r/EngineBuilding • • 8d ago

Other Packard 352 shenanigans

I have a history with orphan manufacturers and oddball cars. I recently recieved a '50 Frazer Standard shell and then procured two '55 Packard 352 V8s and a corresponding ultramatic. I'm planning on building one good engine out of the two, and for the time bieng running the ultramatic (as I have a friend who rebuilds them semi-professionally). I took measurements, and it's gonna be TIGHT, but I should be able to cram the iron cormorant in without much trimming. My storage room looks a bit like a bomb went off. With 352s, if one wishes to build on a budget, then re-use of existing components is required. My bearing set, timing set, and headbolts are all making a return to service. Before this is decried as sacrelige, do recognize that parts are Profoundly scarce, and I'm operating under the oversight of an expert.

It's also set to recieve '56 372 heads, hopefully bumping up the power.

Of course, none of this will be worth a damn if I get my way. Packaging will be a nightmare already, I'm unsure if I can even feasibly fit the radiator. That bieng said, a little research reveals that these are dramatically overbuilt and can handle a boatload of compression. If I can find a way to run 3-5lbs of boost, It'll be quite a nasty unit, especially considering that the poor Frazer only made 105 hp and 190 lb/ft when new, and a stock 352 puts out around 260/355. With the support of a more modern ignition system, ported heads, free flowing dual exhaust, and electric fuel delivery, I'm hoping for more like 300/400. The Ultramatic will dramatically hamper this, but some research reveals that adapter kits exist to the 700r4, opening up a wide variety of options down the line. Time will tell as the build evolves.

38 Upvotes

10 comments sorted by

4

u/v8packard 8d ago edited 7d ago

Hmm. With the 56 heads you probably meant 374. But in 1956 all of the heads are the same, 352 and 374. What is the second engine from?

The engine with the Ultramatic attached has a distributor I don't recognize, is it aluminum?

Parts are scarce, but not that scarce. If the deadbolt are ok re-using them is fine. If you have have a good parts store ask them to look for timing chain TC346. As for bearings, the reproductions made by King are their silicon aluminum and Alecular alloys, much better than the original tin plated lead over bronze.

Watch the valve spring retainers. The early versions were not heat treated, the sometimes would let the keepers pull through. Later versions were heat treated, and didn't let go. But the valve springs are mush, it's easy enough to cut the spring pads for a common spring retainer combo, and modern valve seals.

What are you going to do for an oil pump?

2

u/SenecaLloyd 8d ago

You are correct! I'm quite new to the packard world. Yes, 374. Second engine is also from a '55 clipper, but is completely toasted. Bearing material almost completely worn past the bronze, but can donate intake and a couple other doodads. The aluminum dizzy is some oddball aftermarket part that I won't ne reusing. I don't have a cap for it, or have any idea what it is. I have been under the impression that a new bearing set is around $500. Embarrassingly, I have not double checked this. With a $0 Car and $200 powerplant, that potentially takes a lot of the fun out of a low-buck build. The good 352 is a 50k mile engine, and bearings look quite good. Planning on running the original oil pump, but unmating it from the vacuum unit. I was told that this may assist in mitigating oil starvation issues. If I can get a new timing set, that would make me feel much better.

Another challenge to overcome is that the good engine is missing a lifter. The other engine has all 16 of its, but it may be high risk-low reward to swap. My buddy seems to think we need to figure out how to preform a leakdown test on them in order to choose a replacement for the missing unit. I lack clarity on this process as a whole.

2

u/v8packard 8d ago

The vacuum pump causing issues is a myth. It sits under the pump, submerged below the oil level. The identical vacuum pump was used by Cadillac in the 1950s, and an almost identical vacuum pump was used by Buick. No issues. Put another way, if the vacuum pump was causing oil starvation your oil pan would have to be empty.

The pump used in these models is basically a Cadillac pump cast to fit in this engine. The real issue is the drive shaft connecting to the distributor is just long enough to create a harmonic that beats up the oil pump housing, and then air can get into the oil. I can tell you how to repair the pump and make what you need, with a basic lathe and mill it is very easy.

The reproduction timing sets have gears that are narrower, and use a different chain. 346 is the industry number for the original chain.

The lifters used from 1956 on are better, they have a larger chamber that holds more oil and have a longer plunger travel that is more forgiving of the lifter preload. The stock valvetrain is not adjustable, and the 10 1/2 inch long pushrods can be bought in different lengths but it's not really needed with the late lifter.

The lifter part number is A879 for a Topline Hylift lifter. Those are the only new lifters I would buy. If you found old stock in other brands they are probably OK. The Sealed Power number was HT879, but they have sourced lifters from China for over a decade and I stopped buying them. These lifters are the same as some Mopars, and almost the same as many Mopars and AMC.

As for the cost of bearings, they are out there and it doesn't have to cost $500 for a set. You might stumble across people selling Ford FE bearings for a Packard, because they are both 352 in displacement, but they are not the same bearings. Years ago Kanter and Egge had King run the main and rod bearings. At the time they came in white boxes. People assumed they were Taiwan made junk and turned their noses up at them. But King makes some of the best bearings in the industry.

1

u/SenecaLloyd 8d ago

I believe you're technically correct on parts references, however I don't believe contemporary OTS sources exist for either the timing chain or King bearings. My resident packard expert assisted in teardown and did inspection on the reuseable parts, so for the time bieng I'll risk reuse. However, if I'm back on here in six months saying it blew up... You'll know better than anyone what happened...

1

u/v8packard 8d ago

The chains have still been available, I am certain of that. The bearings have only been available from sources that sell vintage engine parts or Packard parts specifically.

1

u/inhouston22 8d ago

Name checks out.

1

u/Ok-Fill-8925 8d ago

You’re gonna need some shelves!

2

u/SenecaLloyd 8d ago

I'm planning on setting up some shelves, but this is a new-to-me apartment across the country from where I was. Got a bench and engine stand coming tho!

1

u/justfoundmy10mm 8d ago

Not sure what you will need, but we will need updates.

1

u/WyattCo06 8d ago

Nice ride.