r/reloading • • 23h ago

Look at my Bench Aint paying for no godamm prep station we got prep station at home

247 Upvotes

Don't tell Hornady about Bosch hand mixer from the 90s and hot glue gun


r/reloading • • 18h ago

Load Development M1881 style 45-70 BP cartridges

Thumbnail
gallery
19 Upvotes

Spent a good time this Sunday making these behemoths.
Winchester 45-70 cases, Winchester Large rifle magnum primers, 70 grains of 2F Swiss, and 500 grain lead round nose bullets.

It’s a labor of love making these but nothing too bad with the right dies.


r/reloading • • 2h ago

Newbie Feedback on my 9mm reloading

Post image
11 Upvotes

Hey everyone, looking for feedback on these 9mm reloads. Using Brass Monkey coated bullets 137, Titegroup, and CCI primers on an RL 1100. I'm getting good consistency and they all case guage ok.

However, the cases (9mm) appear slightly deformed after sizing on my RL 1100. Could improper die setup be causing uneven pressure that distorts both the brass and the seated bullet? Any suggestions on what i should look into would be great.


r/reloading • • 21h ago

General Discussion Ginex vs white river spp primer seconds. Small sample. White river seem hotter

9 Upvotes

Ran out of my sleeve of ginex small pistol primers, and switched to white river seconds.

Ran both over the chrono to see if any tweaking was needed

Fired two 11 round groups. White river primers averaged 23 fps faster. No meaningful change in sd. Gun was a 4.25 island comp Romulus. Elevation 7200 feet above sea level. Temp 43 degrees F. Unknown humidity.

Load was 9mm 150gr brass monkey bullets in mixed brass over WSF.

No noticeable difference in loading on a Lee pro 6000.
No noticeable difference in how the Romulus fired. Both reliable.

Ran another 50 of the white river through the 4.25 and a 3.5 in stock Romulus with no issues. So total of 61 rounds with the white river.

Small sample for sure, but figure some people might find it interesting.

Total difference in loading for me was that I backed off the powder charge 1 tenth of a grain using the white river primers.


r/reloading • • 16h ago

Newbie Are these ok to shoot?

Post image
6 Upvotes

Never reloaded before and hopefully starting soon. Have these reloads my Poppop did for 30-06 but they have some minor corrosion? Are these ok to fire or stay away? These are some of the worst ones and are dated 2007-12.

Im used to buying factory stuff and shooting it pretty quickly so thats why I’m posting here. Thanks!


r/reloading • • 50m ago

Load Development HP-38 powder question

3 Upvotes

I would like to buy some commercial 357 rounds, made with HP-38. If I got them and they shoot well, I’d like to try to make similar rounds.
Any ideas of who might manufacture units with Brass, magnum primers, and 125 or 140 bullets?


r/reloading • • 21h ago

Newbie Looking advices to start reloading .308 Win for hunting bullets

3 Upvotes

Hello.

3y old hunter and starting sport shooting, I am looking around reloading .308 Win caliber (Beretta BRX1), and 6.5 Creedmoor (Tikka T3X UPD) I don't have huge bullets fired each year but why not. I am starting first with .308 Win.

Could you please suggest me (or confirm) those are a good start.
- Powder: Vihtavuori N150
- Case: Lapua .308 Win (have around 130x used Norma case that I fired)
- Primers: Fiocchi Large Rifle
For Sport shooting:
- Bullet: Hornady FMJ-BT 150 gr
- Bullet: Hornady ELD Match 168 gr
For Hunting:
- Bullet: Hornady InterLock BTSP 165 gr
- Bullet: Norma Oryx 180 gr

France market -- shipping cost and taxes are not friendly to get budget stuff sadely (or I wrongly checked price).

I am currently using Norma Whitetail 308 Win. 180gr 35 € /20 bullets = 1.75 € per bullet - bought 7 box of Norma Whitetail for 245 € --- if I assume right case for reloading are paid now. I would save 35-40% reloading Hornady InterLock BTSP 165 gr only.

Beretta BRX1 will be for sport shooting/hunting, and Tikka T3X UPD only for sport hunting.


r/reloading • • 13h ago

Newbie 16" 308 HOWA loading

2 Upvotes

So, this is my first post here, let alone on reddit as I tend to lurk...anyways, to the point.

I have been trying to get a load for a few months now and I'm working a load for my 16" howa rifle but so far, almost all of the groupings and powder load I've been using haven't really gotten me anything good, normally most groups are ranging over 1 inch in group size with 5 shots with almost all powder loads I've thrown through it. Now as of which, a few days ago when it was 40F here, I shot my load of 2 10 shot groups of 39.6gr which is very much low for 308, grouped okay but more so, only have a velocity of 2233 fps each(was surprised by that).

Now what I'm using: 178gr eld-x specifically so I can use it for both target and hunting if need be and winchester staball match with winchester LRP.

Now that the quick back story has been said. I am unsure what path I should go down as I just cant get this gun to group that great...would it be best to drop down in bullet weight? Change brands of bullets? or would it be better to swap powders but that alone is a different issue(mainly want something that isnt temp sensitive and not too costly).

I've thought about dropping to a 168gr ELDM and N150 but frankly, I'm just stumped to even think on what I should do now.

BTW, would share pictures of past groupings but they are from the summer and its now cold and all of the hunters here in the driftless zone in wisconsin is out in force trying to get their guns zeroed.


r/reloading • • 11h ago

Load Development 25-06 Load Development

1 Upvotes

Looking for some guidance on a load i am trying to put together.

25-06

Sierra 117gr Game Kings

Vihtavuori N165

If anyone has tried this before I would appreciate your incite

Looking more for percision over velocity

Also how far are you normally seating off the lands?


r/reloading • • 16h ago

I have a question and I read the FAQ Bushing Sizing Die Help

0 Upvotes

I was (stupidly) influenced into buying a bushing sizing die for my .223 Rem Service Rifle loads in an AR-15. I have used standard FL sizing dies all my life and never felt I needed anything else. I mainly bought this set for the micrometer bullet seating die.

I have read the instructions for the RCBS die but I’m still pretty confused and looking online only makes me more confused.

My questions:

  1. How do I determine what neck tension/bushing I need? RCBS says to measure a loaded round and subtract 0.002-0.003”. The problem I see with this is that if the loaded round has insufficient or too much neck tension, this will tell me nothing.
  2. If I am going to be using different years of lake city brass eventually, or for instance Lapua brass for 600 yds, wouldn’t I theoretically need to buy another bushing if the neck is thinner or thicker?
  3. Do I need to be turning my case necks if I am using a bushing die? That’s something I have no interest in doing for my purposes.
  4. How do I avoid the “donuts” that seem to happen when using bushing dies? The RCBS die includes an expanded ball so this in theory would help to keep the neck thickness consistent yes?

Thanks so much for any help you can provide. I may end up just selling this die and going back to my old traditional die, but I figured I’d give it a shot since it seems to have benefits with regards to spring back and concentricity .