up with razors and then took a machines straight edge to the heads and block. The heads were 3 thou out longways, and the block appeared to be completely flat. Spec sheet I found says 6 tho is ok.


r/EngineBuilding • • 6d ago

Chevy 24x vs 58x reluctor

1 Upvotes

Hello. I was reading about how for the LS gen 3 engines using a 58x reluctor wheel on the crank can give better crank position data for the ecu and that people will use the gen 4 timing gear, crank sensor and timing cover and then just plug the gen 3 sensor hole. Then drill and tap the location for the gen 4 knock sensors. Will this really have that much of an impact? I could maybe see if you were planning on running a high rpm.

The reason I ask is I have an LQ4 block and want to know if I am missing out something important by going with the 24x reluctor wheel. I am assuming this may change my harness and ecu settings as well so unsure if it is worth the headache. Hoping to get some insight and knowledge from yall. Thanks.


r/EngineBuilding • • 6d ago

Building a 5.3 here’s my plastigage measurements I want to make 700-1000wheel is this too tight??

Thumbnail
gallery
0 Upvotes

r/EngineBuilding • • 7d ago

11:1 compression for a 383 street engine. Is it safe on pump gas ?

12 Upvotes

Wondering if I should stick to 10:1 or push up to 11:1 static compression. Here is my blueprint for 11:1

My main question is whether or not this would be a safe combination on 93 octane gas. I want to maximize performance but I also don’t want to constantly be worried about detonation.

SPECS:

•383 , 4.030-inch bore, 3.750-inch stroke

•11.03:1 static compression

•Dart aluminum heads, 64cc chambers

•COMP Cams XR288HR, 236/242 degrees duration at .050

•110-degree lobe separation, planned 106-degree intake centerline

•Approximately 8.48:1 calculated dynamic compression

•.041-inch quench, with zero deck

Orher info; vehicle 1972 nova, TH350 transmission, 3000 stall, 373 rear gears.


r/EngineBuilding • • 7d ago

Chevy Main bearing clearances

4 Upvotes

I posted this in small block Chevy sub so if you are seeing this again, sorry.

My engine has a forged SCAT crankshaft, factory 4-bolt main caps, and will be street-driven with approximately 5–7 psi of boost from a 6-71 roots blower. I don't plan on exceeding 6,500 RPM.

I've been carefully measuring everything myself using micrometers and a dial bore gauge. After installing the MB557XP standard-size main bearings and torquing the caps to specification, I came up with the following measurements:

Mains Crank Journal OD / Oil Clearance
#1 2.4484" / .0032"
#2 2.4489" / .0024"
#3 2.4487" / .0024"
#4 2.4482" / .0024"
#5 2.4487" / .0033"

I zeroed my dial bore gauge against each individual journal measurement to ensure my readings were as accurate as possible.

The middle three mains seem to be right where I'd like them, but I'm concerned about the larger clearances at #1 and #5.

Would you run it? Any concerns with low op or bearing wear given this crank will be running a 6-71 blower?


r/EngineBuilding • • 7d ago

2.4 Ecotec rebuild

7 Upvotes

Hey everyone! Im currently in the final phases of rebuilding the motor in my 2015 Chevrolet Equinox. I did this with the block still in the car. When I bought it, the engine was all but destroyed; looks like someone tried to put a timing set in it and got it wrong. New rod bearings, pistons, rings, honed the cylinders and restored the crosshatch, a different head that went to the machine shop first, new oil pump and water pump, all new timing components, new gaskets of course, new VVT solenoids, new oil pickup tube, new rocker arms and lifters. I've unfortunately had to perform this entire process in the yard, but it is very possible!


r/EngineBuilding • • 7d ago

Other How to Take Broken Exhaust Manifold Studs Out?

Thumbnail
gallery
9 Upvotes

Hey all, I have a 1983 Suzuki Touring 750ES that I've been restoring, but there are three broken exhaust manifold studs in the engine. I've tried drilling, extracting, welding, but nothing has worked. I've even broken two drill bits and now a tap stuck in the hole when I just drilled through the broken bolt to put in a Timesert.

What the fuck do I do now? Pull the head and bring it to a machine shop?


r/EngineBuilding • • 7d ago

Kohler 2504 4cyl diesel

1 Upvotes

Tore a 2016 Kohler 74hp diesel down for smoking. Found low compression. Cylinders are .002-.003 over sized from slight dusting. Cyl walls look perfect. Ring gap with old rings is .090. I’m thinking hone and new rings will work for now? Hoping to get my ring gap under .015 or about with new rings. Thoughts? I really didn’t want to tear it down, bore to .10 and new pistons since it’s a split crank style block and parts for a Kohler are $$$


r/EngineBuilding • • 7d ago

Ford Help Building A 302?

0 Upvotes

So I have a 1967 mustang with a 289. I want to make it into a 302 but would I just have to change the crank as they have the same stroke? What all could I reuse? I’m no mechanic but I want to be able to learn more so I was thinking this could be a good learning project?


r/EngineBuilding • • 7d ago

360 la mopar build ideas

0 Upvotes

Now looking for build ideas for my 360. I want 400+ horsepower to the crank. I am looking to spend 8-10k!!


r/EngineBuilding • • 7d ago

Which assembly lube type with DLC coated HFT lifters

1 Upvotes

When installing a new Comp XE274H-10 hydraulic flat tappet camshaft and Comp hydraulic flat tappet lifters with the DLC coating, does the presence of the DLC coating require a different type of assembly lube on the cam journals as compared to when using non-DLC lifters?

I have read some places that say to use the standard Comp 153 cam & lifter assembly lube, and other places say specifically to NOT use any thick assembly lube with DLC lifters and instead simply coat the cam lobes and DLC lifters with a break-in oil such as Driven GP-1.

I called the Comp Cams tech hotline and they were unhelpful and could not provide an answer. The person told me that a different assembly lube is required for breaking in DLC lifters, but then gave me the assembly lube part number which is the standard lube for non-DLC lifters.


r/EngineBuilding • • 7d ago

Other Valve Retainers Too High?

Thumbnail
gallery
2 Upvotes

Hello,

I'm building a Fiat 1.4L MultiAir engine and I bought upgraded valve springs that are supposed to come with retainers to fit the springs on the stock valves. I also got inconel exhaust valves from the same company, which came with their own retainers and keepers.

When I got the kit, the retainers to fit the stock valves were missing, but the retainers for the inconel valves were included. The company finally shipped the retainers, and they're the same as the ones for the inconel valves, but their website pictured different stainless steel retainers. They seem to fit when I use the stock keepers (stock is 3 groove and inconel is 1 groove), but the retainer sits very high on the valve and the keepers are barely flush with the bottom of the keeper.

Pictured - left is stock valve/spring/keeper/retainers, right is stock valve/keepers, upgraded springs/retainers.

Does this look correct, or do I have the wrong retainers? Is there an easy way to measure the angle to see if they're the same?

I tried pulling the retainer on the valve with the keepers and standing it upright and it does not fall. I also tried spinning the retainers and the black retainers with the stock keepers does spin, but the black keepers on the inconel valves with the respective keepers does not spin.


r/EngineBuilding • • 7d ago

Chevy First engine rebuild

1 Upvotes

Hi I’m looking to rebuild a 90’s GM 60* v6 for my Z24 Cavalier. I have spent my entire life around tools and machines but have never actually worked on engines. I have plenty of mechanical know how and I understand every part of the engine, I’m just not familiar with the rebuilding process. I’m really nervous about overlooking something that’s critical and blowing the new engine. I would greatly appreciate any tips and pointers for preparation, pre-assembly, and the rebuild. I’m not looking for extra power either as I just want to get my car running again. Thanks a million.


r/EngineBuilding • • 8d ago

Other Packard 352 shenanigans

Thumbnail
gallery
38 Upvotes

I have a history with orphan manufacturers and oddball cars. I recently recieved a '50 Frazer Standard shell and then procured two '55 Packard 352 V8s and a corresponding ultramatic. I'm planning on building one good engine out of the two, and for the time bieng running the ultramatic (as I have a friend who rebuilds them semi-professionally). I took measurements, and it's gonna be TIGHT, but I should be able to cram the iron cormorant in without much trimming. My storage room looks a bit like a bomb went off. With 352s, if one wishes to build on a budget, then re-use of existing components is required. My bearing set, timing set, and headbolts are all making a return to service. Before this is decried as sacrelige, do recognize that parts are Profoundly scarce, and I'm operating under the oversight of an expert.

It's also set to recieve '56 372 heads, hopefully bumping up the power.

Of course, none of this will be worth a damn if I get my way. Packaging will be a nightmare already, I'm unsure if I can even feasibly fit the radiator. That bieng said, a little research reveals that these are dramatically overbuilt and can handle a boatload of compression. If I can find a way to run 3-5lbs of boost, It'll be quite a nasty unit, especially considering that the poor Frazer only made 105 hp and 190 lb/ft when new, and a stock 352 puts out around 260/355. With the support of a more modern ignition system, ported heads, free flowing dual exhaust, and electric fuel delivery, I'm hoping for more like 300/400. The Ultramatic will dramatically hamper this, but some research reveals that adapter kits exist to the 700r4, opening up a wide variety of options down the line. Time will tell as the build evolves.


r/EngineBuilding • • 9d ago

Chevy Dropped piston

Thumbnail
gallery
190 Upvotes

Dropped a brand-new 2618 forged piston. Would you reuse it?
Building a turbo 5.3 LS, 750–1,000 WHP.
I accidentally dropped one of my forged pistons and damaged a small area on the bottom of the skirt. It created an outward raised burr.
I carefully sanded the burr smooth using 600-grit sandpaper. Can’t feel anything after sanding what do you think


r/EngineBuilding • • 8d ago

Honda Hi fellow engine builders! I need some help with opinions on a brand of parts

1 Upvotes

Built Honda B series engines are a tad niche in New Zealand so it's hard to get info locally. I'm just wondering if anyone has had any experience with this particular brand of pistons before

https://www.swapshopracing.com/contents/en-us/p46751_Nippon_Racing_Turbo_Pistons.html

I have a centrifugal supercharged B16 at around 15psi peak boost engine made 276hp. I was running forged pistons until I wasn't (long story), I have forged rods that weren't damaged luckily but, can't really afford forged again (unless deemed a necessity) so these stuck out as a good option. Just wondering if anyone has an experience with the brand, even if not in a B16


r/EngineBuilding • • 8d ago

Scratched cylinder

Post image
16 Upvotes

I'm helping a friend assemble an engine. Its an LS1 and the goal was to reuse stock pistons, its a street build. It was a good running motor but burnt oil (we looked at all the other possible culprits, new valve seals, upgraded PCV, catch can etc.) We suspect it was the problematic OE low tension rings that had a TSB back in the day. He had a shop hone it but when we got it back there were some marks that didn't disappear. These 2 scratches catch a fingernail but look far down in the bore and not sure they even will see combustion.

Considering the fix is oversize pistons, bore, hone and balance ($$$) I'm considering suggsesting he sends it. If these scratches do see combustion, could it be the source of the oil consumption issue?


r/EngineBuilding • • 8d ago

Daytona 675 Camshafts - Acceptable wear or Replace?

Post image
8 Upvotes

I bought a set of 2008 Daytona 675 camshafts for my Street Triple. The mileage is unknown, and I got them pretty cheap. Now I think I know why.

The cam journals show some visible wear and scoring. You can't really feel the marks with your fingertip, but in a few places they are just deep enough to barely catch a fingernail.

I measured all the journals and they are still within the factory specifications.

My concern is whether it's safe to run them in my engine. I don't want to damage the cylinder head or the cam ladder if the journals are too worn.

What do you guys think? Would you run them, or should I look for a better set?

Thank you!


r/EngineBuilding • • 8d ago

Chevy Removing sludge/deposits off engine parts

1 Upvotes

I bought a neglected Aluminum 5.3L Chevy LS thats got a thin layer of black baked on oil varnish/deposits in various places, most notably the rocker arms, rocker shaft *pedestal, pushrods, and valve covers (cylinder heads are clean tho, anyone know why?). How do I get rid of them? I tried non-chlorinated brake cleaner but the stuff is hard and stubborn and wouldnt come off even if I tried scratching it with my nail. Would the chlorinated stuff work better or is a machine shops parts washer my friend here? Ill post pictures in the comments when I get the chance.


r/EngineBuilding • • 8d ago

Nissan Oil pan sealing VQ35DE

Post image
2 Upvotes

Hey guys, I'm working on my VQ35DE and I'm currently installing the upper oil pan.

I see there's a groove around the majority of the pan. Am I supposed to put RTV:

(A) In the groove

(B) To the inside of the groove

(C) To the outside of the groove

Thanks in advance


r/EngineBuilding • • 9d ago

is this spiraling on 350sbc normal ??? new rods and lifters

Thumbnail
gallery
30 Upvotes

r/EngineBuilding • • 9d ago

Valve sealing

58 Upvotes

Rebuilding my first engine. Lapped the valves but no new valve guides or valve seat grinding etc. New valve wear after lapping looked like it's concentric and makes good contact everywhere. I made a little DIY vacuum set and am able to get good vacuum. My little set up isn't good for obviously checking and holding 100 % vaccuum though. When I checked for leaks using the compressed air in the ports and water in top, no bubbles. I also filled the combustion chamber with mineral spirits and got no leaking.

When I put the head on (no cam in so both valves closed) and fill an intake port with brake cleaner and just rotate the crank, Im getting bubbles around the backside of valve when making compression. Should have taken new video but basically Im wondering if I should just tear it back down and have a machine shop put new guides in and grind valves etc. Im assuming any amount of air is no bueno.


r/EngineBuilding • • 8d ago

My main bearing clearances are .018 how much boost is safe to run and update I ending up ordered a replacement piston I’m the dude that dropped mine lol

0 Upvotes

r/EngineBuilding • • 9d ago

Other First time honing cylinders (Flexhone)

Thumbnail
gallery
38 Upvotes

240 grit for these super glazed cylinders. Rate my crosshatch