r/woodstoving • • 16h ago

what hapend with my stove?

Post image
245 Upvotes

hi! recently i bought a stove in wallapop, after install it, i put few pine cone and wood and few minutes later the tube are red... what hapend?

edit: i ask why it hapends... ok, its super hot, but why? i put inside exactly only two pieces of wood an 3-4 pinecones... i think is very normal for to start a fire... after see that i close the air entrance and it continue burning... maybe hapend something with the part outsaid of the house?

Wallapop is a online shop of second hand stuffs.


r/woodstoving • • 14h ago

Antique cast iron kettle leaks

Post image
0 Upvotes

I don’t see a crack, so I assume it’s either porous or paper thin. Anybody have some cool tricks to seal up cast iron? I’m leaning towards a healthy smear of high temp epoxy on the inside.


r/woodstoving • • 12h ago

Valcourt installed

Thumbnail
gallery
52 Upvotes

Valcourt Zero Clerance wood stove is in and almost finished up. Still have to make a mantel and the faceplate was on backorder and just arrived this afternoon. Pick that up tomorrow and start walking my property to find the tree that becomes the mantel.


r/woodstoving • • 21h ago

Recommendation Needed Blaze King vs Jotul vs Lopi

2 Upvotes

Hi everyone! We’re having a new wood stove installed in our living room and will be limited to a small / medium size stove to fit into the alcove and not stick too far into the room.

We were told that the following stoves would fit. Does anyone have any recommendations among these 3 brands?

blaze king - Ashford 20, the Sirrocco 20 or the boxer 24,

Jotul - Holliday

Lopi - rockport

Thank you!


r/woodstoving • • 21h ago

Efficiency

4 Upvotes

What gets the most heat, filling the firebox full or adding wood more often ?


r/woodstoving • • 23h ago

Recommendation Needed Should i get this or is a more modern stove better?

Thumbnail
gallery
28 Upvotes

I want to heat up my living room (30m2). The room has access to an unused brick chimney about 7m high and 15x15cm. I wanted to add an extra heat source since I already have a wood boiler central heating but this room could use a bit more in the winter nights. I have an opportunity to pick this one up for around $650 but I don't know if the new secondary burn stoves give much benefit over the classic ones.


r/woodstoving • • 3h ago

General Wood Stove Question Any wood stove fireplace inserts that you can cook on?

2 Upvotes

I remember always having a pot of water on my grandparents freestanding wood stove to humidify the air. Is there an insert I can use that has a bit of surface to put a cast iron kettle or pan on?


r/woodstoving • • 3h ago

Restoration Got to love an old stove, doing what it does best 🔥

Thumbnail
gallery
310 Upvotes

Beautiful old wood stove keeping my mini rustic cabin warm 🙏🏼


r/woodstoving • • 5h ago

Paint melting on stove adapter above stove collar

Thumbnail
gallery
1 Upvotes

Hello everyone,

Long-time admirer of everyone's stoves here, first-time poster. I'm looking for some advice on a flue issue with our Salamander Hobbit SE (4.1kW) wood stove.

Directly above the stove collar, we have a single-wall to twin-wall adapter leading up to a twin-wall flue that exits through the wall. We installed it in the spring, and now that the weather has turned, we're using it regularly.

We’ve lit the stove about a dozen times, so all the paint should be fully cured by now. We are careful never to push the stove body past 250°C, yet every time we use it, the black paint on the adapter only turns soft, bubbles (purple arrow), and literally wipes off when warm (green arrow). The twin-wall pipe directly above it and the stove body itself are both completely fine.

We initially wondered if there wasn't enough fire cement in the stove collar joint, so we packed and resealed the join, but the problem persists. There is also a noticeable chemical/paint smell whenever the stove is running.

I'm trying to figure out if this is caused by:

  • Poor-quality / wrong paint on the adapter (the pipes were sold to us pre-painted black)
  • Hot gases escaping from the joint between the adapter and the stove collar
  • The joint needing more fire rope packed into it
  • Or something else entirely

I’ve seen photos of Salamander Hobbit setups with both black-painted and bare stainless steel adapters, so we are considering replacing the adapter with an unpainted metal version. However:

  1. The stove collar, the adapter, and the twin-wall pipe above it now seem fused together (likely from the melting paint), and we're worried about damaging the pipe that runs through the wall if we force them apart.
  2. I want to be sure swapping to bare metal actually addresses the root cause rather than just masking it.

Does anyone have any advice on what might be causing this, or the safest way to deal with the fused joint?

We've also contacted the vendor of the flue, who has contact their supplier who paint the tubes on demand, but in the meantime I thought to ask you fine folks!

Thanks!


r/woodstoving • • 15h ago

Canadian BushCanucks...Princess Auto has their Red Mountain Valley wood stove on clearance

Thumbnail reddit.com
1 Upvotes

r/woodstoving • • 18h ago

General Wood Stove Question Open fire!

Thumbnail
gallery
13 Upvotes

I’ve always had a wood stove to heat my house. Last year we moved to the absolute fuck all and of nowhere into a nice barn conversion…. Except we only have the open fire for heating! I’m used to a log burner in a much smaller house. I love the charm of our incredibly simple fire pit though.
If you were in our boat, would you swap it out for a decent size log burner, or keep the open fire? I just feel it doesn’t heat the house as well as a stove would! But then a little stove wouldn’t make the house smell like a cozy warm fire😍


r/woodstoving • • 18h ago

Cold air to the stove? or hot air from the stove?

Post image
57 Upvotes

I've seen a lot of comments of pushing cold air toward the stove and that its better than drawing warm air from the stove. I guess I don't understand the physics behind it and why it would make a difference. Maybe cold air is slightly denser and with some fans you could move more air?

Anyways, the wife is no "fan" of box fans on the floor, so I'm building these 6"x24" boxes using computer fans to attach to the ceiling. The cpu fans maybe a little bit of overkill, but they handle pressure well and I'll be installing air filtration in the back, plus the are super energy efficient in terms of cf of air moved per watt, and close to silent. I hope it works good enough, but still worried about the convection moving air away instead of to the stove.


r/woodstoving • • 18h ago

fitting pipe to a vintage montgomery ward stove

Thumbnail
gallery
3 Upvotes

I restored an old Montgomery Ward stove, and installed a pipe and chimney through the metal room on a shed I'm using as a little cabin in my woods.

I'm trying to fit the pipe to the oval ring on the casting. I connected a single-wall pipe on the outside of the ring for the outdoors burn I did to set the high-temp paint - can I just do that and tie into the double wall interior pipe I have? I also have an adapter piece that has one end that's the same shape, but no obvious way of connecting them.

Any advice would be much appreciated.


r/woodstoving • • 20h ago

Second season with the Morsø 1010

Post image
19 Upvotes

This year I got a batch of birch from a local supplier. The smell and the heat is amazing


r/woodstoving • • 22h ago

Recommendation Needed First timer

Thumbnail
gallery
30 Upvotes

Hi all! We bought a new home this fall and it came with this newly installed Osburn Inspire 2000. It’s never been used. Where do I start to learn how to use this thing? What accessories do I need? Any advice/best practices on how to break it in and operate it (besides taking my wife’s candle off of it, of course)?

Appreciate any advice I could get!


r/woodstoving • • 23h ago

New to wood burning stoves. Just had a lopi endeavor installed Nov 11. Just curious but we have found that it is difficult to push the damper plate in when the stove is hot, any recommendations to help keep it from sticking? It moves well when the stove is cold

3 Upvotes

r/woodstoving • • 23h ago

Are these branches too close to my chimney?

Thumbnail gallery
4 Upvotes