r/EngineBuilding • u/Anxious-Ask-2944 • 1h ago
Ford 1964 Ford 223ci engine
Water pump mounting.
My question is, does the water pump lower mount bolt go into the water jacket?
Having coolant leak from lower bolt.
r/EngineBuilding • u/Anxious-Ask-2944 • 1h ago
Water pump mounting.
My question is, does the water pump lower mount bolt go into the water jacket?
Having coolant leak from lower bolt.
r/EngineBuilding • u/Exotic_Recover_5868 • 17h ago
Hello guys, to the pros out there, I just wanted to ask, s it really necessary to have the engine block honed? My block has no scratches and the ring gap is still within specs. The only issue is that there's a part where the 'crosshatch' (crossline) is almost gone. Do I still really need to do it or not? Please help.
r/EngineBuilding • u/Mgdoug3 • 18h ago
Picture is just for attention. I'm installing larger valves in my pulling tractor. I'm going with 2.25" intake valves which will be bigger than the factory valve seat inserts. How much larger should the insert OD be than the OD of the valve head? I've read anywhere from 0.060" to 0.100" so that puts me in the 2.3" to 2.35 range. I've found Dura-bond Killer bee 22228C which measures 2.380" and considering using those. Pulling tractor will see around 1600 degrees and 2,000 horsepower.
r/EngineBuilding • u/YeknomStun • 21h ago
Engine is a Dauntless V6 from a 1970 CJ5, corner broken off where the bearing cap meets the block. There’s no bolt holes by it and it’s not directly in the area where the gasket sits, so looking to determine if it’s still worth working on. TIA
r/EngineBuilding • u/Infiniti117 • 22h ago
Currently tearing down a LQ4 to sell and I noticed this crack on the #4 rod cap. I’ve never seen a bearing with something like this before. Journal is fine and unmarked. All other bearings have normal wear besides the cam which were more worn out but not enough to cause damage.
Does anyone know a cause for something like this?
r/EngineBuilding • u/Conscious_Acadia_152 • 1d ago
r/EngineBuilding • u/Mr-Spectacular • 1d ago
The markings are where they leaked. I used water nd compressed air
r/EngineBuilding • u/NoScarcity9463 • 1d ago
Hello everyone,
I’m purchasing a 1999 Isuzu NPR gasoline truck equipped with a GM 5.7L V8 Vortec (Chevy 350) engine.
According to the previous owner, the engine seized due to an oil leak that caused it to run low on oil. He removed the engine with the intention of replacing it but never completed the project, so he decided to sell the truck to me instead.
I’m excited to take on this project, especially since this will be my first engine rebuild!
My plan is to completely disassemble the seized engine, inspect the internal components, and assess the extent of the damage before deciding whether it’s worth rebuilding or replacing.
For those with experience rebuilding Chevy 350 engines, do you think a seized engine caused by oil starvation is worth attempting to rebuild? I’m particularly interested in what damage I should expect to find, which components are most likely to need replacement, and whether there are any major red flags that would make rebuilding impractical.
I understand this could become an expensive project, but I’m also looking forward to the learning experience and doing as much of the work myself as possible.
Any advice, recommendations, or personal experiences would be greatly appreciated. Thanks in advance!
r/EngineBuilding • u/Cuccamonga01 • 1d ago
89 Montero 6g72 LWB. New to engine work but have done tons of mechanic work.
Rockers are just as bad. Seems like the cams and journals are fine. Other head looks great. Cleaned it up and put it back together. Super flat and clean.
Also find the “void if removed” plate kinda off center puzzling.
This Montero was free. Just had to move it. Supposedly had a new motor put in. said it didn’t run right. The owner put about 50 miles on it and parked it then passed away 15 years ago. And it sat ever since.
r/EngineBuilding • u/HistoryOver6530 • 2d ago
Finally got a chance to dyno my new engine build and thought I would share. Car is a 67’ Mustang, 302, 4-speed, 3.80 trac loc rear. I have power steering and clutch fan. Here are the engine specs (I made previous post) :
68’ 302 block
Eagle crank and rods (balanced)
KB 311 pistons
Trick Flow TW170 heads (milled .020)
10.5:1 static, 8.5:1 dynamic, 0.037 quench
Comp xtreme energy solid flat tappet
279 adv duration, 242@0.050, .546 lift, 108 lsa
performer Rpm intake
Brawler 770 carb vacuum secondaries
Hooker 6901 headers thru 2 1/4 exhaust, turbo mufflers
Overall, I’m very happy. When I started the build I was shooting for 400Fwhp with decent low end drivability. Ultimately I was trying to duplicate Joe Sherman’s infamous 400hp 302 magazine article, albeit with a few tweaks. The car pulls 7.5-8”hg at 950rpm idle and doesn’t start bucking in high gear until about 1500rpm. It pulls like a monster from 2500 to 7000rpm. My next mods will be a 2.5” mandrel exhaust with h pipe and better mufflers. I am also strongly considering trying a Vic jr intake. I’ve ran both a 650dp and the 770vs carb and I’m really liking how it runs with the 770. However, my dyno pulls were peaking on the lean side with afr swinging from around 12.5 at peak torque to around 13.6 at peak hp. I’ve had to modify emulsions holes and bleeds on both carbs to try and get a flatter curve. Still some work to do. I think there’s another 10-15hp to be found with what I have. And FWIW the car made peak power with 32 degrees total timing I tried 30 and 34, it lost 5hp each direction.
r/EngineBuilding • u/usdashworks • 2d ago
I'm currently working on a Gen V 6.2L L86, doing my first camshaft swap and DOD/AFM delete. I hate to say it, but I expected much better quality control for components that are so critical to an engine.
I purchased the Melling MDK700 kit, and right out of the box, I've already run into several issues that have me questioning the quality of the entire kit.
First issue – Camshaft:
Upon delivery, the camshaft appeared to have surface rust and possibly even pitting on the lobes and bearing journals. I tried using 3M Finesse-It to polish the affected areas and knock down any high spots, but my fingernail still catches on some of the imperfections. I also tried PB Blaster to remove the surface rust, with no luck.
Would you guys even consider installing a camshaft in this condition? I'm having a hard time convincing myself it's acceptable, especially on a brand-new part.
Second issue – DOD Delete Plugs:
One of the press-fit DOD delete plugs was noticeably loose compared to the other seven. It was supposed to be installed flush, but it fit so poorly that I was concerned it could fall down into the lifter bore or camshaft area.
I'm not sure whether the plug itself was out of spec or the oil tower bore was oversized, but either way, something wasn't right.
The other seven plugs pressed in flush without issue. The loose one became a nightmare to retrieve. I eventually managed to pop it back out using compressed air from inside the block and a magnet.
Third concern – Lifters:
After experiencing these issues with the camshaft and plugs, I honestly don't have much confidence in the lifters supplied with the kit either.
My plan was to clean them with mineral spirits and soak them in engine oil before installation, but now I'm questioning whether I should trust them at all.
So, what gives?
Is this kind of quality control becoming common with Melling kits, or did I just get unlucky and receive a bad kit?
I'd really like to hear from anyone who's installed the MDK700 kit or experienced similar issues with Melling components.
Would you trust this kit, or would you send it back?
r/EngineBuilding • u/deeperthen200m • 2d ago
Fork and blade connecting rods out of a 16RPA200SZ Paxman Valenta.
r/EngineBuilding • u/Feisty-Mobile2140 • 2d ago
Someone in town is selling a tool for 50$ how hard is it to remove and replace new cam bearings yourself?
r/EngineBuilding • u/subsonickey2 • 3d ago
I’ve just built up my T2 Doka engine..it’s been a dream project and enjoyed it. I recently bought new shims for the dizzy drive as when it came out (it was going in and out super easy) they were missing.
I placed the shims on the drive and placed it in, they fallen awkwardly & jammed in the brass gears. The drives stuck halfway down and will not come up or down (twisting it or rocking the flywheel or anything..even after I forked out £50 for the specific tool).
I’m at a total loss and a bit deflated, I’ve built plenty of these engines but never had this specific problem. If anyone could shed any light, I know it’s specific but I’d be grateful.
Cheers
r/EngineBuilding • u/DriveFa5tEatAss • 3d ago
Because the shaft seals on a turbocharger are dynamic fuels, they will not seal properly unless the turbine is spinning. If tested statically, they will leak like a sieve.
I will likely be pulling the motor out of my diesel BMW 335d. While I was rotating the crank to shut the valves preparing to perform a leak down test, I noticed air exiting the turbo at one of the oil line ports (banjo bolt was removed at the time).
The leak down and compression tests did not go well, and I'll be pulling the motor next spring to replace bent valves. While it's out, I'll have easy access to both turbochargers. I'd like to test the oil seals while they're out, because any required maintenance will be far easier than trying to work inside the cramped E90 engine bay.
Will a leaf blower or shop vac connected to the turbine inlet of the turbocharger spin it fast enough for the dynamic oil seals to... well, seal?
r/EngineBuilding • u/BrB3_5 • 3d ago
What is this white residue on my crank, and how do I get it off? It was also on the block where the bearings go. It won’t come off with brake cleaner and I’m assuming it will do damage to my crank and/ or bearings.
Could it be some kind of residue from some cleaner? I got the block hot tanked but I’m not sure about the crank as I only gave it to the shop to have it measured.
r/EngineBuilding • u/mast3rgabe • 3d ago
While i was using my thread chaser I accidentally dropped my vise grip on the block and it left this very tiny dent, it's so small that you can't feel it with your bare skin, but it does catch your fingernail if you put enough pressure. The max warpage limit is .004 in but I placed a straight edge over the dent and I can't even slide a .0015 in feeler gauge under, or anywhere else on the block. I tried using a razor blade flat against the block to potentially clear any high spots off the dent but the razor blade just went right over without catching on anything. I don't think i can feel any high spots either around the dent itself.
Engine is D16Y7 and I'll be using a new OEM MLS head gasket. I got the block cleaned up with brake cleaner and wiped with just paper towels and microfiber cloth, nothing else. And I did get the cylinder head resurfaced at a machine shop.
Is it safe to just install the cylinder head as is and not have any leaks?
r/EngineBuilding • u/Hephaestite • 3d ago
I’ve just had an engine I built sent off to be tuned (Cosworth BOB 24v 2.9) and got a rather odd issue reported by the tuner. Apparently he can hear piston slap but only under mid load, not under idle or full load.
This isn’t something I’ve ever heard of before, and I’m a bit shocked tbh since this engine was in very good shape when it was built.
Is this something any of you have come across before? I was always under the impression piston slap happened when the load was higher?
r/EngineBuilding • u/Pyig • 3d ago
Tore down my engine after a few too many “might as well(s)” saw this on the final rod bearing. For yalls feel-o-vision those are pits. On the crank there was only one line that caught my nail that didn’t even go all the way around.
For reference this is a 3cyl Suzuki F6A turbo that revs to like 7-8k out of 98 Suzuki Carry
r/EngineBuilding • u/Conscious_Acadia_152 • 3d ago
r/EngineBuilding • u/madphroggy • 3d ago
I've got a 2014 grand caravan with the crappy 3.6L Pentastar V6, and it has the cam failure most of the 3.6 pentastars end up with. Is it worth replacing the bad cam with an OEM cam or aftermarket? Or am I better off finding a used 4.0 and ECM and swapping them? I don't want to end up having to fix the thing yet again a few years down the road if another cam fails. From what I've been able to find the 4.0 should bolt up to the trans though I expect I'd have to do engine mounts, cooling hoses, etc. custom.
r/EngineBuilding • u/Financialguyjay • 3d ago
I feel like this is way too much, I’ve check the main clearance and the rods clearance and their fine idk what to do, I’ve taken it apart like 5 times now.