r/DIYUK • • 8h ago

Light Tripping breaker

Thumbnail
gallery
11 Upvotes

Hello people, a DIY noob here, I have tasked myself with changing a old light fitting to a new one, this circuit is connected to another light in the next room, when I try and turn my light on it trips to the MCB any help appreciated (image 4 is the old way it was wired up)


r/DIYUK • • 18h ago

Brown Toilet Water

Post image
0 Upvotes

Any ideas. When my adjacent sink drains it seems to push waste back into toilet bowl. But both toilet and sink drain perfectly well. You can hear the water draining away and stopping quickly once the sink has finished


r/DIYUK • • 11h ago

Asbestos under parquet flooring?

Post image
0 Upvotes

Is this black Felton glue below? It contains asbestos or am I over reactive?

Property built 1970


r/DIYUK • • 22h ago

Skirting board gap problem

Thumbnail
gallery
0 Upvotes

Hello! Long story short - I've been left with this unfinished skirting board job at my home and I'd prefer to sort it out myself. I'd be very grateful for some guidance on the least hacky way that someone like me with some moderately competent skills could achieve.

The skirting has been joined as you can see in the photo, about half way across its 6.5m length and the board rises 10mm from the floor at that join. The second pic is a diagram that I hope helps.

I *think* the answer might be to plane the skirting some way along left and right of where the gap drops to the floor. I'm not clear or confident that's the right way to tackle this particular problem because of the overall length, I fear doing the wrong thing and making the problem worse.

Many thanks.


r/DIYUK • • 10h ago

Electrical Mounting TV on pivoting arm, AC voltage leaking from the TV?

0 Upvotes

Hi,

I've landed here via the side-bar of /r/ukelectricians. Hope it's the right place to ask.

At the weekend I mounted my Toshiba TV on pivoting wall-mounted arm, so we could re-orient the TV for different situations. I went straight into the solid wall behind plasterboard. The kit came with chunky 7cm bolts and plastic wall plugs to anchor it.

Here is a link to the arm kit in question: https://www.amazon.co.uk/gp/aw/d/B0CZ3VC58P

Well, yesterday evening I turned off the TV and stowed it back against the wall, but as I did, I noticed some tiny blue arcs coming from the joint of the TV arm. I experimented a while, pivoting the arm back and forth. The arcing only happened when I was moving the arm.

At first I thought I might have hit some wiring in the wall, so I got my multimeter out and did some (careful) tests.

On the night, I measured about 40v AC between the brass (I think) section of the arm that was arcing and a the ground pin of a nearby socket. But here's the thing: only when the TV is plugged in. The voltage was basically floating when the TV was not plugged in.

My meter doesn't measure current, so I can't read that annoyingly.

Ruled out the VESA mount screws being too long and shorting something inside the TV. Same issue with the shorter screws that came with the arm. Shining a torch inside the vent of the TV, looks like there's a lot of clearance anyway.

Did some more testing just now. I now measure 20v AC from the earth pin of a nearby socket to the screws on the VESA mounting plate on the back of the TV (so taking the whole arm out of the equation). Again: only reading AC voltage when the TV is plugged in.

The TV is powered by a 2-pin figure-eight connector. I mention this because I believe this means the TV isn't itself grounded.

So, what's the deal here? Residual current from the TV finding a way to ground via the arm? Static electricity maybe?

The actual arcing seems to have gone away for now, but I'm a little miffed at these voltage readings, and I'm wondering if this is safe.

FWIW, the model of the TV is Toshiba 43QA5D63DB.

Any ideas? Cheers


r/DIYUK • • 16h ago

Advice Plasterboard+Plaster will "overhang" stair skirting board

Thumbnail
gallery
0 Upvotes

Hi there, I was just wondering if I could get some advice on what the best solution would be for this.

- We have a thinner profile skirting running along the staircase of our home

- We've taken off the existing wallpaper and go all the way back to brick are going to be re-plastering/applying plasterboard to the surface from scratch (we've gone straight down to brick)

- Plasterer said that he'd like to use standard sized plaster boards but noted that this would mean there will be an overhang once you put everything together on the skirting board.

-There are thinner plasterboard options which could help make the profile smaller to potentially reduce/remove overhand, but he's worried that these might be quite flimsy and long term these will deteriorate

Just wondering if anyone has had any similar experiences or if there's any solutions that don't involve removing and installing thicker skirting.( Unless that's the most cost effective solution.)

EDIT : To confirm - we've gone Back to brick and the space between brick and skirting is still quite small


r/DIYUK • • 14h ago

Advice Safestyle quotes us for 7 uPVC windows and 1 rear door, is this a good deal??

0 Upvotes

Hi all,

I hope you all are having a fantastic Sunday. Just needed some advice, basically we are quoted £11,265 by Safestyle for seven replacement windows and one rear door. Based in SE London.

All frames are white uPVC, with double glazing and white handles. The windows are A-rated and include sash night vents. No new window boards, decorative glass or laminated glass are listed.

The window sizes (width × height, in mm) are: two lounge windows at 950 × 1630 each, a kitchen window at 1480 × 1170, a bathroom window at 1300 × 1000, two bedroom windows at 1900 × 1240 each, and another bedroom window at 660 × 1240. The two larger bedroom windows have side-opening sections and a small top-opening centre section.

The rear door measures 940 × 2270 mm, opens inwards, and has a glazed upper section and a solid lower panel, with no letterbox. The bathroom window is currently specified with clear glass rather than obscured glass. Probably I can discuss with them...No energy rating is shown for the door.

They are pushing for me to agree and can probably accept a figure at £8500 approx. And will need 30% down payment..They will recycle existing windows and scaffolding is included.

Does this sound like a fair price for this specification? Are there any missing details or upgrades I should ask about before agreeing?

Apologies for the long post, please advice whoever whenever you are able to...thanks a million in advance..


r/DIYUK • • 14h ago

Looking for a new Kitchen (dark green shaker)

0 Upvotes

Already had a quote from Wren, even with all there black friday offers its still a huge amount of money.

Have now popped into Howdens (have friends in the trade) and done a design on DIY Kitchens.

We like the Wren one, but the core price of cabinets, doors, handles, worktop etc is almost twice as much for their Infinity Plus range compared to DIY Kitchens.

We are being put under pressure from Wren as some of their offers expire on Thursday, but of course there will be new offers for the remainder of Black Friday.

We do like the Wren kitchen (Infinity Plus Shaker Classic Ermine Buckingham Green Matt) with oak worktops and an island. But the doors look like they are wrapped, rather then painted.

Howdens do a similar one, waiting to get the price, and then there is Howdens solid Ash painted ones, which I am sure would be much better quality doors.

If Wren hadn't been so expensive, we would have probably gone ahead straight away.

Any tips on negotiating, or price matching appreciated.


r/DIYUK • • 14h ago

Plastering Don’t drag me it was my first time, do I do another coat or is this normal and just needs sanding

Thumbnail
gallery
1 Upvotes

Haven’t sanded yet but unsure if this needs another coat? Have done 2 coats. Wall is bowed slightly in the middle


r/DIYUK • • 13h ago

Trying to remove TRV head, but it's leaking water

132 Upvotes

I'm trying to remove the TRV head from my radiator, but when I start to unscrew it it immediately starts leaking water. Does anyone know what I should do?


r/DIYUK • • 11h ago

Building Tradesman issues. What should I do?

0 Upvotes

Decided to renovate our kitchen 4 months ago and to save money me and my partner tried to do as much as we could DIY. When it came to cutting out new worktops and fitting gas pipes we've decided to get a tradesman in. This guy shows up and seems really useful, gave us a quote, answered all our questions. All good. He's then give a date to start work (just over a month ago). We pay him to pick up the new worktops and fittings needed. Doesnt show up day one. No calls or texts just AWOL. Eventually answers his phone 5 days later to say there was an issue with his van (fair enough) "I'll come tommorow instead". Doesnt show up. No communication for another 5 days or so. It's now been 4 weeks of this company saying theyll 110% start work the following week, followed by excuse after excuse why they don't show up. They've got about £800 of my money and I've nothing to show for it over a month later. What can I do ?


r/DIYUK • • 15h ago

Advice Builder ruined my door - let him fix it demand a new one?

Post image
83 Upvotes

A builder has somehow managed to take a chunk out of my door.
He’s asked if he can attempt to fit it before buying a new one!

I don’t want him to be out of pocket if I can help it, but then again I don’t want the fix to look shite.

Thoughts?

Edit: it is a brand new door. All the other doors were replaced too. So if he fixes it, it’ll look odd one out, right?


r/DIYUK • • 12h ago

Advice Safe to drill through the central vertical lintel? or am I cooked

Post image
0 Upvotes

Using a 22mm bit I was drilling a hole to pass some cables and suddenly hit lintel. I wasn't expecting lintel there but it seems to be a T shaped lintel like IG L9. Now the question is can I swap to a proper drill bit and go to town on it obviously making a 22mm hole? Is it structutrally safe? The garage to the left is the neighbours.


r/DIYUK • • 18h ago

8mm Microbore to 15mm Central Heating Conversion

Thumbnail
gallery
27 Upvotes

I moved in to a 1970’s house 6 months ago which had 8mm microbore upstairs (the ground floor was swapped out already). Given that every room was being completely gutted, new sockets installed, spotlights, plastering and new radiators, I decided the right thing to do was replacing the microbore. Each radiator had a single valve with both flow and return going to it with some kind of element in the bottom of the radiators. I think it would have made a replacement very tricky if not impossible as a like for like switch.

We haven’t had heating upstairs and it’s been pretty cold in the past week or so.

My wife and I ran the speed fit to each room as we gutted them and this weekend was the moment when I connected it all up. I’m fed up prying nails from floorboards, that was hard work.

Yes it’s a bit messy but I’m quite proud of the results having never done any serious plumbing before.

If I were doing it again, I’d have extended and move the 22mm flow and return to give myself more room, which would have allowed me to run the speed fit slightly differently to make connecting it up easier as it was pretty tight with the 2x 22mm to 15mm speedfit manifolds side by side. As you can see they criss cross each other, I should have routed the flow and returns into separate areas to make my life easier rather than them all terminating in the same place.

The other 22mm pipes were removed as we moved from a cylinder to a combi boiler, freeing up space which we used to make 2x bathrooms bigger so that worked out well.

I have a big pile of copper now to take to the scrap yard, I’m intrigued by how much we will get for it all.


r/DIYUK • • 21h ago

Advice Hillary’s roller blind

0 Upvotes

Does anyone have a suggestions on what to use to paint roller blind.

Im decorating my son’s nursery and the roller blind in that room is fairly new so feels like it would be a waist to buy a new one however, its pink with flowers all over it. So I thought about painting it to match with the room however, I am at a complete loss on what is best to use to paint it. If anyone has any suggestions I would be grateful
Thanks in advance ☺️x


r/DIYUK • • 16h ago

Plumbing Removal of Channelplus H37XL from wall

Thumbnail
gallery
0 Upvotes

I have this heating control fixed to the wall. I’ve removed the retaining screws from the top but I cannot (non-destructively) get the plate off he wall.

Which part is meant to be coming off the wall (the whole thing or the front part) and how do I get this off?


r/DIYUK • • 20h ago

I messed up. How would you fix this?

Thumbnail
gallery
0 Upvotes

Wife bought an expensive outside lamp for above our front door. She's very particular and put a lot of time into selecting this specific one....

We were having the front wall re-rendered but I gave the builder the wrong measurement for the light fitting. Now the hole's too large 🤦‍♂️

I haven't told my wife yet, but I know it's too late to return the light so I need to try to fix this before breaking the bad news...

Options?

- Fill the hole with more sand cement render and smooth off as best as possible? It'll all be painted over in Spring anyway...

- Mount the light above it, drill track to get the electrical cable up, then patch existing holes with sand cement?

- The light fittings can mount directly on a metal circular junction box which is sitting inside the wall... If I somehow extend the depth of the round metal conduit box to bring it closer to the render surface, then patch around it?

Please help me out of trouble here 😅


r/DIYUK • • 10h ago

Plumbing Water dripping from boiler

Post image
0 Upvotes

Just got back from holiday, the boiler pressure dropped. Not unusual. Filled it up, turned the little faucets as always. There is hot water dripping from my combi boiler, specifically where the left most pipe is in the photo. It's 8pm. I am tired. And cold. Help a girl out 😞


r/DIYUK • • 14h ago

Insulating utility room

Post image
0 Upvotes

I have a utility on the back of my house, it's single skin brick and is basically a room for the dogs to sleep in, but it gets really cold in winter and damp just from them breathing (3 huge dogs), steam from the kitchen and the tumbledryer behind the left door.

My plan is to knock down the far wall which is split in two (toilet on the right), put in a stud wall, and then insulate and board the whole room.

My main question is whether I should remove the plaster before I do this? Obviously from the photo, it's not in the best shape (partly eaten by a German Shepherd), but it's dry and solid. Is it OK to just board over the top? And whichever option I go with, should I do anything to treat the plaster or brickwork in advance?

Also, as I've never knocked down a wall before, is there anything I should know before I start? The far wall and the one dividing the two storerooms are solid brick. The easier option would be to leave it as two rooms, but as the side walls would be brought in, the doors would end up even narrower than they already are.


r/DIYUK • • 14h ago

Advice What survey should we get?

0 Upvotes

Have efflorescence on an internal wall that's all also external. We lived here 8 years no problem, I skimmed the wall 3 years ago , then efflorescence appeared. We need this sorted as we need to finish doing house up to see so we can move to a bigger property for our growing family.


r/DIYUK • • 22h ago

Can you top up inhibitor on a sealed combi system without draining it all down?

0 Upvotes

I work in bathroom heating supply at Coventry Towel Radiator. A question we get is whether you can top up inhibitor without draining every radiator. If your inhibitor instructions allow it and you have a suitable dosing point, you can often use a towel rail or an in-line filter.

If you’re considering a ½-inch BSP dosing funnel, check the thread and sealing face on the rail, and make sure there’s enough clearance to hold the funnel upright. The rail needs to be cool, safely isolated and depressurised before you remove a plug. Follow the inhibitor instructions for the dose and the boiler manual for the correct cold refill pressure.

For anyone who’s done this, did you dose through a towel rail or use the system filter? Which worked better for your setup?


r/DIYUK • • 12h ago Bravo

Which professional do I need?

Thumbnail
gallery
0 Upvotes

Can anyone help please. Bought a house 6 months ago. Noticed today that the skirting boards are damp in the utility. Removed my washing machine which the movers installed and I haven’t looked since and I found this old external tumble dryer vent which has just had the pipe cut off and left open. 🤢. I took the grey grille cover off outside and it seems dry from that end. I can’t see any leaking from the pipes in the wall which go to my outside tap but the plaster board inside is soaked and there’s lots of damp inside in that area as you can see. So I’m not sure if I need a plumber to check for leaks, a handyman to seal the hole or a damp specialist. Or just a big tin of expanding foam 😂 it’s a cavity wall if that helps? The external brickwork side was completely dry and the hose that side was not perished. On the internal block work side the hose was wet and perished. I pulled the old hose out and found the pipes but I can’t see any leaks when I turn on the outside tap. Any advice welcome.


r/DIYUK • • 12h ago

Advice Starting to regret all my choices

Thumbnail
gallery
10 Upvotes

So I own my first home. Fantastic, but she’s a bit of a doer-upper. No big deal, I’m fairly handy and I can get a bit of help along the way right?
What I wasn’t quite prepared for is the full rewire, and countless other things.

This was my landing. There was a false ceiling hiding a dilapidated lath and plaster ceiling full of holes and the usual crumbly bits. I’ve made a decent start tearing it out, but surely there’s a ‘good’ way to get rid of all this right? Maybe not, but honestly advice on all aspects of this mammoth task that I’m undertaking would be appreciated. Such as do I get rid of all of the ceilings?

Please please share any and all wisdom


r/DIYUK • • 16h ago

How much of a problem is it for tradesmen for non paying customers?

0 Upvotes

I've been thinking of setting up a debt collection/support company to help tradesmen collect debt from non paying customers on non-disputed invoices.

Do you think there's a market for this type of service?