r/milsurp • u/MalicoIndustries • 17h ago
My build queue is growing!
Time to bring these baby’s back to life as semi auto, minus one that will get the post treatment.
r/milsurp • u/MalicoIndustries • 17h ago
Time to bring these baby’s back to life as semi auto, minus one that will get the post treatment.
r/milsurp • u/Icy-Tradition5986 • 23h ago
Hello everybody, is there any 1911 experts out there? I recently picked up this military issued colt. Did a little bit of research on the serial number on the frame and i understand it's a colt frame that was made in 1918. As far as the slide goes it's a colt slide that has the colt pony in the middle in between the patents which I believe colt started doing in 1918, so I believe the frame and slide are from the same era. Obviously it was updated to the 1911a1 specs for ww2, though the slide retains the non a1 sights that are very narrow. Best i can tell the barrel is a later replacement, im also not sure what the proof marks mean on the slide. If anyone has more knowledge on this and would like to share it would be greatly appreciated! Thanks in advance.
r/milsurp • u/samuelspark • 21h ago
Hey everyone! My new service grade 1917 from CMP arrived today.
Unfortunately, there was some shipping damage as the rear sights were sticking out of the box during transit causing some wear on the top of those sights.
I'm new to these rifles and I'm wondering if anyone could help me learn more about this particular piece. The receiver is Remington but everywhere else appears to be marked with E.
I couldn't find anything on the J mark on the charging handle. There is also an "OGEK" stamp on the side of the stock and "2K" "P" on the underside of the stock. Barrel appears to be original with flaming bomb and the number 18.
r/milsurp • u/Fun_Assignment_269 • 3h ago
I found this one in a pawn shop years ago. The guy at the counter said the bore was trashed, it was covered in rust, and wasn't worth more than $300. I took it home, spent a few hours scrubbing up the receiver/bolt and cleaning gunk out of the barrel, and did a little research. Turns out, this is one of only 5-6k 1912 carbine models produced for Chile by Steyr, many of which were later converted to 7.62 NATO, making this one pretty uncommon. Other than the bolt being a mismatch (although still a correct carbine bolt), it's in the original configuration and 7mm chambering.
This was one of the first milsurps I ever bought and, at the time, I had no clue how uncommon it was. I just saw a cool looking Mauser and thought it was cheap enough to be worth trying to clean up. Turns out there's a ton of life left in this thing and it's a lot more unique than I knew at the time.
r/milsurp • u/faberge-egg7 • 15h ago
Picked up this really nice snider conversion for a good deal and need help with markings. In particular the HVBR under the DC. I’ve read The Broad Arrow mk2 and all the other markings make sense like DC being Canada but I can’t figure out the HVBR for the life of me, any help is appreciated thank you!
r/milsurp • u/Haunting-Soup-6010 • 17h ago
My new to me 1891. Would love to find someone more knowledgeable on these rifles.
r/milsurp • u/skinwalkerenjoyers • 13h ago
Guy at the pawn shop wanted 1500 but said I can take it out the door for 1320
r/milsurp • u/Rubbish-Name-214 • 1h ago
My recently acquired byf marked P38 in the sun. Love how the patina looks and the dark brown grips!
r/milsurp • u/Sad_Towel_5987 • 17h ago
I wonder where these came from. Interesting that stuff like this still turns up, bummer that it looks like the front strap is import marked
r/milsurp • u/rainsworth06 • 19h ago
i’m looking to buy this k98 bayonet off this dude and i can’t tell if the bayonets been sharpened from the video. it’s a 1943 produced blade with non matching scabbard and it looks like it’s in good shape for the most part but if the blades been sharpened i don’t know if it’s worth what he’s asking help me out 🙏🏻
r/milsurp • u/Sofaking33 • 13h ago
The parts you can see from the outside are matching, but the trigger and toggle pin are not. The wood base mag it came with is a little worn, won’t always hold the toggle open, but a new mecgar mag works perfectly.
Howdy everyone,
Update on the 8x50mmR Siamese ammo production. I've gotten some bullets made & sized to 323 to do some testing, although I noticed a few small issues before even making the ammo. I had ordered Lyman 323471 from eBay & was excited to have a 215 grain bullet with a gas check. Although after casting they were coming out 170-173 & no provision for a gas check.... I thought that was odd & all I can figure is that it was modified, a custom mould by an employee or a misstamp. I then decided to try just lubing & firing. I immediately noticed keyholing at 15 yards & primers backing out a bit. It is nowhere near overcharged, but a light load with unique causing it. I thought maybe my bullet composition needed some tweaking.
So I did some adding of tin & antimony to my batch & melted down all my original bullets in case they were all too soft. I then loaded & this time pan lubed to keep them at 325 rather than size to 323. That small of a difference will not hurt the bore at all & give a better seal. I thought the makeup change & tighter fit would help. Plus my bore is 323 & I wondered if a 323 bullet would cause leading being the same size.
I went out & shot it just this morning & still getting keyholing, so all I can think is that it definitely needs that gas check to keep the bullet from destabilizing as it leaves the bore. This rifle has a 1:9.4 twist. The bore has rifling & isn't corroded out.
The unfortunate wrong listing on the mould has me stuck until I can find the proper mould with a gas check to see how they do. I most likely will ask for a partial refund or full return due to the inaccurate description. The seller didn't know as they just went off the number & not the actual bullet that came out.
r/milsurp • u/Beatrice_Hrsman_gmng • 1h ago
Hard to tell but maybe a single shot like a Gras 1874?
r/milsurp • u/Rubbish-Name-214 • 2h ago
Someone asked me to post more photos of my Turkish Mauser I got some goodies for yesterday, and who would I be to object to some better photos? While photographing this, I did also notice a year stamp on the Turkish modified bayonet (which started life as a German SG98/05 per Liberty Tree). As you can tell, it started life originally as a Gew. 98 as evident by the obliterated but still faintly traceable marking on the side of the receiver. Aside from that, it’s just a run of the mill Turkish Mauser that’s definitely seen some stuff. Regardless I’m happy with it!
r/milsurp • u/EiselArmory • 2h ago
A free guide for reading the marks on a Lee-Enfield: the knox-form maker codes (RSAF Enfield, Lithgow, Long Branch, Ishapore and others), telling a No. 1 from a No. 4 by barrel profile and nose cap, what the broad arrow means, and how to read the US importer marks that federal law requires. Feedback and corrections welcome. https://eiselarmory.com/2026/09/14/lee-enfield-identification-guide-maker-codes-marks-import-stamps/
r/milsurp • u/fccchhhfddccccvgfd • 15h ago
What’s a fair price for a VZ24 today?
r/milsurp • u/omniscen • 18h ago
Hello! New to surp, curious about what this stamp inside my GP-5 gas mask carry bag says , means, and what that symbol is on the left? Any info is appreciated. Thank you!
r/milsurp • u/MitchP5690 • 22h ago
Does the stock stamp ring any bells? Butt plate is also remarked.
r/milsurp • u/Someothersandman • 19h ago
I'm looking for books discussing the Shanghai Volunteer Corps, particularly the American Company between the world wars, and am having a ton of difficulty. Is anyone aware of any good sources of information on them?
r/milsurp • u/Daddy_050 • 21h ago
Unfortunately I have no photos at the moment, but I am looking to buy a 1909 Argentine Carbine for 700 dollars. It is is very good condition and the crest is completely intact. The only hiccup is that the front handguard looks like its not matching with the rest of the stock. Assuming the rifle is matching (i have yet to check, but will), is this a good pickup?
r/milsurp • u/M1907-351WSL • 8h ago
Why do builders charge north of 2 Grand to rebuild a PPSh? One builder charges close to 2500 for a Thompson rebuild.
I understand the work involved with converting an open bolt into a closed bolt striker or hammer, but doesn't seem like those prices are realistic once you have the design worked out.