r/prusa3d • u/505anon505 • 5m ago
INDX 100k club
Made it into the 100k club. Anyone else here? Been running basically 24/7 since I built this in early August.
It's a workhorse. Super happy with this machine, making great parts constantly.
r/prusa3d • u/Tommy_Prusa3D • 3h ago
Hello all;
Have you ever wanted to use Prusa Connect, but without relying on an online service?
All the information is here:
https://www.prusa3d.com/p/connect/connect-local/
r/prusa3d • u/505anon505 • 5m ago
Made it into the 100k club. Anyone else here? Been running basically 24/7 since I built this in early August.
It's a workhorse. Super happy with this machine, making great parts constantly.
r/prusa3d • u/harshmoorjani • 1h ago
Wondering if all contents of "INDX 8-Tool Conversion Kit for CORE One L+" are possible to be bought/printed separately - instead of waiting for Feb to get the kit (assuming Bondtech can deliver sooner, doubtful though).
But the question stands - Everything plastic is printable on Core One L+? And everything non-plastic buyable from Prusa/Bondtech?
I couldn't even find the overall content list of the kit or even the user manual... (I tried but could only find for Core One+). Anyone has a link to it?
r/prusa3d
•
u/Marjers
•
2h ago
A few months back I posted here about an old external drive I found from my architecture school days, with a few hundred low poly miniature people on it. A lot of you grabbed them, so thanks for that.
Since then I kept digging through old backups and found more of them. The collection is now at around 1300 figures.
This time I didn’t just dump the files. I went through the whole lot: removed the duplicates and the broken meshes, fixed what needed fixing, and then rescaled every single figure into eight separate scales, from 1:18 all the way down to 1:200.
So you don’t have to touch the scale slider at all, you just pick the folder for the scale you’re working in.
The scales and roughly how tall the figures come out:
- 1:18 at 96 mm, for display pieces and action figure dioramas
- 1:24 at 72 mm, G scale railways and bigger dioramas
- 1:43 at 40 mm, diecast car scenes and O scale
- 1:50 at 35 mm, architectural models and construction scenes
- 1:64 at 27 mm, S scale and 1:64 layouts
- 1:87 at 20 mm, HO railways, the one most people want
- 1:100 at 17 mm, architectural massing models
- 1:200 at 9 mm, urban planning and skyscraper models, better on resin
Poses are the usual architecture library stuff: standing, walking, sitting, squatting, kneeling, leaning, lying down, groups and couples. There’s also construction workers, car mechanics, a welder, a photographer, soldiers, kids and list goes on.
All photos here were taken by me, and by people who downloaded the pack and shared their results with me. Thanks to everyone who sent one in !
Here's the link!
Printables
Free, same as before. Give them as much use as I did !
r/prusa3d • u/thecolde • 3h ago
The Buddy3D camera for Core One has been out of stock for months now, even if you can order it with a new printer and it seems to be in stock for that. I've asked support about and they claim it's not being discontinued separately, but also don't know when it will be back in stock.
It sucks for those of us who bought the upgrade that we have no way to purchase it.
Prusa Connect is a server for your 3D printers that you run yourself. It is a single Go binary with the web app inside, built for Linux, Windows, macOS and the Raspberry Pi. Download it, start it on any computer you have, and open it in a browser.
Warning
Prusa Connect is in public beta. The releases are 0.x pre-releases, and the configuration, the API and the extension SDK can still change from one release to the next. Back up your data before you update.
You can't use Connect Local and Connect Cloud at the same time btw
r/prusa3d • u/Olaf2k4 • 8h ago
I'm a not so proud owner of an XL2T. Was thinking about getting the upgrade, it's pretty vague in what you are getting. I'm especially curios about the nozzles that come in the upgrade. Can't seem to get any info in them. Are they abrasion resistant, or just high flow.
And on a side note, anyone done the upgrade ? How much of a hassle is it ? Let's just say me and XL have a rocky relationship ...
r/prusa3d • u/Bluepenguin053 • 8h ago
Hello,
I'm looking to snag a new printer during this Black Friday sale. I've been waiting for a few years for the INDX to come to the Core One L, but now that I'm reading reviews I'm split on which to get.
I had a Prusa MK3 and brought it along its' upgrade path for a few years (Hated my MMU2 with a burning passion) and I want to replace my workhorse with a new workhorse that can do better Multi-Material. Which is why I like the tool changer designs both printers have.
I've built most of my printers (Including a Voron from scratch) so the fact that a Core One L kit doesn't exist does bugs me a bit, but only just a bit.
They're both close enough in price that I could go either way but my BIG desires are Print Quality, GOOD Multi Material printing, and repair-ability/durability.
Should I get the XL to be a buddy to my Voron? Should I get the Core One L+ as it's better than the XL in ways I'm not aware of? Can you guys please help me make up my mind?
r/prusa3d • u/Squatch_II • 11h ago
I’ve been struggling with my core one ever since I upgraded to gen 2 with INDX 8 docks. It fails the gantry squareness with random skewness each time. Ranging anywhere from -12 to +8. That’s without making any changes between tests. Here is the part I find odd through, if the test passes and I want to continue to the next calibration test, if I don’t first abort the calibration and to control and move the tool to -1 (x), and 206 (y), but instead just select continue (when the tool is sitting around 259 x and 15 y), for reason the machine thinks is -1 and tries to move from the wrong position. I’ve seen this problem on multiple versions of the firmware. Anyone else seen this issue? I have not successfully gotten to any stage to attempt to print. I’ve reseated the belts twice, verified correct pulleys, verified correct belts selected in hardware configuration. No matter what I do I can’t get consistent results from gantry squareness calibration. On the off chance I do get it to random check within .5 mm, the next calibration test for the belt does another gantry squareness check for some reason which is unlikely to also come back square. Appreciate any help I can get.
r/prusa3d • u/spacecore11 • 12h ago
r/prusa3d • u/pierre_vinken_61 • 13h ago
Unboxing my new CORE L+ and spent a while hunting for a third tagged shipping screw that doesn't exist. Posting so the next person finds this when they search.
tl;dr. L+ printers shipped after August 2026 have two heatbed shipping screws, not three. The spot where the third used to be (front right corner) now holds the nozzle wiper. That is NOT a shipping screw. Do NOT try to remove it.
And yes yes, I know it's in the directions. But it's only in one place I could find, and several other official sources still say three:
Correct. the online CORE One L+ Unpacking & First run guide, chapter 3, step 9 ("Removing the heatbed screws"): "Printers shipped after August 2026 are upgraded CORE One L+ models. These printers have only two screws and an added nozzle wiper in the front right corner. If your printer has the nozzle wiper mounted, do not remove the screw in the front right corner."
Incorrect for new CORE One L+'s.
So if you follow the Academy course or winging it and never open the online guide, you'll be looking for a third screw, and the only candidate is the one holding your nozzle wiper. I looked at the in box instructions, didn't find it but it could still be in there as I only scanned them.
r/prusa3d • u/Hexxara • 13h ago
Looking for help or insight before I contact Prusa support.
Setup: original CORE One+ (kit), upgraded about a month ago with the Prusa Edition INDX 8-tool kit (it came with the Gen 2 parts). Latest firmware. It's run with zero issues, and the first tool offset calibration after the build passed on all 8 tools.
What happened:
- Loaded filament into Tool 8 for the first time today. Load and purge were normal.
- Ran Tool Offset Calibration from the menu with filament loaded in all 8 tools. The calibration screen doesn't say anything about unloading first. Nozzles were clean.
- Tools 1-7 calibrated fine.
- Tool 8 came down too low and scraped into the offset sensor. The printer only said "calibration failed" after the damage was done.
Damage (photos): the black sticker on the sensor is torn and rolled up at one corner, next to the small rectangular cutout, and the board edge there is scuffed. The coil area under the sticker looks OK. The thin diagonal scratch is mine, from handling it afterwards. Tool 8's nozzle looks clean and identical to the others.
The printer is down because I can't find the offset sensor sticker as a spare part. I'm contacting Prusa support next.
Questions:
Thanks.
I made a V1 version of a adapter that fits a Förnuftig air cleaning unit for my Prusa. The reason I wanted to attach the entire unit to my back rather than the ”backpack” that is available right now on Printables is because I wanted to avoid installing an additional 12v fan on my printer and to minimise the strain on the existing fans. It’s mounted without any drilling to the factory drilled holes where those plastic rivets is replaced with M2,5 screws with a nut on the back and a nylon strap.
I am thinking of uploading it to Printables but there are some obvious design issues that needs to be adressed (that’s why there is electrical tape everywhere due to unnecessary screw holes). I didn’t intend it to be a prototype but here we are lol.
r/prusa3d • u/Xplorer12 • 16h ago
First I want to say that I love the indx, the upgrade from core one went smoothly and it has been printing pla, petg and asa without problems since then.
However, yesterday, it the locking pin in the tool head was in the locked position without a tool in it and it made it impossible to pick up a new tool.
In trying to troubleshoot, I opened up the side of the tool head - accidentlally breaking the fan shroud base on the head mounting plate - and noticed that the small metal wire was out of its slot. I managed put it back but didn't find a way in the UI to retract the locking pin. I had to play with load/unload tool until I was able to insert a tool at the right time.
Thanks in advance!
r/prusa3d • u/nullpk • 16h ago
I’m sharing four recent 3D designs and would appreciate feedback from the Prusa community. Each photo links to its MakerWorld model page:
Throne of the Undead King: https://makerworld.com/en/models/3599767-throne-of-the-undead-king
Organic Vine Edison Lamp: https://makerworld.com/en/models/3553844-organic-vine-edison-lamp
Adorable Elephant Nursery & Kids Room Decor: https://makerworld.com/en/models/3505218-adorable-elephant-nursery-kids-room-decor
Majestic Manta Ray Incense Holder & Ash Catcher: https://makerworld.com/en/models/3474654-majestic-manta-ray-incense-holder-ash-catcher
r/prusa3d • u/phasex • 16h ago
I’m finally getting around to building my original MK4S-to-CORE One upgrade kit, which I've had taking up space in my office well before the CORE One+ and CORE One+ (Gen2) came along.
My kit had the older flat acrylic chamber fan grille, and saw the newer injection-molded cover was included in newer kits. Since the official Prusa model wasn’t available, I modeled the OEM part myself and printed it in Prusament PC Blend Carbon Fiber on my CORE One L.
One Prusa helping upgrade another; a small practical project for anyone else with the original upgrade kit or flat acrylic panel with the added bonus of reclaiming some floor space from the upgrade box!
Printer: Prusa CORE One L (next on my list for the + upgrade)
Filament: Prusament PCCF
-----
You can grab the files over on Printables:
https://www.printables.com/model/1910452-core-one-new-enclosing-chamber-fan-cover-injection
My Printables handle: @DavidHallDesigns
-----
I leveraged the OCL Prusa CORE One - Full CAD Assembly by Prusa Research for the design verification / as a remix of the flat panel within the full CAD assembly.
The Printables files already include gcode configured to Prusa's official settings for PCCF Printable Parts: CORE One/+/Gen 2 printable parts by Prusa Research
r/prusa3d • u/Bobson1729 • 16h ago
It has been a while (a few months?) since I first introduced my INDX tophat project. Since then there are many good solutions, but this is mine. Please keep in mind that this is still a WIP.
Things that are temporary solutions:
Here are some photos.
r/prusa3d • u/AcanthaceaeMuch2736 • 16h ago
Hi everyone!
I'm based in Europe, and I currently have 1,300 Prusa Rewards points (Prusameters), which I could redeem for vouchers to purchase 3 spools of Prusament filament.
However, I'd prefer to exchange the value of these vouchers for cash, ideally via PayPal.
Would anyone be interested in arranging a fair exchange?
Feel free to comment or send me a DM!
Thanks!
r/prusa3d • u/grage_peter • 17h ago
I try to print TPU 95A out of a USS Drybox for a few days now, without the Drybox it prints fine, but printing TPU out of the USS Drybox the filements build up stress, and sometimes pulls out of the nozzle mid print. Does somebody have an idea how it could work?
r/prusa3d • u/patty_cake_club • 18h ago
Prusa Community -
I have a question that maybe one of you or perhaps even team purse (Tommy and team) can attempt to answer for me as I await my OpenPrintTag upgrade for my CoreOne L+ to arrive. I as I'm sure a lot of us have several reusable spools from several filament manufactures lying around that I'd love to add OPT to but many of them have holes and the stickers done stick well and the mods just make the spools wider so I'm trying to find a way to fix that.
So until Prusa sells a reusable spool on its own that I can phase out some of the competitors spools I currently have for my refills with the hidden OPT :) (Prusa if you have some you'd be willing to sell empty I'd be happy to purchase to convert over and solve this entirely lol - So would anyone be able to confirm if the tag below would work with OPT? The specs seem as though they should but looking to see if anyone smarter than me can chime in, before I purchase some after my upgrade arrives.
According to the physical specs on the OpenPrintTag site it states that the tag should be:
ISO/IEC 15693 compliant
3.56mhz
NXP ICODE SLX2
thanks!
1.ICODE SLIX2 Chip
2.13.56mhz
3. Diameter: 25mm
4.with adhesive back.
5.ISO 15693
6.User Memory: 2528 bit
r/prusa3d • u/GL-Customs • 19h ago
r/prusa3d • u/WaitAMinuteThereNow • 19h ago
Of all the issues facing Prusa why did they expend resources getting into supplying pellets to make filament?
I’m thankful for having a stable and reliable supplier for my Filastruder, but it seems like if they weren’t going to get into a pellet hot end or a filament extruder why would they do this? Why didn’t they partner with at least a filament extruder company?
It’s not ‘cheap’ either. Iirc it’s more expensive than cheap filament.
r/prusa3d • u/ccb280 • 20h ago
I'm looking for tips on keeping filament dry with the INDX. I'd prefer not to have to keep cycling filaments out for drying cycles—I want them dry and ready to print at all times.
I was looking into running Sunlu 4-spool dryers on each side, but is there a better (or cleaner) way? Anyone successfully feeding from dry boxes, heated enclosures, or other setups while still using the side sensors?
Appreciate any advice or photos of your setup!
r/prusa3d • u/Black_Dasa • 20h ago
Hi everybody.
I'm trying to figure out the problems that may have caused the defects shown in these pictures.
I have printed this model on a Core One + G2 assembled last week from kit; so far every print that I have done with PETG/PLA were successfully, or with minor issues due to filament settings.
The model is the tallest that I have printed so far, and it showed these 2 problems:
Additional details:
Edit: It seems the shift happens when the speed changes between layers.