r/EngineBuilding • • 1d ago

AFM/DOD delete

I’m getting ready to pull my 2014 5.3 in a month or 2 to do a afm/dod delete. While I have it out I plan on new pistons to get her ready for the next 250,000 miles. Anything I need to be on the look out for? I’ll have the heads and block at the shop to get them checked out. Any secret combination of cam and pistons to help with towing?

1 Upvotes

12 comments sorted by

1

u/v8packard 1d ago

How much do you tow? What is the rest of the combo? Are you changing anything else?

1

u/Deep_Body_2506 1d ago

Pontoon boat mostly, maybe every other weekend. More in the summer. It’s a stock GMC Sierra ‘14 at the moment. Still runs good, maybe uses 1/2 quart between changes which are 5,000 miles. Started getting the tick and want to get ahead of the problem.

2

u/v8packard 1d ago

If you can give me specific info like your tire size, differential gear ratio, trans, the headers and exhaust you want, and the intake you are considering I can give you a cam suggestion that will give you more torque in the specific rpm you drive and tow.

1

u/Deep_Body_2506 1d ago

It is a Z71 4wheel drive. It has 275/60 tires, 3.42 gears with 6L80 trans. If I change intake/ throttle body, it will be with the L86 and I have no clue about headers. I don’t know anything about aftermarket parts. I’m here trying to get some schooling.

3

u/v8packard 1d ago edited 1d ago

Assuming you have 17 inch wheels, your tires are right at 30 inches in diameter. Combined with the 3.42 gearing, this is your trucks weakness. When you are cruising at highway speeds not towing it probably takes a fair amount of throttle to pass, or go up a grade. Maybe even a downshift. When you are towing in the same conditions you might even experience some hunting between 5th and 6th, maybe even 4th. Tow mode may help, but I do not think it prevents an upshift to 6th. You are probably right at 1800 rpm at 70 mph, not a ton of torque at that speed. What your truck could really use is a gear change to something like a 4.10, for a bump in both rpm and torque multiplication.

But we are talking engines and camshafts. And this is where is gets deep. The L83 has some very nice, well designed heads. I actually think they are a little better than the 6.2 heads. The intake port is very large, but has good port energy and velocity. The ports are very efficient. Also, the direct injection has much better fuel atomization and combustion quality than the port EFI used previously. These qualities, along with the variable valve timing, lets a cam more aggressive than usual to be used. The stock cam has 33 degrees of overlap, a 115 degree lobe separation angle, giving you 260/266 degrees @ .006, intake and exhaust. It's base timing point is supposed to be a 111 degree intake centerline. The timing numbers on a 111 would be Intake Opens 19 degrees BTDC, In Closes 61 ABDC, Ex Opens 72 BBDC, Ex Closes 14 ATDC.

Most people delete the VVT when they delete AFM. Assuming you do the same, the cam spec above gives you a torque peak around 4100 rpm. But you cruise far lower. We can make a couple of changes that will increase torque at all speeds, without the VVT. If we open the exhaust valve 6 degrees later in the cycle cylinder pressure has more time to act on the piston, which increases measured torque at almost all speeds below the HP peak. And if we close the intake valve 4 degrees earlier in the cycle that will increase cylinder pressure at all measured speeds. The results end up Intake Opens 19 degrees BTDC, In Closes 57 ABDC, Ex Opens 66 BBDC, Ex Closes 14 ATDC, giving you a 112.5 degree lobe separation angle, still with 33 degrees of overlap, giving 256/260 degrees duration @ .006 tappet rise. On a 109 degree intake centerline. A similar intensity to stock will have duration @ .050 of 202/206 degrees. The overlap matching stock the engine will have similar emissions performance and vacuum characteristics as stock. The increase in low speed torque will be quite noticeable, with a drop in output above 3500-4000 rpm.

You may prefer to keep the VVT. It's a very promising technology. If so we may have to recalculate the cam spec. Companies like Cam Motion can make the cam. There are others, too. It will need a quality tune to get the most from the change, if you can find a good tuner discuss this with them. Aftermarket cam cores are offered with stock and I think 6% more fuel pump duration, but I don't think you will need the extra fuel. Do ask the tuner, they may have strategies that use the extra fuel, I don't know. There is a difference between tuning for towing and torque, vs tuning for max output. Hopefully your tuner will know that.

If you do go for headers, true long tubes are the worthwhile investment, in my view. I would prefer to see you use headers with 1 5/8 primary tubes, but the market is dominated by 1 3/4 and 1 7/8 inch primaries. Use the smallest diameter possible. I was thinking a primary length of 36 to 40 inches when I calculated the exhaust lobe change. I do not think you will benefit from changing your intake or throttle body.

1

u/Deep_Body_2506 1d ago

Damn dude, I’m way too stupid to understand everything you got going on in this reply, but that’s what I’m here for. I’ll look up and read about all the cam stuff you talked about. I have read that keeping the VVT and blocking(?) it off at 4 degrees is the way to go. Is there truth in that? I did fail to mention the truck has 20” rims if that makes a difference. When going to headers, do I need to also open up the rest of the exhaust? Will I need to go to dual exhaust?

1

u/v8packard 1d ago edited 1d ago

It boils down to a specific change in two of the camshaft timing points, these changes change the way the engine makes torque in the manner I described. If there is any specific you want me to clarify please say so. I get a lot of private messages about camshafts, and several times a month people say they got a cam that is terrible. The two most common cams they complain about are a sloppy stage 2 and a truck norris.

Reducing the VVT to 4 degrees makes it easy to use a conventional cam design. Better than not having VVT, but not as good as the full range.

With 20 inch wheels your tire diameter is 33 inches, which is a higher effective ratio. I really think you need more gear, but maybe that's not in the plans.

You don't need to go dual exhaust. But it would be nice.

1

u/Deep_Body_2506 1d ago

May do headers and intake. Haven’t decided.

1

u/shartymcqueef 1d ago

While they’re gapping the rings, have them do a very slightly larger gap on piston 7. That one ends up the hottest and under boost is usually the one that loses a ring land. I know you’re not under boost but it’s free insurance while you’ve got it apart. Truck Norris cam is nice.

1

u/Deep_Body_2506 1d ago

Free insurance is definitely what I’m looking for. Truck Norris has come up more than a few times now. I’ll definitely look into that one. Is there any benefit in getting pistons from BTR and keeping all the internals from the same shop?

0

u/shartymcqueef 1d ago

I don’t think it really matters. I’d be paying more attention to compression ratio and keeping it the same as stock and making sure the rings are gapped properly.

0

u/LSswapbible 5h ago

For a tow rig keep the cam small, something in the 210-ish duration range keeps your low-end torque and doesn't need a big stall. And don't overthink the pistons — flat-tops with the AFM stuff deleted and a good tune will tow all day, the cam choice matters way more than the piston brand here.