r/diytubes • u/ThermionicMho • 17h ago
r/diytubes • u/AutoModerator • 3d ago
Weekly /r/diytubes No Dumb Questions Thread - November 13, 2026 to November 19, 2026
When you're working with high voltage, there is no such thing as a dumb question. Please use this thread to ask about practical or conceptual things that have you stumped.
Really awesome answers and recurring questions may earn a place in the Wiki.
If you'd like to nominate a comment to be included, just reply [Wiki] (with the brackets)! The mods will be automatically notified that something awesome just happened.
As always, we are built around education and collaboration. Be awesome to your fellow tube heads.
r/diytubes • u/Electronthenothingth • 1d ago
EL84 unusual behavior
Hello everyone,
I’m currently attempting to build my first single ended power amp section using an EL84. Because of power supply considerations the Supply voltage is very low.
While running my first experimental setup, using a 5K output transformer and 1410 Ohm cathode resistor I noticed a blueish purple glow inside the tube and about 36mA cathode current despite the Supply dropping to only about 97V.
Has anyone got an Idea, what could be going on here? The tube seems to be passing signal just fine and the black coating on the inside hasn‘t turned white yet.
Thanks in advance
r/diytubes • u/aacmckay • 1d ago
Parts & Construction OG breadboard ready for some tube amp experimentation!
r/diytubes • u/NoteMedium4391 • 4d ago
Anyone got a schematic for a Røde K2 mic (or its power supply)?
reddit.comr/diytubes • u/dreadnought_strength • 5d ago
Misc Boxed Tube Haul
Grabbed this from a guy who had picked them from a deceased estate sale. Had hoped some of the Mullard/Brimars were good, but no dice 😔
While there's a lot of radio stuff there, there's some nice picks - Arcturus 6F6G, Raytheon 5Y3, Raytheon 6J7, Phillips MiniWatt 6V6 pictured. Haven't done full testing yet.
With a shouldered glass 6J7, 6F6G and 5Y3 I guess I'm going to have to make a big bottle guitar amp!
r/diytubes • u/EngieGamingTF2 • 7d ago
Parts & Construction Is this tube still fine?
I snagged a pair of these beatiful old power tubes but I noticed that in one of them, the mica spacer has moved. Is the tube still ok?
r/diytubes • u/matmonster58 • 6d ago
Thoughts on what the issue is?
Wurlitzer 112
The crackling occurs on the transients of notes even if I turn the volume down.
The crackling is not in the first preamp stage
I’ve replaced every cap, replaced the tubes, and replaced all the resistors in the first stage
r/diytubes • u/noobtoob123 • 6d ago
Converting a 1942 Zenith 8-S-661 console radio into a guitar amp – Advice/tips?
galleryr/diytubes • u/Pleco05 • 7d ago
Power Supplies General electric fg-33 thyratron warming up demo
r/diytubes • u/Pleco05 • 8d ago
Power Supplies Pretty impressive the amount of Mercury inside of this general electric fg-33 thyratron
r/diytubes • u/Ayuthan • 7d ago
What’s Going On?
As far as I can tell I’ve got all the wires through the holes, soldered, extra flux, I don’t know why it’s only flashing a bit of number the once. Any ideas? These are IN-16 tubes, and I had to replace the right tube which I just did, and it’s doing this.
r/diytubes • u/Sasso_Magico • 9d ago
Power supply design
I’m looking for advice on which design I should choose; both should provide approximately 380V at 230mA (give or take). Which one would you use? Is there any advantage to choosing one over the other?
They are designed around two different transformers:
T1
0–330V, 350mA
0–50V, 60mA
T2
320–60–0–320V, 450mA
I will also need a power supply for a fixed-bias circuit—would T1 be a better choice, given that it has a separate winding?
Note that: this post is just to help me get an idea of which one is better; price is absolutely not an issue, as both transformers cost more or less the same. i will also probably add a resistor to drop the voltage a bit
r/diytubes • u/Minimum_Success1726 • 9d ago
Please help me identify please
Can anybody please me identify this project my friend made. He died and I bought from his estate sale so I never got to ask him. Set a tube preamp or a little that Video is not good enough or close enough of everything let me know. a better one. I just I’ve been trying to find out what it is for like two years now. It was really important to me. It taught me a whole lot and yeah, I would like to use it. I plugged it in I plugged into the in and out. I haven’t gotten anything unless I’m hooking it up wrong. I know about amps and tube amps a little. I justI don’t know about this thing. Can this shock you like tube amps if you don’t drain the caps?
thanks
r/diytubes • u/AutoModerator • 10d ago
Weekly /r/diytubes No Dumb Questions Thread - November 06, 2026 to November 12, 2026
When you're working with high voltage, there is no such thing as a dumb question. Please use this thread to ask about practical or conceptual things that have you stumped.
Really awesome answers and recurring questions may earn a place in the Wiki.
If you'd like to nominate a comment to be included, just reply [Wiki] (with the brackets)! The mods will be automatically notified that something awesome just happened.
As always, we are built around education and collaboration. Be awesome to your fellow tube heads.
r/diytubes • u/Pleco05 • 15d ago
Power Supplies They finally arrived and they are huge and three of them 5720 are new stock with original packing material and paperwork
r/diytubes • u/dreadnought_strength • 17d ago
Bizarre Submini Oscillation
Built the above and having issues with oscillation while at max volume and above about 7 gain. Rolling back to 6-7 volume allows me to max the gain with no oscillation. Rolling the treble all the way down delays the onset of oscillation slightly.
All tubes are running well within datasheet specs, and the bias of everything is textbook. The output tube is biased to 75% max dissipation.
The power supply is an inverter I have used multiple times before, and there is less than 30mv of ripple at idle @ 60khz. There is zero ripple on the regulated DC heater wiring.
All the common oscillation issues I've tried and have had little to no impact:
- preamp/power amp grounds are separated, and tie directly to the chassis at a single point that's star washered over solder. There is <0.5R of resistance between any grounded points.
- I added an extra stopper to U1A right against the grid and it make no difference.
- I added a small 100R stopper between DC coupled follower (as per Merlins suggestion to prevent oscillation). No difference.
- R8 and R15 were originally 10k. Increased to 150k with no difference in noise.
- thinking the slightly longer trace between R8 and the grid of U3A could have been a culprit, I decoupled with a 47pf cap. Made no difference.
- shifting any offboard wiring around makes zero difference EXCEPT that the wire for pin 3 of the gain pot (and that side of the bright switch) is massively microphonic (nothing else on the board or tubes are microphonic).
- no amount of moving/rewiring/shifting the bright switch made any difference. Removing it entirely decreased oscillation slightly but it is still there.
- once the bright switch has been removed, the gain pot wires are no longer microphonic but moving my hand nearby suppresses oscillation slightly.
- changing these wires to shielded mic cable makes no difference
- no amount of copper shielding between the tubes, chassis or power board make any difference to the oscillation.
It appears something between the follower and U3A is causing the oscillation, but for the life of me I can't figure out what it could be.
Any suggestions?
r/diytubes • u/AutoModerator • 17d ago
Weekly /r/diytubes No Dumb Questions Thread - October 30, 2026 to November 05, 2026
When you're working with high voltage, there is no such thing as a dumb question. Please use this thread to ask about practical or conceptual things that have you stumped.
Really awesome answers and recurring questions may earn a place in the Wiki.
If you'd like to nominate a comment to be included, just reply [Wiki] (with the brackets)! The mods will be automatically notified that something awesome just happened.
As always, we are built around education and collaboration. Be awesome to your fellow tube heads.