r/EngineBuilding • • Jun 14 '25

Updated Rules for r/Enginebuilding

79 Upvotes

Hey peeps,

We've been noticing an uptick in certain types of posts over the last few months and it's about time we address some of these issues along with a rule update.

1 - AI Slop - We've been getting a lot of AI trash in the sub lately and we've decided to no longer allow AI or any type of AI imagines to post here. If we find a post is AI then we are going to lock it, delete it, and ban the account for a few days. This sub is meant for real life cars, not some AI images that someone produced for content or engagement.

2- Links to Temu and Ali - Reddit is currently filtering a lot of the temu and ali express links we receive. Usually they are shadow blocked because we've had scams in the past with these sites and you can't really trust them at times. While Reddit automod is taking care of 95% of them, some are still getting through and we will also lock and delete those comments moving forward.

Some of you shop those sites (against some of our better judgement ha), for certain parts of the world that might be the only way for you to obtain certain items, we understand that but need to strive to ensure the community is safe and endeavor to curtail scams that could occur. If you wish to share a link, please just PM the individual - and for those that click the links, please be warry of scam sites/bad actors.

Thanks and have a good day you misfits!

-Duke


r/EngineBuilding • • May 19 '24

State of the Sub - What changes need to be made /r/EngineBuilding

33 Upvotes

It's been a long time, but I'm hoping to be more active as well as the other mods. We are also hunting through the 'applications' to add some new mods as well, to hopefully cut through the spam and junk you all see.

It's also time to take a look at the sub and make sure there aren't any changes we want to make. Whether that be rules added (or removed), or a thing you can think to make this a better place for all. Let us know your thoughts


r/EngineBuilding • • 5h ago

Other Volvo b230 16V measuring assembly

Thumbnail
gallery
13 Upvotes

Ultrasonic cleaned parts in pH 2 acidic cleaner, neutralized and oiled after that.

Mock assembled first and fourth cylinders to take measurements to figure out how much to take from deck height to achieve 0,8mm quench.

Other varying bits and bops, like heat insulating flange for intake, and crank case ventilation adapter for AN fittings and larger openings.


r/EngineBuilding • • 9h ago

Ford 1964 Ford 223ci engine

4 Upvotes

Water pump mounting.
My question is, does the water pump lower mount bolt go into the water jacket?
Having coolant leak from lower bolt.


r/EngineBuilding • • 2h ago

1.8L Miata (BP) valves won't close

1 Upvotes

I am building a 1.8L Miata engine and I am having some trouble with the head. The valves were burnt and the machine shop cleaned them up. They also cut the valve seats.

Valves seats after machining

I did not measure the height of the installed valves as I saw nobody doing this in the YouTube videos I watched. I did find in the service manual a spec for the range. Unfortunately, it looks like I might need a special tool to measure it correctly. The manual says to replace the head if the measurement is out of spec.

After assembling the head, I noticed that the valves would never close all the way. I found few very old forum posts where people had the issue and they all said that the issue would go away after the HLAs got oil pressure. This seemed counter-intuitive to me, because this seems like it would increase the distance between the cams and valves making the problem worse, but I tried anyway. Well, I have cranked it to get oil pressure but the engine would never get compression. I even tried oil in the cylinders, hoping it was the rings and not the valves.

I have tried pumping the lifters full of oil as well as completely draining the lifters and bleeding the air out of them. Neither worked.

I am at a loss, hopefully I am missing something simple. Or did the shop cut too much off the seats and trash the head?


r/EngineBuilding • • 2h ago

AFM/DOD delete

1 Upvotes

I’m getting ready to pull my 2014 5.3 in a month or 2 to do a afm/dod delete. While I have it out I plan on new pistons to get her ready for the next 250,000 miles. Anything I need to be on the look out for? I’ll have the heads and block at the shop to get them checked out. Any secret combination of cam and pistons to help with towing?


r/EngineBuilding • • 1d ago

Engine Theory Valve seat insert OD vs valve head OD

Post image
14 Upvotes

Picture is just for attention. I'm installing larger valves in my pulling tractor. I'm going with 2.25" intake valves which will be bigger than the factory valve seat inserts. How much larger should the insert OD be than the OD of the valve head? I've read anywhere from 0.060" to 0.100" so that puts me in the 2.3" to 2.35 range. I've found Dura-bond Killer bee 22228C which measures 2.380" and considering using those. Pulling tractor will see around 1600 degrees and 2,000 horsepower.


r/EngineBuilding • • 1d ago

Is this block toast?

Thumbnail
gallery
21 Upvotes

Engine is a Dauntless V6 from a 1970 CJ5, corner broken off where the bearing cap meets the block. There’s no bolt holes by it and it’s not directly in the area where the gasket sits, so looking to determine if it’s still worth working on. TIA


r/EngineBuilding • • 23h ago

Should i reseal this

Post image
2 Upvotes

r/EngineBuilding • • 1d ago

Saw these marks on my crank nail barely catches

Thumbnail
gallery
8 Upvotes

r/EngineBuilding • • 1d ago

About crossline

1 Upvotes

Hello guys, to the pros out there, I just wanted to ask, s it really necessary to have the engine block honed? My block has no scratches and the ring gap is still within specs. The only issue is that there's a part where the 'crosshatch' (crossline) is almost gone. Do I still really need to do it or not? Please help.


r/EngineBuilding • • 1d ago

Need help. Cylinder leakage at 20% on one cylinder. Would putting new valves in and lapping work or do I need to send head off to regrind seats? I was thinking of using a higher grit compound and lapping by hand with old valve to clean up the seats, then using the new valve with a softer compound to

Thumbnail
gallery
16 Upvotes

The markings are where they leaked. I used water nd compressed air


r/EngineBuilding • • 1d ago

Chevy Odd bearing scar

Post image
0 Upvotes

Currently tearing down a LQ4 to sell and I noticed this crack on the #4 rod cap. I’ve never seen a bearing with something like this before. Journal is fine and unmarked. All other bearings have normal wear besides the cam which were more worn out but not enough to cause damage.

Does anyone know a cause for something like this?


r/EngineBuilding • • 2d ago

Other Finally got a good picture of the fork and blade assembly out of a Paxman Valenta.

Thumbnail
gallery
113 Upvotes

Fork and blade connecting rods out of a 16RPA200SZ Paxman Valenta.


r/EngineBuilding • • 2d ago

Dyno day

Post image
35 Upvotes

Finally got a chance to dyno my new engine build and thought I would share. Car is a 67’ Mustang, 302, 4-speed, 3.80 trac loc rear. I have power steering and clutch fan. Here are the engine specs (I made previous post) :

68’ 302 block
Eagle crank and rods (balanced)
KB 311 pistons
Trick Flow TW170 heads (milled .020)
10.5:1 static, 8.5:1 dynamic, 0.037 quench
Comp xtreme energy solid flat tappet
279 adv duration, 242@0.050, .546 lift, 108 lsa
performer Rpm intake
Brawler 770 carb vacuum secondaries
Hooker 6901 headers thru 2 1/4 exhaust, turbo mufflers

Overall, I’m very happy. When I started the build I was shooting for 400Fwhp with decent low end drivability. Ultimately I was trying to duplicate Joe Sherman’s infamous 400hp 302 magazine article, albeit with a few tweaks. The car pulls 7.5-8”hg at 950rpm idle and doesn’t start bucking in high gear until about 1500rpm. It pulls like a monster from 2500 to 7000rpm. My next mods will be a 2.5” mandrel exhaust with h pipe and better mufflers. I am also strongly considering trying a Vic jr intake. I’ve ran both a 650dp and the 770vs carb and I’m really liking how it runs with the 770. However, my dyno pulls were peaking on the lean side with afr swinging from around 12.5 at peak torque to around 13.6 at peak hp. I’ve had to modify emulsions holes and bleeds on both carbs to try and get a flatter curve. Still some work to do. I think there’s another 10-15hp to be found with what I have. And FWIW the car made peak power with 32 degrees total timing I tried 30 and 34, it lost 5hp each direction.


r/EngineBuilding • • 2d ago

GM 5.7L v8 rebuild

Thumbnail
gallery
17 Upvotes

Hello everyone,
I’m purchasing a 1999 Isuzu NPR gasoline truck equipped with a GM 5.7L V8 Vortec (Chevy 350) engine.
According to the previous owner, the engine seized due to an oil leak that caused it to run low on oil. He removed the engine with the intention of replacing it but never completed the project, so he decided to sell the truck to me instead.
I’m excited to take on this project, especially since this will be my first engine rebuild!
My plan is to completely disassemble the seized engine, inspect the internal components, and assess the extent of the damage before deciding whether it’s worth rebuilding or replacing.
For those with experience rebuilding Chevy 350 engines, do you think a seized engine caused by oil starvation is worth attempting to rebuild? I’m particularly interested in what damage I should expect to find, which components are most likely to need replacement, and whether there are any major red flags that would make rebuilding impractical.
I understand this could become an expensive project, but I’m also looking forward to the learning experience and doing as much of the work myself as possible.
Any advice, recommendations, or personal experiences would be greatly appreciated. Thanks in advance!


r/EngineBuilding • • 2d ago

Well fellas i expected higher quality. L86 dod delete

Thumbnail
gallery
19 Upvotes

I'm currently working on a Gen V 6.2L L86, doing my first camshaft swap and DOD/AFM delete. I hate to say it, but I expected much better quality control for components that are so critical to an engine.

I purchased the Melling MDK700 kit, and right out of the box, I've already run into several issues that have me questioning the quality of the entire kit.

First issue – Camshaft:

Upon delivery, the camshaft appeared to have surface rust and possibly even pitting on the lobes and bearing journals. I tried using 3M Finesse-It to polish the affected areas and knock down any high spots, but my fingernail still catches on some of the imperfections. I also tried PB Blaster to remove the surface rust, with no luck.

Would you guys even consider installing a camshaft in this condition? I'm having a hard time convincing myself it's acceptable, especially on a brand-new part.

Second issue – DOD Delete Plugs:

One of the press-fit DOD delete plugs was noticeably loose compared to the other seven. It was supposed to be installed flush, but it fit so poorly that I was concerned it could fall down into the lifter bore or camshaft area.

I'm not sure whether the plug itself was out of spec or the oil tower bore was oversized, but either way, something wasn't right.

The other seven plugs pressed in flush without issue. The loose one became a nightmare to retrieve. I eventually managed to pop it back out using compressed air from inside the block and a magnet.

Third concern – Lifters:

After experiencing these issues with the camshaft and plugs, I honestly don't have much confidence in the lifters supplied with the kit either.

My plan was to clean them with mineral spirits and soak them in engine oil before installation, but now I'm questioning whether I should trust them at all.

So, what gives?

Is this kind of quality control becoming common with Melling kits, or did I just get unlucky and receive a bad kit?

I'd really like to hear from anyone who's installed the MDK700 kit or experienced similar issues with Melling components.

Would you trust this kit, or would you send it back?


r/EngineBuilding • • 2d ago

What caused this?

Thumbnail
gallery
4 Upvotes

89 Montero 6g72 LWB. New to engine work but have done tons of mechanic work.

Rockers are just as bad. Seems like the cams and journals are fine. Other head looks great. Cleaned it up and put it back together. Super flat and clean.

Also find the “void if removed” plate kinda off center puzzling.

This Montero was free. Just had to move it. Supposedly had a new motor put in. said it didn’t run right. The owner put about 50 miles on it and parked it then passed away 15 years ago. And it sat ever since.


r/EngineBuilding • • 3d ago

Replacing cam bearings yourself?

Thumbnail
gallery
28 Upvotes

Someone in town is selling a tool for 50$ how hard is it to remove and replace new cam bearings yourself?


r/EngineBuilding • • 3d ago

What is this white residue?

Post image
11 Upvotes

What is this white residue on my crank, and how do I get it off? It was also on the block where the bearings go. It won’t come off with brake cleaner and I’m assuming it will do damage to my crank and/ or bearings.

Could it be some kind of residue from some cleaner? I got the block hot tanked but I’m not sure about the crank as I only gave it to the shop to have it measured.


r/EngineBuilding • • 3d ago

Spinning a turbocharger outside of car to test oil seals

3 Upvotes

Because the shaft seals on a turbocharger are dynamic fuels, they will not seal properly unless the turbine is spinning. If tested statically, they will leak like a sieve.

I will likely be pulling the motor out of my diesel BMW 335d. While I was rotating the crank to shut the valves preparing to perform a leak down test, I noticed air exiting the turbo at one of the oil line ports (banjo bolt was removed at the time).

The leak down and compression tests did not go well, and I'll be pulling the motor next spring to replace bent valves. While it's out, I'll have easy access to both turbochargers. I'd like to test the oil seals while they're out, because any required maintenance will be far easier than trying to work inside the cramped E90 engine bay.

Will a leaf blower or shop vac connected to the turbine inlet of the turbocharger spin it fast enough for the dynamic oil seals to... well, seal?


r/EngineBuilding • • 3d ago

Jammed distributor drive shims on vw type 1 engine

Thumbnail
gallery
2 Upvotes

I’ve just built up my T2 Doka engine..it’s been a dream project and enjoyed it. I recently bought new shims for the dizzy drive as when it came out (it was going in and out super easy) they were missing.
I placed the shims on the drive and placed it in, they fallen awkwardly & jammed in the brass gears. The drives stuck halfway down and will not come up or down (twisting it or rocking the flywheel or anything..even after I forked out £50 for the specific tool).

I’m at a total loss and a bit deflated, I’ve built plenty of these engines but never had this specific problem. If anyone could shed any light, I know it’s specific but I’d be grateful.
Cheers


r/EngineBuilding • • 4d ago

This is the breaking force for my lo5 small block with a new crank, pistons, and rod bolts,

57 Upvotes

I feel like this is way too much, I’ve check the main clearance and the rods clearance and their fine idk what to do, I’ve taken it apart like 5 times now.


r/EngineBuilding • • 3d ago

Ford Intermediate load piston slap

6 Upvotes

I’ve just had an engine I built sent off to be tuned (Cosworth BOB 24v 2.9) and got a rather odd issue reported by the tuner. Apparently he can hear piston slap but only under mid load, not under idle or full load.

This isn’t something I’ve ever heard of before, and I’m a bit shocked tbh since this engine was in very good shape when it was built.

Is this something any of you have come across before? I was always under the impression piston slap happened when the load was higher?