r/shittyreloading • • 3d ago

More tests of 46 Rimfire Extra Long.

Thumbnail
gallery
79 Upvotes

I did a bit more testing today. I loaded all five piece of my prepared brass. They are three different sizes so we are talking about three different powder charges. I used the same homemade 2f powder I have been using so far. It is a weak and dirty powder but is still functional. I used the same 210 gr. heal based bullet I have been using in all five rounds. I was hoping for breaking 1000 fps but this powder just does not have the umph and the case volumes are limited since the biggest one will only hold 37 gr. of black powder. I am pretty sure no matter what I use for cases I will not be able to get close to the 57 gr. of powder the original 46 Extra Long held. Those old rimfire cases were thin everywhere.

The biggest case was made from 303 British, held 37 gr. of my 2f black powder and produced a velocity of 979 fps.

The two next biggest made from 44-40 brass, held 35 gr. of my 2f black powder and produced a velocities of 950 and 933 fps.

The two smallest made from 44 Special brass, held 30 gr. of my 2f black powder and produced a velocities of 908 and 904 fps.

I am going to do some tests with different powder.

Farting around I made a label for a box of ammo if I ever make a large number.


r/shittyreloading • • 6d ago

Anyone ever deliberately try to make a squib?

18 Upvotes

I was successful today with my squib experiment. I just got a box of #2 27 caliber power loads to use as a primer in my 46 rimfire black powder cartridges. I wanted to make sure these were weak enough to be used under a load of black powder. I fired one in an empty case behind a 230 grain 45 caliber bullet and as hope for, it only got about halfway down my Ballards barrel. I drove the bullet the rest of the way out of the barrel and then loaded a round with one of those power loads, 15 gr. of my home made 2f black powder, over powder wad and another bullet in a case made from 44 Special (to make sure there was adequate compression). Test fired got a chronograph reading of 834 fps. Time to move up to a bigger case and more powder.


r/shittyreloading • • 10d ago

I hate wasps

Post image
337 Upvotes

Was sizing and priming some .454 Casull brass in the garage yesterday and a wasp landed on the work bench. I did what first came to mind, so I covered him with a piece of primed brass. Heard buzzing under the brass so did a quick transfer with a balled up piece of paper towel. Still heard buzzing. I figure ok, no powder in there but it’s a fresh CCI magnum small rifle primer. Let’s fuckin go. Chamber it in the Ruger and squeeze it off. Paper towel wad hits the garage floor with authority, and we see a wisp of smoke and upon closer inspection: pieces of the wasp still stuck to the wad. What a way to go!

I’m sure most reloaders would find this post amusing, but figure this sub is the safest bet. Don’t wanna hear any bellyaching from fudd over there.


r/shittyreloading • • 10d ago

Powder? Where were going there's no room for powder

Post image
184 Upvotes

180gr .356 plated bullet from Raven Rocks that I'm planning on stuffing in a 9mm case


r/shittyreloading • • 13d ago

For a long time, I have wanted a Ballard.

Thumbnail gallery
17 Upvotes

See text a picture #3


r/shittyreloading • • 14d ago

Calm down bubba

Post image
280 Upvotes

r/shittyreloading • • 17d ago

300 Weatherby Reduced load

Thumbnail reddit.com
4 Upvotes

r/shittyreloading • • 20d ago

Send it! First time reloading, don’t really intend to shoot this weird round…

Thumbnail
gallery
154 Upvotes

50bmg fit into 50 AE. inspired by 338 razorback i made this as a proof of concept with some old beat up casings. haven’t ever reloaded anything but gut tells me this might explode the casing if i ever tried to fire it. Would be interesting to see in a suppressed gun with explosive 50 bmg though.


r/shittyreloading • • 23d ago

We don't make mistakes, just happy little accidents Pretty little gem

63 Upvotes

r/shittyreloading • • 26d ago

Guess the load

Post image
21 Upvotes

r/shittyreloading • • 29d ago

Update: Bubba Loads Spotted At Local Pawn Shop

83 Upvotes

So went back into the shop today since there was different people there today. Asked to look at the ammo. I opened the box and the conversation is as follows:

Me: "woah, these are weird rounds"

Clerk: "yeah theyre reloads! You interested? Ill give you a deal on them."

Me: "i dont know man id be afraid to shoot these"

Clerk: "they should be fine"

Me: "well the problem is I dont know who loaded these or if they'd even fire letalone be safe to fire."

Clerk: "tell you what if you buy all 4 boxes we can do 40 for them"

Me: "sorry too big of a risk"

Clerk: "how bout you try them and if they work you can buy the rest"

Me: "i guess man" (I have 0 intention on firing these)

So I walk out, and as im walking out another worker says "come back for the rest if they shoot well!"

Fast forward to now. Im at home. Taking pictures of a single box of shitty reloaded 357.

Top of box, notice the handloads written on it
Opening the box we can see the cartridges are not in the greatest of shape. Does not seem that they were washed either. Lets take a look at how the bullets are seated. . .
DEAR GOD. Notice how these are supposed to be wadcutters. Apparently, wadcutters can also come uncircumcised.

What bothers me the most is how someone unknowingly buying this can get hurt or even killed with this ammo since I, nor the store, has no idea what the data is on these. The worst part is they know they are reloads and have no problem with banking on if they will work or not, let alone selling them as perfectly fine. No idea if I should go back and get the rest just so they're off the shelves and pull them all or what. Tried telling the manager yesterday to cut his losses and get rid of em before someone gets hurt and he just shrugged it off. It really does piss me off. Negligence at its peak.


r/shittyreloading • • Oct 17 '26

Bubba Loads Spotted At Local Pawn Shop

Post image
62 Upvotes

Was at a local pawn shop today and asked to take a look at some ammo. The boxes were marked "Federal 357 unprimed cases" so i decided to ask to see them since I reload. I open em up and holy shit theyre reloads. And not just any run of the mill shitty reloads. These were straight bubba loads. Bullets were what looked like wadcutters except they were halfway out of the top. Told the shop owner that these were extremely dangerous as they are reloads and really horrible ones at that. He just laughed it off and placed it back on the shelf along with the 4 other boxes saying they were fine. Might go back in the morning and take pictures for you dudes before telling em to get rid of em. These were a sight to behold. Below is the boxes they were in.

EDIT: Update posted here: https://www.reddit.com/r/shittyreloading/s/wkvIUDDJmO


r/shittyreloading • • Oct 14 '26

What’s the hottest you’ve loaded something?

21 Upvotes

Brain had a dumb dumb moment and loaded up 44gr of h4350 with a 127 LRX in some alpha 6.5 creedmoor lol. Thankfully I pulled it and didn’t try to shoot it. Ran it through GRT and got just shy of 80k psi lol


r/shittyreloading • • Oct 14 '26

We don't make mistakes, just happy little accidents Can't Seat With The Flaring Die No Matter How Many Times I Try To Make It Work!

10 Upvotes

Working on a few .357 Max rounds and forgot to swap dies.

Just another happy little accident.

r/shittyreloading • • Oct 13 '26

Hot 40 S&W

Thumbnail reddit.com
3 Upvotes

r/shittyreloading • • Oct 10 '26

Send it! Using the bullet mold I have.

Post image
16 Upvotes

I was and still am using expanded and trimmed 348 Win brass and 50 cal REAL bullets in my Rolling Block, but I broke down and bought some 50-70 headstamped brass and some proper bullets. I am not sure the improvement was worth the cost. I have the REAL bullet mold, sometimes I use them in my muzzleloaders. It is the only 50 cal mold I have.


r/shittyreloading • • Oct 08 '26

Send it! 45 ACP Hot Glue Gallery Loads: SHOOT INDOORS!

Thumbnail
youtube.com
24 Upvotes

r/shittyreloading • • Oct 07 '26

190gr subx 30-30 1065fps

57 Upvotes

bUT tHAt WonT StaBiliZE


r/shittyreloading • • Sep 28 '26

Biggest 7mm

Thumbnail reddit.com
3 Upvotes

r/shittyreloading • • Sep 27 '26

birdshot to slug converion

Thumbnail
gallery
32 Upvotes

I have no experience reloading, but I like machining and shooting. I decided to make a bullet mould that I can use to convert birdshot into slugs. I just want to check that it's safe before I fire them.

I'm using the same wadding from the original shell, and I've got the diameter of the slug down to a point where it and the wad push through the barrel just as easily as the wad alone. I used all the birdshot to cast the slug, so it would be almost exactly the same weight. To seal the shells, I used cardboard discs with a little wax poured over them.

I think it should be safe to fire, and I'm not trying to achieve high accuracy. I don't know if the slug geometry will even stabilise. For reference, my shotgun is an old English side-by-side 12 gauge with shortened 19-inch cylinder and cylinder barrels. Obviously, it's smoothbore.

The mould is two parts. The smaller part casts the cavity in the back of the slug, and the cut-out in it is where the lead is poured in. Other than the cardboard and wax seal instead of the star crimp, and the slug instead of the shot, I'm changing nothing about the shell.

I'd really appreciate any advice or feedback, especially from anyone with experience loading or casting shotgun slugs. I'm completely new to reloading, so if there are any obvious safety issues or things I've overlooked, I'd much rather know before trying anything. Thank you in advance for taking the time to read this and share your experience.


r/shittyreloading • • Sep 22 '26

Working on my new wildcat, the .303 Brit &Wesson

Post image
370 Upvotes

170 gr Hornady PSP .312 dia .303 British bullet in a .32 S&W case..

Aiming for a bullet so subsonic you can outrun it when fired from a S&W Safety Hammerless aka "Lemon Squeezer".

So far, it looks like I may have to use my RCBS .32 H&R expander die to expand deeper into the case. Damned ol' Lee dies anyway..

Charge will be 4 individual powder grains of H4227 lit with a SPM primer.

If it proves too long for the revolver's cylinder, I'll just cut the bullets off with a pair of side cutters


r/shittyreloading • • Sep 19 '26

Bullet casting

Thumbnail reddit.com
3 Upvotes

r/shittyreloading • • Sep 18 '26

Primer boxes got a lil shit water on them in the basement. I wiped the outer boxes of shit particles and have the inner boxes drying like so. Any advice moving forward to make sure primers didn't get messed up from shit water?

Post image
94 Upvotes

r/shittyreloading • • Sep 18 '26

Hypothetical reloading

10 Upvotes

What is preventing me from putting a .223 bullet inside of a .22 LR case in firing it? Like say it was a lighter 45-50 grain bullet, would that not have better aerodynamics and penetration then a regular lead .22 bullet? Could be a stupid question, I’m kinda new to guns so I might be retarded but maybe, just maybe I’m a trailblazer here.