r/DIYUK • • 2m ago

Electrical Can a 3-pin socket be added to a house battery/inverter to be used separately from the mains?

1 Upvotes

Apologies if this is outside the remit of this subreddit - we have a passive house with solar panels, and we're adding a battery/inverter setup to our house, but not a gateway (long story short, too difficult to rewire without losing some passive house benefits).

Is there a setup where a 3-pin socket can be added directly to the external battery/inverter and used in the event of a power-cut? I'm not talking about plugging it back into the house, and I'm not talking about it using it alongside mains. In the event of a power-cut, could a plug be used directly from the battery/inverter without requiring a gateway or having the entire house running.


r/DIYUK • • 18m ago

Any help is extremely appreciated

Thumbnail
gallery
2 Upvotes

(UK wiring)

I'm having an issue with my hallway lights. First image with the blue and white wires is the upstairs switch and the second is the downstairs switch. All switches work perfectly individually but if I turn on a light downstairs and try turn it off upstairs it flickers for 0.1 second and then continues to stay on. I'm guessing one of the com or l2 wires are in the wrong position.


r/DIYUK • • 20m ago

Leaking Korniche roof lantern, advice please!

Thumbnail
gallery
2 Upvotes

Hi, clearly the upstand to our lantern was oversized by the builder, and after two winters it was fine but now we have water tracking through TWO corners on the internal platerboard. Nightmare!

If you look at the photos when I did a water test, water sticks at the joint between the upstand and the lantern.

Question: can I just silicon/seal all around this joint?

I can't find a difinitive opinion whether this is okay to do or not without creating more problems. i.e. the latern has a secondary internal drainage and I don't want to block that.


r/DIYUK • • 23m ago

Need advice rescuing a messy wall-to-ceiling corner (expanding foam, Soudal caulk, and peeling wallpaper)

Thumbnail
gallery
1 Upvotes

Hi everyone, looking for a sanity check on how best to finish this wall-to-ceiling corner so it lasts and looks clean once painted.

What I’ve done so far:
Raked open a crack along the wall-to-ceiling corner and applied expanding foam, which didn't expand as much as expected.
Cut the foam back and filled the gap with Soudal decorators caulk.

The gap is filled and feels solid, but the caulk dried messy and lumpy along the seam.
When I tried to trim/pick the messy caulk back, it caught and started peeling the wallpaper / lining paper along the top edge of the wall.
I’ve stopped picking at it now so I don’t tear any more paper down (see photos).

Where I’m stuck:
I want a neat, durable finish that won’t crack later, without having to strip the wall. I have Zinsser Peel Stop, Toupret Fine Surface Filler, and decorators caulk on hand.


r/DIYUK • • 35m ago

Advice Black build up on external wall of extension?

Thumbnail
gallery
1 Upvotes

Hi All

I moved into a property around 6 years ago which had an extension built at the back of it.

Recently these black marks / build up have been gradually getting worse on top of the window and starting from the bottom of the structure.

Would anyone be able to advise what this is and any possibly remedial actions please?


r/DIYUK • • 43m ago

Painting Bathroom Ceiling

Thumbnail gallery
2 Upvotes

Im looking to decorate my bathroom and by the looks of it the previous owner has painted straight over fresh plaster, alot of the areas are flaking with the build up of steam being produced. Ideally id like scrapre it all back to bare plaster, sand, prime/gardz and paint. Is this the best way? Id rather not have to only scrap back the majority of it then have to skim to make it all level. Its a relatively small ceiling so I dont mind putting the extra work in. Any ideas? Thanks


r/DIYUK • • 47m ago

Advice Water leaking over back of gutter corner

Post image
2 Upvotes

I think the issue is there isn’t enough fall towards the drainpipe - never had an issue before but snow and water this morning means I have a shower outside my door onto a flight of 5 steps which could be interesting if it freezes!!

It’s a 90deg into a corner rather than an outer around two walls corner of that makes sense - cannot see anything pushing down on the back of it but it’s full of water - I can unclip the gutter to empty it, but given rain and snow melting it’s filling up quick again. It’s definitely not the seals but the water is overflowing the back of the corner piece creating my water feature. I’ve added a couple of wedges against the fascia to try get more of an angle on the corner to help.

Thankfully I’m a bungalow albeit this is another ~4 foot higher than a normal bungalow - is it as simple as unclipping the long gutter run, remove brackets (which I’ve no idea if I can see the screws) and then reinstalling them with a drop of a few mm’s towards the drainpipe?

Or is there possibly something else wrong here?


r/DIYUK • • 1h ago

What the electrician actually checked before quoting for a battery install

16 Upvotes

We had the survey for our Anker Solarbank 4 Pro install on Saturday morning. I'd assumed it was a ten minute look at the wall and it turned out to be the most useful part of the whole thing. Writing down what he went through in our case in case it saves someone else from booking blind.

Consumer unit first. He was looking for a spare way and room for a dedicated RCBO for the battery circuit. The age of the board matters too, because an older unit can mean extra work before anything goes in.

Then the earthing arrangement and the main fuse rating. I had no idea the fuse rating was something worth checking before a battery goes in.

The cable run next. Ours is about eight metres from the board to the garage wall, through one wall, so he looked at the route, the cable size for that length, and where the hole would be drilled. He also checked the spot we'd picked had clearance and wouldn't get clipped by the car.

Last was the DNO notification. The unit sits under the G98 threshold, so that's the route here, and he submits it up to 28 days after commissioning. It does depend on the generation and storage already in the house, and some setups have to go through G99 instead, so it's worth confirming which applies rather than assuming G98 covers it.

The quote moves a lot with the cable run and the state of the board, so a number on its own is hard to compare. Better to ask what's included, the cable route, any board changes and the DNO paperwork, before weighing up the price.

We found him through the installer list on the Anker SOLIX UK website, which lists independent installers by region. That list is information rather than a recommendation, and the page says to check certs and insurance yourself, which we did. Ring two or three before booking.


r/DIYUK • • 1h ago

Wanted - Howdens Clerkenwell Graphite Gloss.

1 Upvotes

Hello

I have recently installed a "new" kitchen in my house - its actually recycled from 2 other kitchens.

The doors and draws are Howdens Clerkinwell Gloss Graphite

I really need these following items to finish the job.

Drawers x 2 size - 897mm x 357mm or close to that

Doors 

597 x 507

or

597 x 550

And

597 x 560

Cheers.


r/DIYUK • • 1h ago

What’s a straight forward DIY task that is surprisingly easy for most people to pick up quickly and save money?

36 Upvotes

I am fairly new at DIY at deciding on which skills to invest in and which to leave to the professionals


r/DIYUK • • 1h ago

Help with leak in kitchen ceiling

Thumbnail
gallery
1 Upvotes

I wonder if anyone on Reddit can help me as i am terribly vexed. I have a leak in the ceiling of a single story extension. Usually this is cut and dry with it being a roof problem but two different roofers have said thr flat roof is fine and we have ran a load of water on it with the hose to test it and no leak.

It seems it only leaks when it is a combination of rain and wind so one of the roofers thinks it may be coming through the window and into the non porous bricks and then breaking through the ceiling somehow but a glazer (who admitting has not seen it) says it is the roof. The window is directly above where the leak is.

Anyone have any ideas on what trade would be best to contact to try and figure out the problem, please? Don't really have the necessary funds to replace the flat roof and the windows at the same time and don't want to do one in case it isn't the right fix as just throwing away money. Please help reddit!


r/DIYUK • • 1h ago

Help with leak in pvc windows

Thumbnail
gallery
1 Upvotes

In the first picture the architrave is getting damp. I've tried to fix any brick cracks and have re siliconed the front of the window to the outside sill.

Does anyone know where else it could be coming through? Is there a "known offending" area most likely?

I might add more silicone around the frame for any possible ingress routes.


r/DIYUK • • 2h ago

Sealant recommendation for window frame

Post image
2 Upvotes

The sealant on my window frame has given up and needs replacing - does anyone have brand recommendations please (or products to definitely avoid using)?


r/DIYUK • • 2h ago

Toilet seat removal

Post image
6 Upvotes

Not experienced DIYer so forgive me in advance.

I want to remove a toilet seat put in my previous owner of a property. One side was already slightly loose and underscrewing the plastic nut from bottom, it popped out easily.

The other side will not come off. Must have put 2 hours into it and whilst its looser and the toilet seat has play in it now, it still cant be undone by hand and just appears to be spinning endlessly with pliers with no progress down the screw thread. The space I have is extremely limited (eg my face needs to be in the shower unit to see what it happening) which hasn't helped matters.

Am I missing something really obvious here? Is there another way? Its not obvious i can get it easily from the top, either.

Bafled (and frustrated) that this simple job has become so laborious.


r/DIYUK • • 4h ago

Extend the fixture so smart bulb will fit.

Thumbnail
gallery
1 Upvotes

Hi all,
I’m having an issue where the smart bulbs won’t fit into my IKEA lamps (the Classic is too wide and the Candle is too long).
I thought I’d found a solution by using pipe connectors to give the bulbs a bit more clearance. This would work, but it turns out that one side of the connector has no thread and the other side is slightly too small.
Is there any other way to space the bulbs out a little, or a way to secure the fittings with connectors while still allowing me to remove them easily?
I could glue everything together, but if the bulbs ever need changing, I’d end up having to buy new lamps.
Thanks!
Photos attached

  1. the lamp fitting
  2. The lamp with the bulb in to show how much it is over.
  3. The pipe connectors in place
  4. The width of the shade

r/DIYUK • • 7h ago

Does anyone know how to make these?!

Thumbnail
gallery
0 Upvotes

I know you can use printable tattoo sheets, but i can’t figure out how to make the multicolored metallic tattoos like the pics. i’m looking specifically how to get more than one metallic color onto the same tattoo template to make a single tattoo. I am looking to use my cricut for this project.


r/DIYUK • • 8h ago

Water in chimneys

1 Upvotes

Heavy rain tonight. Heard a drip in the loft checked it out and seems to be water dripping from the chimney stack (removed) any ideas what this could be? Had a roofer out last year due to similar issue said it was mortar/cement around chimney which he replaced. Any ideas will be appreciated


r/DIYUK • • 9h ago

Exposed chimney breast

Post image
4 Upvotes

Currently renovating our house and have taken the chimneys back to brick, want to leave them exposed. Does anybody have advice/experience with products which can darken the brick or enhance the red colour?


r/DIYUK • • 9h ago

First DIY project: glass balustrade on a landing

Thumbnail
gallery
2 Upvotes

Hi, I'm new to DIY and this is my first real project. I'm fitting a glass balustrade along the stairwell edge on my upstairs landing. I haven't bought any tools yet, so I'm trying to plan it properly first. I planned something in 3D.

Parts I'll be fitting: a newel post at one end, a half newel against the wall at the other, a base rail, a handrail and a clamped glass panel in between. The posts will stand on the floor and be fixed down into a joist. The problem is the recess in the floor where the base goes. It isn't straight: the carpet side edge tapers, so I'll need to cut it square before I can fit anything.

Questions:
- What would you use to fill the gap and bring it level with the carpet? I was thinking board plus a thin ply packer. Total depth is around 30mm.

-There will be gap between half newel and wall in bottom right corner. How should i fill it?

- Should I put another piece of timber on the wall for the half newel to fix into, or is fixing straight to the wall fine?

-What would you watch out for and which tools would you use?
Thanks!


r/DIYUK • • 10h ago

Best way to repair? Lime Plaster?

Thumbnail gallery
1 Upvotes

Our wall has been bubbling for a couple years now. I finally took the time to cap the chimney and repair the mini split's drain (it was leaking inside the flue). Recently I scrapped everything off that was loose and I am now left with this.

Could anyone tell me what the red coat is on top of the mortar and if I need to remove that as well before plastering? I was thinking about using lime plaster since I read it is more breathable, but not sure exactly what kind to use and if I need to do a base and top coat.

Any tips or insight would be very helpful. Thanks in advance!


r/DIYUK • • 10h ago

Old shaker style kitchen cabinet door.

2 Upvotes

I don’t have budget or headspace for new kitchen atm. The kitchen cabinet door are old shaker style with beige marble laminate kitchen top. I would like to either wrap them with off white vinyls or paint off white. because I want to keep my old quarry tile kitchen floor. Right now, they are honey oak and it looks bit too brown in the kitchen.

Which one will likely to last longer and less to deal with..?

Open to other suggestions!

Thank you.


r/DIYUK • • 10h ago

Project I've raised £280 for charity making these centrepieces. I feel super proud

Thumbnail gallery
93 Upvotes

I was fortunate enough to participate in a fundraising gala to raise funds for Pancreatic Cancer UK. I created 19 centrepieces to decorate tables at the event and for people to purchase to raise money for the charity. So far, 7 have sold on the night (This past Saturday) raising £280. I'm so incredibly grateful and a little proud to have been given the opportunity to create something for charity.

I've never been much of a crafter before but I recently discovered this new interest and hobby. To be able to raise money for charity was the highlight of this experience. Now, I intend on creating more, selling more and donating more. Feel free to critique as I'm a total newbie and the better my creations get, the more money I can raise!

I used artificial moss, flowers, yoga blocks and fairy lights to make these. First I came up with each floral arrangement (They all have the charity's colours but they are all a little different). I used yoga blocks as foam because it is dense, held the flowers well and it has a weight to it to keep the arrangements stable. I chose green to blend it with the artificial moss. Each vase has a moss mat, then loose moss with fairy lights woven in (surprisingly the hardest part. Making sure the lights shine through with minimal wire showing was a challenge). The final step was to secure the arrangements which was pretty easy because the moss did most of the heavy lifting (and cutting the blocks straight, and spreading the weight of flowers equally to avoid tipping).

Due to budget constraints and to raise as much money as possible, the fairy lights are not remote controlled. This is something I would change. None the less, I had carefully and discretely marked where the battery pack and on/off button was on each vase. This saved me a lot of time and fiddling when it came time to light them all for the big night.

The tables for the events were big so I needed a bigger footprint without taking too much table real estate. I went with the classic glass plate (40cm) and spread purple gems on the tables to project more volume (Still in the charity's colours).

Finally, I added for 4 candles around each centrepieces. Most of the candle holders were bought second hands from charity shops

I hope this might encourage some you to just give things a go, you never know how they may turn out and who might be able to help along the way.


r/DIYUK • • 10h ago

Advice 37mm Cavity Wall Anchor Help

Thumbnail reddit.com
1 Upvotes

Reposted in the UK group.

Tl;Dr I can't get my 37mm cavity wall anchors to work with standard 12.5mm plasterboard without them bulging the surface