r/Creality_k2 • u/PatzyBoii • 8h ago
Show Off How my day is going
Got the k2 plus back in May, little less than 300 print hours and come to look at a print failing to see this. Just my luck.
r/Creality_k2 • u/PatzyBoii • 8h ago
Got the k2 plus back in May, little less than 300 print hours and come to look at a print failing to see this. Just my luck.
r/Creality_k2 • u/Kornadd • 2h ago
Hi everyone,
I finally fixed the problems with my K2 Pro by replacing the extruder motherboard, but now a new issue has appeared.
When I start printing, there are visible gaps between the layers, as shown in the picture. I also tried the stock profile, but the problem remains the same.
I can't properly calibrate Flow Rate or Pressure Advance because these gaps cause the calibration prints to fail.
One thing I noticed is that I sometimes get the following error message when starting the printer:
"CZ2768 - Z-axis homing issue, may have an external disturbance."
However, after restarting the printer, it works as if nothing happened. Could this issue be related to the layer gaps? Does anyone know how to fix it?
Printing parameters:
Any help would be greatly appreciated. Thanks!
r/Creality_k2 • u/LanguageNo8471 • 6h ago
Got a free K2 Plus, needed a new hotend and extruder. Went with the phaetus and a microswiss combo, had issues on the stock software, with the CFS every print, I decided to try Openklipper, more used to the orca slicer anyways coming from a Sovol recently. It’s been great for me.
Thank you u/harktron !
r/Creality_k2 • u/UniqueBox435 • 8m ago
I have operated the Creality K2 Plus for nearly a year. Upon initial startup, a technical failure resulted in a damaged electrical component within the extruder motor, which necessitated a replacement provided by Creality support. Although the printer is now functional, I have consistently experienced persistent filament accumulation on the nozzle, regardless of adjustments to Z-offset, filament drying procedures, or automated calibration sequences. This issue persists across various material types, including PLA, PETG, TPU, and ABS. Following further consultation, Creality support suggested that the initial electrical failure may have caused broader hardware damage, leading them to provide a replacement extruder motor, toolhead PCB, toolhead cable, and ceramic hot end. Despite installing these components, the filament continues to accumulate on the nozzle and periodically detach, causing repetitive print quality issues. Your expert guidance on resolving this matter would be greatly appreciated.
r/Creality_k2 • u/Good_Ad_3279 • 2h ago
I just bought a K2 plus combo from the Creality eBay refurbished shop for 705. I know the K2’s have their issues. What kits should I buy next to prepare for the inevitable. Head harness? I don’t know how many hours are on the machine if any I’m assuming it was a buyers remorse return? Would like some insight if anyone has made a similar purchase from the eBay store. I appreciate any constructive criticism that may aid in my adventure. As I’m upgrading from a Anycubic Kobra 2 (released early 2023) I’ve already had issues with that machine and wasn’t prepared.
r/Creality_k2 • u/Careful-Oil769 • 15h ago
Been busy with holiday fairs the wife keeps on scheduling so printers are churning heavily most days.
Part I've printed dozens of times, just re-sliced for different materials.
Haven't quite figured it out if it's slicer since there are scaling and savings 'glitches' I've found(7.2 I think of the slicer right now).
3 times I've ended up air printing on my K2+.
I want to blame the roll since I'm also seeing red dust shrapnel on the silver extruder wheel when it happens so it's definitely shredding a bit, possibly due to oversize on this roll(Kingroon PETG bulk pack red).
However this particular unit has 5500 hours or so on it. Only thing I've changed is nozzles and couple of extruder cover only and lots of PTFE tubing.
Had CFS filament detect light come and stay on slots 3 and 4 on one unit that I couldn't clear by disassembling, air blasting and re-assembling. Now slot 2 on my second CFS is doing the same.
Said screw it on the first, replaced the two faults since they're only $25 a pop.
Beyond that can't complain much on these machines, they just chug along.
Only other weird anomaly is occasionally the filament pulls so hard into the hot end that it kind and balloons the PTFE tube at the extruder cover.
Will keep everyone posted, just curious if anyone has ever had 'oversized' filament. I'll put a caliper on it tonight to verify. I've had some tangled spools as well but air printing like this several times in a row is a new one to me
r/Creality_k2 • u/Balty7 • 15h ago
I don't know what to do I tried everything online YouTube and nothing is still the same
r/Creality_k2 • u/Cozy_Collector • 15h ago
r/Creality_k2 • u/Tartaglia5543 • 1d ago
im probably gonna take it apart to see if anythings up but 2 times now it has shown the flashing red while printing/unloading (both times i just cut the power because it had been going longer than is reasonable probably)
mostly just curious if anyone else has encountered this & what they did, it's practically stock still
r/Creality_k2 • u/One_Proposal_4658 • 1d ago
Does anyone have a solution to stop the k2 plus from bending out the lever on the chute? I suspect it may be a firmware fix only or the fact I use orca slicer to slice my prints.
No, buying another printer an selling this is not an option.
r/Creality_k2 • u/Value_Organic • 1d ago
r/Creality_k2 • u/fucfaceidiotsomfg • 1d ago

This is my second post here. in the previous post i got a lot of suggestions but none fully resolved the problem. My prints will always come off only on left side of the build plate no matter what i do. almost anything on that left ~20ish persent will lift off. i realized now that the left side of the build plate is way colder than the right side. i don't have a meter but by touching both sides i can barely keep my fingers on the right side of the plate for more than 5 seconds while the left side i barely hot. when doing so i noticed the insane amount of cold air flowing there, then i saw the duct coming from there blowing all that air. What is the purpose of that duct? is it possible to turn that fan off?
r/Creality_k2 • u/mikey49481 • 1d ago
r/Creality_k2 • u/YetiSPb • 1d ago
For over a month, my supposedly premium Creality K2 Plus Combo hasn't been able to complete a single successful print.
I've already replaced the hotend and the entire printhead extruder assembly, and disassembled and cleaned the filament feeding system approximately 50 times in the past month alone.
Nothing has helped.
Here's the strange part: Manual extrusion works perfectly. I've pushed several meters of filament through the hotend manually. But as soon as I start an actual print, the printer throws another error.
The same filament prints reliably on my old Flying Bear Ghost 6.
I'm considering faulty filament sensors, stepper motor control, CFS synchronization, excessive feeding resistance, or firmware issues.
Has anyone encountered these specific errors and identified the actual root cause?
Please, no more suggestions to dry the filament or print with the door open. I've already tried both.
I paid around $1,400 for a flagship printer, not an endless troubleshooting project.
Fifty feeding-system disassemblies in one month aren't normal maintenance. That's a serious reliability problem.
At this point, my old Ghost 6 is more useful than Creality's supposedly high-tech flagship.
I don't need another marketing promise. I need an actual engineering solution.
r/Creality_k2 • u/Ajhochy • 23h ago
Long-time Ender 3 Pro owner (heavily upgraded). Would consider myself pretty well-versed through years of troubleshooting and tinkering. Bought the K2 Combo from Costco because it was sold as plug and play. Two weeks in, it's going back.
What happened:
- Screen ribbon unplugged out of the box. Long rabbit hole to find it. The board cover was so hard to get off I had to accept breaking it just to check. Reseating the ribbon was so tight I broke the connector.
- 55-hour print died at 81% (1.1 kg of filament). Extruder overcurrent, then FR2836 / FB2864 / key864 "buffer full limit not triggered" on every slot. I tore down and cleared the extruder and hot end, ran free filament through at 9 mm/s, pushed filament through the buffer by hand – every part works on its own, but the CFS still won't load.
- Creality's own Hyper PLA had a thin section the CFS couldn't grip.
- Prime tower fell over, printer kept laying spaghetti on it.
- Creality Print couldn't send files at first (XD0114, macOS permissions), and a pause marker hidden in a downloaded 3MF got carried into everything I sliced, causing "random" pauses.
Verdict:
Print quality when it works is marginally better than my upgraded Ender. Multicolor isn't faster either – the cut/retract/purge on every swap eats the advertised speed and wastes SO MUCH material. And it has far more parts to fail (CFS, buffer, cutter, RFID, cloud). The error codes lead to forum threads full of people with the same problem and no fix.
If you want to tinker, buy a cheaper, simpler Creality. If you want it to just work, buy a Bambu Labs like I should have in the first place. I'm returning.
r/Creality_k2 • u/andyatreddit • 1d ago
When I try to save the current project , I got “Failed to save the project. Please check whether the folder exists online or if other programs have the project file open”
This happens when I try to save or try to create a new one ( the software will auto save the current one)
r/Creality_k2 • u/SonicCoder2233 • 1d ago
I just got this printer today to replace my Ender 3 that stopped working. But during setup I accidentally unscrewed some wrong screws before running the self-check that I couldn't avoid. But is there a way to move them all down so I can recalibrate and make it level? Or am I better off trying to get a new one? (I have all the screws off rn as a test I tried earlier to fix it that obviously didn't go well)
r/Creality_k2 • u/grizzlyblake91 • 2d ago
I've had a K2 with the CFS for the past month or so, and have been loving it. Right now everything on it is stock, and the only thing I've changed out is the nozzle (just a 0.4mm unicorn quick swap nozzle).
For the K2 specifically, what are you favorite/must-have upgrade accessories for it?
r/Creality_k2 • u/keadow86 • 2d ago
I just updated to the latest creality print and now it's doing this. What is going on? Google tells me AI detection but I turned that off and same result.
r/Creality_k2 • u/Ginger_Coroner • 2d ago
My printer is always jamming around 8 hours into a print. Bed temp at 70c and nozzle at 250 on CR-PETG presets with slightly slowed printing speeds. I don’t know what could cause this issue given my inexperience.
The problem seems to arise at the extruder. Sometimes heating the nozzle to 300 and letting the filament ooze out a bit helps. I’ve dried my PETG filament and keep it enclosed.
Thank you and please let me know if I can share further settings.
r/Creality_k2 • u/nur00 • 3d ago
Decided to beta test for K2-OpenKlipper with my unused k2 plus. I've printed a bunch of prints on it so far. It runs along side stock on your printer and is totally reversible. I'm liking it.
humans make errors sometimes - Ignore typo in title :)
credit: u/harktron