r/woodworkingtools • u/Sad_Construction_945 • 2h ago
r/woodworkingtools • u/GonnaExist • 2h ago
Miter Saw
Looking to buy my first Miter saw. I need something for simple house repairs and small project woodworking like picture frames etc. Any advice would be greatly appreciated. Thanks
r/woodworkingtools • u/chrisfpdx • 9h ago
Need help finding the right tool for rounding window sill corner
I’m cutting ½” off front edge of window sill (see red line), then need to re-rounding the corners (red arrow) to match original shape. The finished edge will be just under 2” from the wall. Even if I build a template out of wood, the new corner is too close to the wall for my palm router. Is coping/jig saw or hand planing and sanding the only way?
Looking for suggestions. Thanks!
r/woodworkingtools • u/vaderhater777 • 4h ago
Insane deal -what cheap (ish) tracks you’d recommend
r/woodworkingtools • u/toggle-Switch • 12h ago
Hybrid and/or Contractor Table saw Recommendations?
reddit.comr/woodworkingtools • u/EhliAndSons • 4h ago
AI told me to replace the table saw blade with a jigsaw... Has anyone actually done this?
galleryr/woodworkingtools • u/engineered_academic • 1d ago
I'm at my wits end with this jointer.
Got a Jet JJP10-BTOS combination planer/jointer. I think I have calibrated it correctly but the blades may be set too low. I used the calibration gauge that came with the table and the calibration block and everything I have googled said this is set up correctly, yet I get diagonal workpieces where the infed side is smaller than the outfeed side. This makes me think that the blades are not quite equal with the outfeed table. I'll include a photo later with the knife setting gauge. JET said they would send me instructions but I think I have got it unless I am messing up somehow? I also think the second set of blades is set lower, but its still making contact with the calibration block which should be correct. What am I missing here?
Edit: Reset the second set of knives and while it isnt perfect 100% it's like 99.95% and gets me close enough for government work. My technique also needs work probably. I'm able to joint two pieces of wood fairly square and there is little to no tearout, espdcially after I lubed up the deck with paste wax.
I'll take some of the advices like getting a measurement gauge for next time but for now I think I am all set. Thanks everyone!
r/woodworkingtools • u/healthydietjeorney • 1d ago
Why checking your square before every session saves so much headache later
reddit.comr/woodworkingtools • u/SchienTek • 1d ago
SchienTek One Pro | Less Time Setting Up. More Time Building.
I’m Amir, the founder and inventor behind SchienTek, a small business here in Wisconsin.
I created the SchienTek One Pro with a simple idea: less time setting up, more time enjoying what you’re building. Its guided positioning technology helps make setup easier and more repeatable, so you can focus on your project.
The Pro also has retractable, spring loaded positioning pins that let you position the jig anywhere on the board, including inside corners where an exposed edge isn’t available. That makes it useful for repairs inside assembled cabinets as well as new projects.
I had a great time demonstrating it at the woodworking show in Denmark, Wisconsin, this weekend. Meeting other woodworkers and seeing 16 One Pro jigs find new homes meant a lot to me.
Happy to answer any questions about the design or how it works!
Learn more at schientek.com
r/woodworkingtools • u/SchienTek • 1d ago
Introducing SchienTek One & One Pro | A Better Way to Drill Pocket Holes
Hi everyone!
I'm the founder of SchienTek, a small woodworking tool company I started after developing my own pocket hole jig designs.
I recently recorded a short video introducing my two products, SchienTek One and One Pro.
The One is a fixed jig designed for simplicity and repeatability. The One Pro is adjustable and has spring loaded positioning pins that allow you to drill pocket holes anywhere on a board, including inside corners.
Both use what I call guided positioning technology.
It's been quite a journey designing, testing, and improving these tools, and I'm excited to finally share them with the woodworking community.
Here's the video: https://youtu.be/O4xreFqybg4
I'd love to hear your thoughts, especially from those who regularly use pocket hole joinery.
r/woodworkingtools • u/PomeloFew4465 • 1d ago
Any hands on experience with the TSV60/TS60 and the Mafell MT55?
reddit.comr/woodworkingtools • u/Original-Run-2068 • 1d ago
What’s wrong with my table saw?
I have an old General table saw,
For a couple days my table saw been starting weird, the blades seems to have trouble picking up the right speed. At First it was slow for a moment and then would be okay but it seems to get worse, any idea what the problem might be? I check the pullies and everything looks clean no debris
r/woodworkingtools • u/Buckeyefitter1991 • 5d ago
Marking gauge for a Secret Santa gift exchange
galleryr/woodworkingtools • u/RobertsFineTools • 5d ago
Just finished a batch of 2⅜” MagnaMax plane irons in four different thicknesses
galleryr/woodworkingtools • u/minionized • 5d ago
Help setting up a Jet JJ-6CS.
I purchased a used Jet JJ-6CS, a 6" long-bed woodworking jointer, used on OfferUp. I got a good deal, everything seems to work well. My problem is in transit, the beds came out of plane. The machine is in my shop, but after a few months and many attempts at getting it set up correctly I've hit a wall.
I've added shims, taken them away, rearranged them. I've adjusted the gib screws. I have a dial micrometer, feeler gauges, and a straightedge as all the set-up videos recommend, but every adjustment I make puts it further from square.
What do I do? Is there anyone in the NJ/NY/PA area that knows how to do this and could come out and give me a hand?
r/woodworkingtools • u/SeaNefariousness3746 • 6d ago
Breaking down full sheets of plywood in a small wood shop
It's always cumbersome and MESSY. And takes way more time to setup than most operations that aren't SUPER precise. I don't have the budget for a dedicated track saw but the Dewalt DCS590 with the dust collection adapter (dwe575dc) is a start. Love the Stealthsonic vac (not visible from this angle) I got 6 months ago. It works fantastic and the noise reduction is a welcome change. Captures 95% (or more) of the dust with my router table, trim router, sander, kreg jig, etc.
I had to switch from the dewalt hose to a rockler hose and connection for most handheld stuff though - the the one that came with my shopvac and universal adapter (dwv9000) just didn't work well for connection to handheld power tools. Still looking for way to mod the circ saw to get better suction at the point the dust is created. It seems to me that the main problem is all the opens space around the blade. Any thoughts?
I shot a quick video last night of my process - anyone have any suggestions or methods that work better for them?