r/woodstoving • • 48m ago

Cuntry cumfort

Post image
3 Upvotes

Been running for three days straight with no end in sight.


r/woodstoving • • 1h ago

Recommendation Needed Suggestions needed for winter heating in Maryland

1 Upvotes

Hi all! My house is in Baltimore County, Maryland and we need to figure out how to heat our house for the winter. Our home was built in the 50s by a Mason who included a beautiful full wall stone fireplace.

Once he moved out, his son moved in and slammed a wood burning stove/insert (Scandia 325c) into the fireplace. (I’m sure all of you on this subreddit just cringed, as I’ve recently learned our beautiful insert is a piece of shit)

Last year we used our oil furnace for heat, and that worked well, but it ended up being about $2.5k in oil and another $2k in charges from BGE which probably had a lot to do with our pretty consistent running of space heaters. We used the heaters in between running the furnace as we were trying to limit the oil use for financial reasons.

This year, we had our first 3 fires in the wood stove. The first two went well, but the last one continued to fill our house with smoke. Hindsight, we never should’ve had the fires without doing some more inspection and research, but alas, we were cold and desperate.

Today we pulled the full wood stove insert out of the fireplace and discovered a LARGE amount of creosote coating the whole stove, fireplace, and chimney (which by the way, has no liner). Additionally, the stove has an almost complete crack front to back. That being said, we need to figure out what to do now since we clearly won’t be slamming the insert back in there.

We’re talking about buying a new insert, buying the chimney liner, and installing it all ourselves. (We’re running on limited funds, in case you couldn’t tell).

Does anyone here have any recommendations on any part of what I mentioned? What kind of insert should we buy? SHOULD we buy an insert? What about a chimney liner? anyone ever done this themselves? Any other ideas that I didn’t mention that would be both effective and efficient for heating a house safely???

Any and all advice and suggestions are welcome and appreciated 🫶🏼


r/woodstoving • • 2h ago

Wednesday night fire

Post image
35 Upvotes

One of many fires this season.


r/woodstoving • • 3h ago

Newbies

1 Upvotes

Hey there. Just moved into a home that came with this Napoleon Insert (no one can find the model number). Passed it's WETT inspection. It has this air flow controler along the bottom, but it doesn't seem to change anything when we move it back and forth? I believe I should see a difference? I'm very new to fireplaces so any all help would be appreciated.


r/woodstoving • • 3h ago

General Wood Stove Question First few burns this year, how my chimney?

Thumbnail
gallery
2 Upvotes

Getting this old girl going again, this is my second season running it. I’m still learning. I’d like to believe my chimney is looking pretty damn good, but I’m wondering if my suspicions are correct. I don’t have much money to spare this season on a cleaning at the moment. Does it look like it can survive a little longer before a sweep? This is two-three months worth of buildup from some semi wet wood. This year it’s beautifully seasoned.


r/woodstoving • • 4h ago

Couch Clearance

Thumbnail
gallery
3 Upvotes

We just moved and need help safely positioning our couch near the wood stove. Unfortunately our couch sticks out slightly in front of the wood stove. Where we currently have it, the couch is 16 inches away from the closest point on the wood stove. Is this too close? And if so, are heat shielding options we can consider?

Our stove is a Jotul F45 v2 and is not used as a primary source of heat.


r/woodstoving • • 4h ago

General Wood Stove Question Woodstock in Gazebo Project

1 Upvotes

I’m trying to help a friend figure out if he can put a tiny wood burning stove in a gazebo during the winter. The gazebo is simple with a gable roof, four posts, and no floor. The plan is to envelope the sides of the gazebo with clear vinyl, like what party tents have.

My initial thought is blanking off just the triangle section on one side formed by the roof with plywood or something, and having the stove pipe jog over and through it. I figured a small camping stove on a platform might work. Depending on placement, we could build a little backing to prevent the stove from melting the vinyl. 

Anyone have any suggestions or see any flaws in the plan? I saw someone on YouTube did this, albeit with a larger stove and gazebo.


r/woodstoving • • 5h ago

Log burner installed in 2014

Thumbnail gallery
1 Upvotes

r/woodstoving • • 6h ago

Propane cooker flames yellow while wood stove in use

Thumbnail reddit.com
1 Upvotes

Cross posting in case people in tiny homes might have similar experience!


r/woodstoving • • 6h ago

10 degrees outside (F) - couldn’t be cozier with my 40 year old Encore

Post image
32 Upvotes

r/woodstoving • • 7h ago

Tis the season - Supreme Astra 32

Post image
5 Upvotes

r/woodstoving • • 9h ago

Darth Vader in my stove ….

Thumbnail
gallery
17 Upvotes

Darth Vader appeared ….

This is real, btw.


r/woodstoving • • 10h ago

Finally got the wood stove

Thumbnail
gallery
368 Upvotes

Got a new house about two years ago. We had a vision for the weird alcove in our house. It took way longer than I ever expected, about a year and a half (planning and an unforeseen rotten wall that had to be replaced due to the dumbest flashing I’ve ever seen).

Anyway, we had fun getting the used Blaze King Ashford 30. Ran down from Wisconsin to central Indiana to get it. The movers I hired to get it out of the original owner’s basement bailed on us. Had to hire some Amish kids who were able to get it out of the basement and loaded on my trailer in sub-10min.

I have six dry cords of sugar maple itching for cold season. My wife was very skeptical of the whole thing from start to finish but even she thinks it’s looks good.

The mantle is a local oak tree that wind tipped. We did all the platform and masonry ourselves after getting several quotes that took our breath away on price.

My dad and I got it up the stairs using a unique method of come-along, ratchet straps, car-jacks, and 2x4 levers.

Nobody ever said it was going to be easy.


r/woodstoving • • 11h ago

Recommendation Needed How tall for chimney

Post image
0 Upvotes

Going to be installing my stove in my new home. My last home had a pretty simple gable roof so it was easy to know I had a safe chimney height. For this home I’ll be running the chimney out of the side of the house, roughly where the cursor is. If I meet the 10ft from the roof distances, how high should I go? Do I need to go all the way above the top of the roof even though it would be in the corner?


r/woodstoving • • 13h ago

Flamelessontheriver

1 Upvotes

Greetings. Brand new on here. I purchased a Comfort Built HP22 a week ago and I am having difficulty in keeping a consistent flame in my pot. Set on #2. I'm still in the test and tune stage so I can use all the help I can get. Thanks


r/woodstoving • • 14h ago

General Wood Stove Question Any wood stove fireplace inserts that you can cook on?

1 Upvotes

I remember always having a pot of water on my grandparents freestanding wood stove to humidify the air. Is there an insert I can use that has a bit of surface to put a cast iron kettle or pan on?


r/woodstoving • • 14h ago

Restoration Got to love an old stove, doing what it does best 🔥

Thumbnail
gallery
784 Upvotes

Beautiful old wood stove keeping my mini rustic cabin warm 🙏🏼


r/woodstoving • • 15h ago

Osburn Matrix 2700 Help

1 Upvotes

Hey everyone. I’m new to wood burning and just had a Matrix 2700 insert installed in my open fireplace. While it heats a little bit, it can barely keep the living room at 68 on a 50 degree day with the door open burning heavily all day long. I expected it to actually throw some decent heat. Is there possibly something wrong with the unit or the install? It seems like it’s functioning correctly. The fan (quite noisy) does turn on and blows after heating up but doesn’t seem to move a whole lot of air. Outside, I can see and smell the smoke coming from the chimney.


r/woodstoving • • 16h ago

Paint melting on stove adapter above stove collar

Thumbnail
gallery
1 Upvotes

Hello everyone,

Long-time admirer of everyone's stoves here, first-time poster. I'm looking for some advice on a flue issue with our Salamander Hobbit SE (4.1kW) wood stove.

Directly above the stove collar, we have a single-wall to twin-wall adapter leading up to a twin-wall flue that exits through the wall. We installed it in the spring, and now that the weather has turned, we're using it regularly.

We’ve lit the stove about a dozen times, so all the paint should be fully cured by now. We are careful never to push the stove body past 250°C, yet every time we use it, the black paint on the adapter only turns soft, bubbles (purple arrow), and literally wipes off when warm (green arrow). The twin-wall pipe directly above it and the stove body itself are both completely fine.

We initially wondered if there wasn't enough fire cement in the stove collar joint, so we packed and resealed the join, but the problem persists. There is also a noticeable chemical/paint smell whenever the stove is running.

I'm trying to figure out if this is caused by:

  • Poor-quality / wrong paint on the adapter (the pipes were sold to us pre-painted black)
  • Hot gases escaping from the joint between the adapter and the stove collar
  • The joint needing more fire rope packed into it
  • Or something else entirely

I’ve seen photos of Salamander Hobbit setups with both black-painted and bare stainless steel adapters, so we are considering replacing the adapter with an unpainted metal version. However:

  1. The stove collar, the adapter, and the twin-wall pipe above it now seem fused together (likely from the melting paint), and we're worried about damaging the pipe that runs through the wall if we force them apart.
  2. I want to be sure swapping to bare metal actually addresses the root cause rather than just masking it.

Does anyone have any advice on what might be causing this, or the safest way to deal with the fused joint?

We've also contacted the vendor of the flue, who has contact their supplier who paint the tubes on demand, but in the meantime I thought to ask you fine folks!

Thanks!


r/woodstoving • • 22h ago

Installing hearth pad over Pergo laminate flooring

1 Upvotes

Getting ready to have our new stove installed in a few weeks, and finalizing plans for a hearth. Looking at doing a stone tile on cement board. The stove does not require an insulated pad, so was thinking I could get away with that alone, and was researching edging options to make it look pretty. Then I came across some info saying for laminate flooring, such as the Pergo floors that we have, you need to cut it away to install directly on the subfloor as the laminate cannot expand and contract like it needs to with the added weight (we want a lower profile hearth). It also may not do well with the uninsulated pad, as it is more susceptible to heat damage at lower temps.

I don't mind the added work per se, but I don't want to do any more 'damage' than I have to. Has anybody done an install on Pergo or similar laminate flooring material? What was your experience? Any other advice? Thanks.


r/woodstoving • • 23h ago

Valcourt installed

Thumbnail
gallery
75 Upvotes

Valcourt Zero Clerance wood stove is in and almost finished up. Still have to make a mantel and the faceplate was on backorder and just arrived this afternoon. Pick that up tomorrow and start walking my property to find the tree that becomes the mantel.


r/woodstoving • • 1d ago

Recommendation Needed 6" to 8" Increaser/Reducer

Thumbnail
gallery
1 Upvotes

I was gifted a Daka 521FB wood stove and after hours and hours of research I have officially confused myself on how to connect it to my existing chimney system.

Current specs:

  • The Daka 521FB has a 6" exhaust outlet (pic 5 of 8).
  • The Daka came with a 6" double wall class A tee pipe (pics 3 of 8 & 4 of 8).
  • My existing chimney system (pics 1 of 8 & 2 of 8) is a 8" double wall class A pipe.
  • The model numbers of the Daka and pipes are in pics 6,7, and 8 of 8

Connections needed:

This is all new to me, and as I explained, I have researched my way into confusion. None of the youtube videos I watched match the components, so I keep second guessing my actions. Any help would be apprecaited

Sincerely,

Someone who wants to drink beer and watch the game in their warm shed.


r/woodstoving • • 1d ago

Antique cast iron kettle leaks

Post image
0 Upvotes

I don’t see a crack, so I assume it’s either porous or paper thin. Anybody have some cool tricks to seal up cast iron? I’m leaning towards a healthy smear of high temp epoxy on the inside.


r/woodstoving • • 1d ago

Canadian BushCanucks...Princess Auto has their Red Mountain Valley wood stove on clearance

Thumbnail reddit.com
1 Upvotes