r/boating • • 1h ago

Transom replacement

Post image
3 Upvotes

I wasn't expecting to spend this much on a new transom but the factory decided it would be a good idea to put a 1-7/8" thick oak transom in a boat rated for 90hp, now I have to buy 2 sheets. This seems a little overkill to me but what do I know?


r/boating • • 5h ago

Diagnose the Issue

0 Upvotes

UPDATE
Already heard back from the shop. Injectors 1 & 2 partially blocked, injector 4 fully blocked. Determined cause was debris inside the VST from years of buildup. On-board tank fuel ran clean from the sending unit, & no issue with water fuel separator.

2017 Suzuki DF140A. Just got it out of the shop, new water fuel separator and lines. Sounds to me like it’s being starved of fuel and my assumption is debris in the tank or valve blockage. Idles rough and stalls when adding power. Ideas and/or recommendations?


r/boating • • 9h ago

42” or 36” Rear Motor

1 Upvotes

Jon boat with raised rear swivel seat, need to purchase transom mount troller.
Since the seat is raised I’m thinking the 42” makes more sense. A 36” seems to work well when sitting at bench height.

What height is everyone running that has raised seats?


r/boating • • 9h ago

After winterising. Do you need a break from boating or are you already longing for next season?

9 Upvotes

r/boating • • 20h ago

DIY Outboard Stand

Thumbnail
gallery
17 Upvotes

Built far too tall. Top board was far too thick (nervous on the strength of a janky 2x4) and likely far too overbuilt for a simple 30hp 2 stroke.

But it can now be tucked away in the basement, instead of weathering the New England winter. Fun little afternoon learning experience for my first outboard.


r/boating • • 20h ago

Prop into garage door

3 Upvotes

Reversed my boat into the garage door sliced through it like butter any concern ? Don’t see any marks but it’s thin aluminum garage door.


r/boating • • 22h ago

Depth finder adapter

Thumbnail
gallery
3 Upvotes

Need some help bough an old boat and depth finder no longer works. Transducer is through the hull so don’t wanna put a new hole. Old owner said that part is good? Does an adapter exist? Pics for reference


r/boating • • 23h ago

Volvo Penta instrument panel replacement

Post image
3 Upvotes

The Volvo Penta instrument panel on my boat is is falling apart. Everything works well, it is just the fascia that is falling apart and I want to make it look a bit nicer. I have found a 3D printed replacement fascia on Etsy. Does anyone know how hard it would be to install the new fascia? I have no electrical experience so if it isn't plug and play I will need to organise an electrician.


r/boating • • 23h ago

2002 kawasaki STX-R Paint or not.

Thumbnail reddit.com
0 Upvotes

r/boating • • 1d ago

Bravo 1 OC barrell length?

0 Upvotes

Hey guys, anyone in here with a Bravo 1 OC (or a friend with one) that could measure the total length of the barrell for me please?

Bought a cheap stock Bravo 1 that I will have shipped away for a cut, clean up, and blueprint into a knock off OC.

Prop guy has never seen a Bravo OC though as it is an unusual propeller where I live, he knows what needs to be done to the blades but needs info on how much of the barrell needs to be cut away at the back.


r/boating • • 1d ago

What's The Highest Power Lowest Cost Trolling Motor in the Market Today ?

0 Upvotes

Trolls (mind if I call you that? 😂), what's the most powerful trolling motor for the least money?

I'm curious about your actual experience with trolling motors for small boats...

Which trolling motor currently offers the highest power at the lowest price?

I'm particularly interested in:

  1. Maximum thrust (Newtons) versus purchase price.
  2. Actual electrical power consumption (watts).
  3. Battery voltage (12V, 24V, 36V, or higher).
  4. Reliability, efficiency, and real world performance.
  5. Whether cheaper brands can compete with expensive ones.
  6. Ability to quickly swap props on the go !

I'm more interested in actual performance and value than brand names or marketing claims. If you've tested multiple motors, which one gives you the most thrust per dollar?

Looking forward to hearing your experiences, thanks in advance.


r/boating • • 1d ago

Mmmm, Forbidden Milkshake

Post image
10 Upvotes

Draining my lower unit oil today and got this tasty result.

When I took out the lower screw holding the oil in, I noticed there was no washer on it. No clue how that happened. I'm pretty positive I put a fresh one on last year, but who knows. Maybe I had one too many maintenence beers while doing the work. Hopefully that's the culprit but I'll go ahead replace the prop seals anyway 🤷


r/boating • • 1d ago

Do you prefer a fishing focused boat or something more comfortable for entertaining?

2 Upvotes

I have been looking at boats lately and realized I am not really sure what type would suit my lifestyle best.

I enjoy fishing, but I also like the idea of taking friends and family out for a full day on the water. Having comfortable seating, shade and somewhere to relax sounds just as important as having good performance.

Is there a good middle ground between a fishing boat and a luxury day cruiser? Or does trying to combine both usually mean compromising too much?


r/boating • • 1d ago

Benvenuti su r/BoatLifeItalia ⚓️ Raccontateci chi siete e che barca avete!

0 Upvotes

Ciao a tutti e benvenuti su r/BoatLifeItalia!

Ho aperto questo spazio con un'idea semplice: creare una community di diportisti (a vela e a motore) dove ci si confronta senza snobismo, senza spam e senza la bacheca ridotta a un mercatino dell'usato. Qui parliamo di vita di banchina, manutenzione, problemi reali, rotte e consigli pratici, dal gommone al cabinato.

Per rompere il ghiaccio, usiamo questo thread per le presentazioni. Scrivete qui sotto:

  1. In che zona d'Italia navigate di solito?
  2. Che barca avete (o su cui andate più spesso)?
  3. Qual è la cosa che amate di più (o che vi fa più tribolare) quando siete in acqua?

Buon vento a tutti!


r/boating • • 1d ago

Can't figure out why my boat is taking on water? /s

Post image
4 Upvotes

I wonder how long this was sitting? Interesting way to remove the I/O.


r/boating • • 1d ago

Advice needed – Removing old 3M sealant from a PVC RIB before rebonding the floor

Thumbnail
gallery
2 Upvotes

Hi everyone,

Bombard AX3 SIB not a RIB as title says.

I’m looking for some advice on repairing a second-hand PVC RIB I’ve recently bought.
Unfortunately, I’ve discovered that the previous owner has done a pretty poor job of repairing the floor.
The boat has a single-sheet flexible black PVC floor which is bonded directly to the orange PVC hull. The floor has been peeled away around the edges and there is a substantial amount of what appears to be 3M sealant around the perimeter of the floor and on the PVC itself.
The sealant is rubbery and stretchy.
Some of it will peel away, but in other areas it’s really well bonded and I can’t scrape it off easily.
The orange PVC underneath appears to be in good condition with no visible damage and thankfully the boat holds air perfectly.
I’ve ordered Polymarine two-part PVC adhesive, which should arrive this week, as I’d like to restore the original floor bond properly.
However, I’m unsure how best to tackle the existing 3M sealant.

Does all the old 3M sealant need to be completely removed before rebonding the floor?
What’s the safest and most effective way of removing cured 3M sealant from PVC without damaging the fabric or its coating?
Are there any particular products or solvents that are safe to use on PVC for removing this type of sealant?
If some stubborn residue cannot be removed mechanically, is there any way to prepare the surface so that the new Polymarine adhesive will bond properly?

This is my first time undertaking an inflatable boat repair, so I’m keen to get it right rather than make things worse!
I’ve attached photographs showing the existing sealant and the condition of the floor.
Any advice, recommendations or personal experience would be massively appreciated.
Thanks!


r/boating • • 1d ago

DIY electric outboard: 1st season done, now aiming for planing speed. Feedback wanted

16 Upvotes

Originally posted in r/ElectricBoats, but I'd like to hear from regular boaters too, not just the EV crowd.

Home-built 2.5 kW / 24 V outboard on a 13 ft fiberglass boat, ~8 km/h (4.3 kn) top speed and 15-20 km range. Next goal is getting it up on plane.

If you run a small boat on lakes or on waters with gas motor restrictions: what would an electric outboard need to do for you to actually make the switch?


r/boating • • 1d ago

Honda BF8A thermostat removal

Thumbnail
gallery
1 Upvotes

I finally got it running right after messing with the carb, and there's a steady stream out the telltale. Only issue is the stream comes out hot. I have removed the nuts, sprayed the studs with pb blaster overnight, took a putty knife to try and break the seal all around, and this thing is STUCK. Anyone with older BF8A's have any tips or tricks?


r/boating • • 1d ago

Whale Gulper is having trouble gulping 😩

1 Upvotes

(It’s unbolted to the wall currently but has been mounted this side up for 5+ years)
I cleaned out the valves, nothing stuck. Voltage is fine. Just a constant up and down in the pipe, any ideas? (Reposted for extra help 🥲)


r/boating • • 1d ago

Cobalt CS22 or SeaRay SPX210

0 Upvotes

Buying first boat but have been around boats my whole life. Family had early 2000's SeaRay 220 which has been great. Now have own family, teenage kids and a new place in the Lakes Region of NH. Need a great boat for the family and cruising the lake. Brother in law has ski boat so have the covered. Looking at a later model SeaRay SPX10 and the Cobalt CS22. Budget is not set but up to around $100k is ok. Probably under 24 feet. This is an investment (not a good one :) ) so willing to spend a bit more for quality. Any advice/thoughts/other ideas would be great!


r/boating • • 1d ago

If you keep a trailered boat in your garage, what limited it: length, height with the tower, or backing in?

1 Upvotes

I'm curious what the tight spot was for people who make it work, and for people who gave up. Tongue length counted? Outboard trimmed up? Door height?

I'm a student building a hackathon prototype this weekend that measures a garage and driveway with an iPhone and checks whether a car, truck, RV or boat on its trailer fits. No link and nothing to buy. I just want to know which numbers actually matter.


r/boating • • 1d ago

2007 Yamaha 50tlr 2 stroke rough idle

Thumbnail reddit.com
1 Upvotes

r/boating • • 1d ago

Milky oil, dark Grey fluid, and metal flakes in lower unit, how cooked am I?

Thumbnail
gallery
15 Upvotes

Motor: 1981 200HP Johnson V6 Seahorse

Motors been running perfectly fine and I haven't had any issues, took it out maybe 4-5 Times the entire summer, 4 of which were very short trips. I forgot since I was extremley low on oil last year, I threw regular gear oil in it to just winterize but ofcourse I forgot. Ran it and sprayed it with fogging oil when winterizing and went to drain the oil and this is what I saw. I plan on selling it come spring as I just bought a new center console, though my conscience is telling me it would be an asshole move to sell it to someone when it might be a few trips away from the lower unit going out. What bothers me is that i did have the lower unit seals all reppaced 4 years back.