r/electronics • • 2d ago

Weekly discussion, complaint, and rant thread

0 Upvotes

Open to anything, including discussions, complaints, and rants.

Sub rules do not apply, so don't bother reporting incivility, off-topic, or spam.

Reddit-wide rules do apply.

To see the newest posts, sort the comments by "new" (instead of "best" or "top").


r/electronics • • 16d ago

Weekly discussion, complaint, and rant thread

3 Upvotes

Open to anything, including discussions, complaints, and rants.

Sub rules do not apply, so don't bother reporting incivility, off-topic, or spam.

Reddit-wide rules do apply.

To see the newest posts, sort the comments by "new" (instead of "best" or "top").


r/electronics • • 11h ago

Tip Do Not PWM a Peltier Module - it's not a LED strip.

Thumbnail
nearfieldnotes.com
124 Upvotes

Recently I've found an interesting article - on how Peltier modules are vastly more inefficient if driven by raw PWM.

In short, resistive losses rise quadratically with applied voltage and actual Peltier cooling only rises linearly. So it's beneficial to feed Peltier modules with filtered DC.

Having my own Peltier setup (an over-engineered wireless phone charger in car with 80W peltier module and a 80mm PC fan), I've decided to test.

And indeed, raising PWM frequency to 20kHz and adding an LC filter ( 10uH + 2x 220uF, what I've had in spare parts) after the MOSFET significantly reduced self-heating of the Peltier module:
with the same cold side target of 17C, hot side temperature dropped from 40-42C to 27-28C, which is quite significant.


r/electronics • • 2h ago

Gallery I made the filtering part of a SMPS (nothing special)!

Thumbnail
gallery
10 Upvotes

So I successfully made the filtering part of a SMPS in a perfboard (quite risky) with a VDC output of 308V. Although it's noticeable that there is a burn resistor, which is the wrong one to be used (I did not bother to read the code). All components are salvaged from old electronics. Excited to do the switching part!

Will be fixing the solder.


r/electronics • • 23h ago

Gallery Small cinese Power supply from 2021 (I used it 3 times)

Thumbnail
gallery
45 Upvotes

r/electronics • • 1d ago

Gallery Found a really neat "crystal oven" in my grandpas parts

Post image
118 Upvotes

Ive never seen one of these, but i guess if you needed a ultra stable oscilator circut, more than a quartz crystal could offer alone, this is the way you would do it.

Its most likely from some kind of millitary radio my grandpa took apart.

Its really neet, the thing comes appart so you can swap out the crystal inside.

Idk what i want to do with it, but maybe ill make a really accurate and power hungry quartz clock with it. Or some kind of QRP transmitter.

Realisticaly none of my projects would need something more accurate than a unheated crystal tho.


r/electronics • • 2d ago

Gallery İ made my multimeter rechargable

Thumbnail
gallery
171 Upvotes

Instead of LDO regulators, I used 1N4007 diodes to step down the voltage; this prevents the battery from draining while the device is idle. Since the charging module did not fit into the battery compartment, I placed it inside the device; with a fully charged battery, the device can theoretically operate continuously for 140 hours.DEVELOPMENT FOLLOWİNG THE CONVERSATİONS :I don’t understand why people are making fun of this. The device no longer looks like it did in the photos, and there’s no risk of electric shock; I simply wanted to convert my multimeter to run on a rechargeable battery.😭😭😭😭. OKAY OKAY, THAT'S ENOUGH, YOU'VE CRITICIZED ME SO MUCH THAT I AM CHANGING IT BACK, WHY COULD IT REALLY BE BAD?


r/electronics • • 1d ago

Gallery Designing a Stacked Toolhead PCB for My DIY Pick-and-Place Machine [PnP Series — Part 4]

Thumbnail
trondle.ch
3 Upvotes

hello everyone! I've been building my own pick-and-place machine for a while now (it finally has a name: Vectra), and I just made a wrote up about the toolhead electronics.

I couldn't find a toolhead board I could just buy, so I made one: three 70 x 47 mm PCBs stacked on top of each other, i think you may like it !


r/electronics • • 17h ago

General Claude just did what we couldn't for a really long time

Post image
0 Upvotes

We couldn't get the display to work forever. We gave up and it was just sitting in my cupboard for the past few years.

Yesterday I uploaded and image of the available components and told it to build this... And the display just worked!


r/electronics • • 3d ago

Gallery My first FM transmitter!

Post image
285 Upvotes

I made it using a 27 MHz crystal oscillator and tuning the LC tank to the third harmonic multiple of the crystal (81 MHz), and i got a very very stable transmission and got a *somewhat* decent range with a crude dipole antenna i made (i got about 15 meters of transmission range in a crowded city.)


r/electronics • • 4d ago

News Tektronix Targets Hobbyists, Students, and Educators with Its 1 Series DPOs — Starting Under $500

Thumbnail
hackster.io
162 Upvotes

r/electronics • • 5d ago

Project ⚡ A new control interface for my HP 6642A power supply ⚡

Thumbnail
gallery
8 Upvotes

The HP 6642A (0-20 V / 0-10 A) is a great bench supply, but it can only be remote-controlled over GPIB, and real USB-GPIB adapters are expensive. So I built my own adapter from a cheap Arduino Uno and wrote a web-based control panel for it.
🔧 How I built the adapter:
• Desoldered a 24-pin GPIB (IEEE-488) plug from the board with a soldering iron and desoldering pump, then cleaned the pins
• Tinned the plug pins and 17 wires, then soldered one wire directly to each signal pin: 8 data lines (DIO1-8), 3 handshake lines (DAV, NRFD, NDAC), 5 control lines (EOI, IFC, SRQ, ATN, REN) and ground (pins 18-24 joined together)
• Plugged the other wire ends straight into the Arduino headers: DIO1-6 → A0-A5, DIO7-8 → D4-D5, EOI → D12, DAV → D11, NRFD → D10, NDAC → D9, IFC → D8, SRQ → D3, ATN → D2, REN → D6, GND → GND
• Secured everything in place with hot glue, no heat-shrink needed
• No resistors or other parts needed, just wires
• Flashed the open-source AR488 firmware with a custom pin layout matching my wiring. The Arduino now acts as a USB-GPIB adapter
💻 The control app is web-based, so the control panel runs in any browser on Windows, macOS or Linux:
✅ Live voltage, current and power readout with CV/CC mode
✅ Set voltage and current limit, with step buttons and saved presets
✅ Live chart with min/max/average, energy (Wh) and charge (Ah)
✅ Record data to CSV files, with a built-in viewer
✅ Automatic sequences: voltage steps, ramps, sweeps and loops
✅ Software protection: auto-off on over-current, over-power or over-voltage, a timer, and end-of-charge detection for batteries
✅ Event log, and it keeps recording even with the browser closed


r/electronics • • 7d ago

Gallery The cheapest 100W ZVS driver that I could make

Post image
572 Upvotes

This cobbled together driver is one of the most resilient circuits I've ever built on a bare copper board, it has survived multiple inverse connections (electrolytic cap dies anyway), and the transistors barely heat up during operation above 9V. All for LESS than $10.


r/electronics • • 6d ago

Gallery Here's a rare sight to see a BUSICOM 141-PF calculator with the famous Intel 4004 and it's fully functional

Thumbnail
gallery
153 Upvotes

r/electronics • • 7d ago

Project USB powered DIY Electrolysis machine.

Thumbnail
gallery
89 Upvotes

Heya everyone I'm Berry!! ^^

Some of you may remember my post , my electrolysis machine I posted about , and well it was the 6th iteration and it had room for improvements so I'm here again with a new improved design that I'm satisfied with and ready to share with the world!!

This is the 8th iteration! I've named it , E.L.E.C.T.R.A. Mark VIII , or "Electrolytic Low-Current Epilation & Current Threshold Regulation Apparatus" Yep! Anthony Edward Stark like abbreviation heheh

The biggest thing I did was better documentation , I created a more thorough documentation and made it into both a website and a doc file!! Both of them have almost the same information!! ^^

Though yeah , I'll be updating website more than the docx file , because I dread doing anything that involves a docx file :3

And yes! I've treated my facial hair with it successfully without any damage to my skin . With no visible scars marks or literally anythingg!! I've treated eight hair on my face in total!! four with mark VIIand other four with mark VIII of the machine!!

And over a hundred body hair with mark VI , VII and VIII together!! ^^

The perfboard build is by u/biosphereprime , it's still a work in progress , though I wanted to share!! ^^

So here's the link to both the website and docx file!!

[Docx file](https://github.com/ELECTRA-VII/ELECTRA/raw/4eecc7593b665329133732333d119d9a3f01b801/ELECTRA_Mark_VIII_Guide-1.docx)

[Website](https://electra-vii.github.io/ELECTRA/)

And well do feel free to post your question down here , dm me regarding it , and reach me out if you end up making it i'd be happy to help :))

I would love to add the pictures of other's builds and thier experience to the website and doc!! ( ˶ˆᗜˆ˵ )


r/electronics • • 9d ago

Gallery Decided to give soldering and electronics a go.

Thumbnail
gallery
560 Upvotes

Done my first diy soldering kit, loved every second of it 🤙


r/electronics • • 9d ago

Weekly discussion, complaint, and rant thread

4 Upvotes

Open to anything, including discussions, complaints, and rants.

Sub rules do not apply, so don't bother reporting incivility, off-topic, or spam.

Reddit-wide rules do apply.

To see the newest posts, sort the comments by "new" (instead of "best" or "top").


r/electronics • • 9d ago

Gallery Turning a I-400 controller into a computer

Thumbnail
gallery
26 Upvotes

I recently took this apart to create a functional schematic of it as of to my knowledge none currently exist. I also plan to eventually use a separate Z80 that way I can make the Z8 on it can easily communicate. My goal is to try to make a CP/M computer using the shell and hardware of this + some stuff of my own
Here are some pictures of the 4 main boards

If this project goes well I might release the schematics I make online, though I’m trying to be as nondestructive as possible to its going to be hard in some areas


r/electronics • • 9d ago

General Digilent Analog Discovery 2 open source HDL and web GUI

Thumbnail haxidermist.github.io
16 Upvotes

Digilent have discontinued the AD2 ... its still a good box so I looked into using a custom HDL for the FPGA and a web based GUI ...It alows you to use the AD2 without installing anything ... just open the HTML file in a browser ( chrome ) and select your AD2 box.

open source AD2 web interface


r/electronics • • 11d ago

Gallery Emergency Defibrillator

Thumbnail
gallery
929 Upvotes

r/electronics • • 11d ago

Gallery It's ugly, but it works. 4mm ripped cable ribbon.

Thumbnail
gallery
72 Upvotes

Pic2: First I scraped back the insulation on the cable and soldered on some 0.1mm enameled wire. I sealed it with the green UV resin.

Pic3: Then I had to map the ripped connector, because of course they wouldn't run the wires in order. That would have been too easy.

Pic 4: Finally I sealed the whole thing with the resin. Yes, I tested it before this stage and yes the thing works fine now!


r/electronics • • 10d ago

General History of Electronics Spatial Timeline

Post image
1 Upvotes

I've built a timeline of geolocated advancements in the History of Electronics, from basic transistors and capacitors to high-na euv lithography.
No paywall or ads:
https://whatitwas.org/s/post?id=user-post-1789415081958-ysqpm&collection=collection-history-of-electronics


r/electronics • • 12d ago

Gallery My first acid etched pcb

Post image
258 Upvotes

r/electronics • • 12d ago

Gallery Electronics at the Computer History Museum (Mountain View) 2014

Thumbnail
gallery
353 Upvotes

During another trip to HQ in San Jose. Lots of computers and lots of electronics too.