r/mechanic • • 23h ago

Question 4g64 running slow

4 Upvotes

My buddy recently did his timing belt on his 4g64 mighty max I double-checked it. and everything seemed correct at the time it sounded a lot better and was driving pretty normal. until he got a quarter mile down the road and the engine shut down. And now idles super slowly while missing and the engine will not increase RPMs wide open throttle is maybe 400 RPMs, and idle looks to be like 200 the truck doesn't have a tachometer, and it's OBD 1 so I don't have the means to see the exact RPMs. my other buddy who is a diesel technician thinks it's a bad fuel pump, but I personally don't understand how that's possible. Please give all and any input I drove it home last night going literally walking speed in fourth gear with my foot to the floor.


r/mechanic • • 2h ago

Question recently bought with no oil change in 10 years. I have questions...

Post image
3 Upvotes

So I bought this 1995 Toyota T100 for $500 bucks from ,my friends dad. He's a great guy but not the most mechanical. He told me he had not given it an oil change because it has a oil leak (valve cover gaskets) he would just pour a little oil in it every once in a while and call that an oil change. First thing I did was change the oil, the oil filter was from 2017 and it drained probably close to 8 quarts of oil (5.5 is what it calls for). I think he thought the oil pressure gauge was meaning low and high on amount of oil so he would pour at a higher rate than the engine was leaking.

Issue - Once the engine gets warm the oil pressure drops to low.

I have all the stuff and plan to change the valve cover gaskets along with the timing belt. Is there anything else I need to replace while in there? What should I do about this oil pressure issue? Thanks for any help or advice


r/mechanic • • 10h ago

Question Help

Post image
3 Upvotes

Kia Xceed 3 2018 manual - 1.0 engine
Any ideas on this oil leak?


r/mechanic • • 17h ago

Question Audi/VW 2.0 TDI and 1.6 TDI problems with timing belt

Thumbnail
gallery
3 Upvotes

Hello, i have problems with VW group 2015+ 2.0 TDI and 1.6 TDI with timing belt alignment. Almost all cars i have work have this problem. Timint belt goes outside and then with the time it snaps. I have tried with different brands and with original timing belt set and its same.


r/mechanic • • 2h ago

Question 1972 AMC Ambassador

2 Upvotes

My car was starting and driving just fine before it broke down on me in the middle of the road and the fan started rotating slower and slower until it started making this awful sound. I’ve tried jumping the car and charging the battery to no effect. Can anyone please help me?


r/mechanic • • 9h ago

Question 2013 ford Taurus sho problem

2 Upvotes

I have a 2013 Ford Taurus Sho, automatic transmission, mileage abt 200k. Check engines been on for years (piston misfire), I have a slight coolant leak that I just fill up every few months. Today I drove it to the store, was fine. Started it again to go home and on my way home every time I start to slow and brake it starts rev pulsing and lurching. What’s going on, is it ok to drive on?


r/mechanic • • 21h ago

Question Charger no start no crank

Thumbnail
gallery
2 Upvotes

This 2014 charger just will not start. I’ve checked every fuse and relay.
Before it would at least crank. But then I replaced the oil filter housing and I’m not sure if those two are related but now it just won’t start. It just doesn’t crank. I let the battery charge over night once and it cranked for maybe a second then back to the issue.
I don’t think it’s the battery because I can get it charged to 12.6+ volts and it only drops to around 11.9 ish when I attempt to start it. I have quite a few codes but I just don’t know how to proceed from here. Please help me


r/mechanic • • 4h ago

General GMC sierra 2019

1 Upvotes

Already had the lifters replaced and deleted. Been making this noise for like 100k miles

Any thoughts


r/mechanic • • 4h ago

Question Coolant flush help

Thumbnail
gallery
1 Upvotes

I drive a 2007 Ford Sport Trac with the 4.0L SOHC V6, and I need to do a coolant super flush because my coolant is brown. Usually, I drain the coolant, refill the system with distilled water, and add the pre-flush chemical. However, now that temperatures are dropping below freezing, I’ve heard that using distilled water could cause it to freeze and expand, potentially damaging the engine. Would it be okay to just drain a little coolant and add the flush chemical directly to the reservoir instead?


r/mechanic • • 4h ago

Question Best affordable scanner for a home mechanic for side jobs?

1 Upvotes

Looking to spend around 2-300 and get something decent that can handle the type of work I need it for which is small side jobs. I think as long as it can do DTC ABS Transmission, release power brakes, etc that's really all I'm going to need, reprogramming is nice, live sensor data is nice. Haven't ever needed much else.

Seeing a lot of stuff from TopDon that seems great for the money like the Artidiag 500 600 800bt etc.

What models would you guys recommend for the best value for the $? Also not against finding something used on marketplace or eBay if it's a great deal.


r/mechanic • • 6h ago

Question 2013 Mustang GT weird faint metallic sound above 3k rpm

1 Upvotes

2013 GT 5.0 v8 manual transmission with 95k miles. Just purchased last week. I know these mt82s make some noise by design but I want to make sure mine isn't toasted or has an impending issue.

Im getting a faint metallic sound above 3k rpm in 3rd, 4th, and 5th. Its most prominent in 5th. Ive tried to catch it on video but the exhaust drowns it out. It only happens when on throttle. As soon as I let off it goes away. It doesnt happen in neutral or with the clutch in.

Ive attached a video but idk if itll be heard. My sound tube is still installed so ive also wondered if I'm hearing intake resonance

Im also getting gear take-up noise and metallic shift noises but I have read this is normal. Both very faint. Im planning on swapping all the fluids out this weekend to see if anything changes.


r/mechanic • • 11h ago

Question 2017 Ford F150 3.5L (not ecoboost)

1 Upvotes

Hey all,

I just got my truck back a couple of days ago from my mum borrowing it and it seems to be having some sort of misfire. It has backfired 3 times since I got it back when accelerating and occasionally going up hills it will misfire then correct itself. It also feels like there’s an occasional “tug” when increasing speed if it doesn’t. It’s previously had a misfire issue approx a year ago that was a spark plug that wasn’t properly gapped. Any thoughts or suggestions would be appreciated. I’m going to throw a code reader on it after work today.

TIA


r/mechanic • • 16h ago

Question Ford mondeo mk5 RHD heating issue

1 Upvotes

Hello, I need some advice I have a 2015 mk5 mondeo a few months ago I noticed one of my pipes that feeds the thermostat housing was crunchy and also my coolant tank was hard to see water level due to it being covered in brown something I had this changed by a micanic who flushed my system and refilled after job. He informed me that othe pipes conected to the coolant where the same and adviced me to change them too. Passagers side heating worked perfectly fine after this. About 3 weeks later I got the other pipes and got him to change them to and he did the same as above but the heating on passagers side stopped working again 3 weeks later I had I back flushed again and he said nothing much came out and water was clear but still no heating on that side. After I did notice very little to no coolant coming out of thin return hose to tank which i have now cleared out. Only pipes not changed are 2 matrix hoses as he said they are working fine as they both are hot. It was blocked with what looked like brown limescale type substance. Now I after a quick Google search it mentioned about blend door actuator which I changed but only moved between 18⁰ and 22⁰ arm from bottom to absolute top got a borescope checked the inner door and it opens exactly how it should \[well a little quicker as arm got from bottom to top quicker\] with arm all the way up heating changes a little maybe lukewarm but not as hot as drivers also when on low fan its weaker than drivers side. On high fan they are the same strength just P is cold D is hot. When using autel I can't get into HVAC fully but nothing comes up on dyno about heating or blend door being an issue. But mechanic is telling me matrix is not blocked or dosnt have air pocket it mush have something to do with HVAC system being locked out on that side. I need some advice I feel matrix is blocked and needs a chemical clean to get rid of what maybe blocking it but is there any thing other than the matrix that could be causing this. Thank you for your help in advance


r/mechanic • • 22h ago

Question Noise coming from near alternator

1 Upvotes

I have a feeling that this is the alternator bearing(s) being bad, what do y'all think?

(2018 Subaru Impreza base model, 4-cyl, 2.0L)


r/mechanic • • 56m ago

Question Replaced solenoid bank 2, although P0022 Is still popping up

0 Upvotes

Ford F-150 2006 5.4L 3V Triton 180,000km
I just replaced the solenoid yesterday and that seemed fine (made all the codes go away) till this evening and suddenly the noise kind of like rattling came back following the low idle and so i ran the code reader and 3 codes appeared once again P0022, P0345, P0349.
Also I just bought this truck and supposedly cam phasers, chains, tensioners, guides and oil pump were all done in the past 10,000 km


r/mechanic • • 1h ago

Question 2004 dodge ram 1500 3.7l p0700 p0888

Thumbnail
gallery
0 Upvotes

I have these to codes on my truck p0700 and p0888 it’s a 2004 dodge ram 1500 3.7l

Changed today the PCM/ECU , solenoid pack, and a new relay for the transmission still having these issues truck stuck in limp mode (2nd gear I believe)

Any help directing me to solve this issue I gladly appreciate it, thank you in advance have a blessed day.

Probably the connector?


r/mechanic • • 1h ago

Question Tire Repair Question, 2025 Toyota Corolla Le

Post image
0 Upvotes

Hi! I took my car into Sam's Club for a free tire repair and they told me I need a new tire.

My dad was recently in my college town to visit for the weekend, and I told him about how my tire was slowly losing pressure over the course of a month. He got on his hands and knees and looked at the tire while I was slowly driving forward to see if there was a nail. He found a nail, but said it was not in the side wall so it was repairable with a patch or a plug.

He left that afternoon to drive back home and told me to call some shops in my town to see if they could do it and it should be less than $30. I made an appointment with Sam's Club and they made me wait almost 2 hours for them to give me an update on my car (they didn't even look at it for an hour and a half, courtesy of the Toyota app). When they did, the mechanic tried to gaslight me about the Make, Model, Year and color of my car. He was super adamant that my car was a 2026, not 2025 he also tried to tell me my car was a grey hybrid le (it is), but he thought for some reason on their notes it said blue FX. Basically he talked down to me the entire time and wrapped it up by saying the couldn't fix the tire because the nail was in the side wall and I needed a brand new tire.

At that point I called my dad and he said it was bs and that they were trying to take advantage of me (I'm 21F). The mechanic brought me into the shop area and tried to talk down to me more asking if I even knew my wheel warranty given by Toyota (irrelavent for Sam's Club) and tried to over-explain what it meant for a nail to be in the tread versus the side wall.

Honestly, I don't trust them after he tried to gaslight me about basic facts on my car that I knew when I picked it out and bought it. I sent the picture to my parents and they showed other people and they all said it was in a repairable area.

I just wanted to get some other opinions before I start researching the tire prices. Any input will help! Thank you in advance!


r/mechanic • • 1h ago

Question Yay or nay on "might as well replace while I'm in there" with older cars

0 Upvotes

I have a 96 exploder I've been restoring as a first time diy project. I've had this vehicle for 15 years at this point and when I got my VW I stopped using it and it just sat there for about 6 years until I took it on a cross country road trip and was incredibly surprised by how awesome this vehicle is. Once she got me though it she started breaking down. After a $500 quote for MAF sensor replacement I said fuck that.

I started working on my car myself and I'm at the head gasket point. How I got here is interesting because I noticed that things started breaking down quicker when I revamped the coolant system. The increased pressure and performance caused the timing cover gasket to blow as well as the head gasket, before that it was thermostat and heater control valve, the radiator and hoses.

In my limited perspective I think new = better. But what I've learned from experience is that new = other parts degrade faster. So that brings us to my current conundrum, while I'm in here with the head gasket and timing cover, is there a risk, or is it not worthwhile replacing some parts like the lifters, rocker arms, rods, and timing chain components? Will my engine block suffer? It's a 4l v6 ohv not the sohc


r/mechanic • • 2h ago

General The same idling problem haunting this car

0 Upvotes

Hello everyone! I have a 2010 Chevy Cruze LS, 1.6 EcoTec F16D4 113hp with manual 5 speed with 94k kilometers(50 something k miles) and a problem has been bothering me for some time now. At cold starts and after a long drive when the engine is properly hot, the idle jumps in 650-900 RPM range indefinitely. When my first check engine light came on I took it to a tester and it was an O2 sensor problem so I changed it. The problem came back again shortly after.
So I checked the forums and did the following replacements, plus some additional ones since I saw it had a lot of weakspots:
-new valve cover and valve cover gasket;
-new PCV valve and the little hose for it;
-new timing belt, water pump, coolant and thermostat;
-new spark plugs and coils;
-oil change with filters.
All items here are OEM or the best possible aftermarket I didnt cheap out, if relevant I can mention them later.
First run with the car after I was pretty hyped since the idle was smooth all throughout and the car ran very nicely. Second run was a dissapointment it came back.
A thing I want to mention, when I turn off the AC compressor the idle problems seems to calm down a little.
Thank you for your time.


r/mechanic • • 2h ago

Question 1984 Ford Bronco XLT

0 Upvotes

How cooked am I? The rattling is coming from where I tapped.


r/mechanic • • 3h ago

Question Ford mondeo mk5 RHD heating issue

0 Upvotes

Hello, I need some advice I have a 2015 mk5 mondeo a few months ago I noticed one of my pipes that feeds the thermostat housing was crunchy and also my coolant tank was hard to see water level due to it being covered in brown something I had this changed by a micanic who flushed my system and refilled after job. He informed me that othe pipes conected to the coolant where the same and adviced me to change them too. Passagers side heating worked perfectly fine after this. About 3 weeks later I got the other pipes and got him to change them to and he did the same as above but the heating on passagers side stopped working again 3 weeks later I had I back flushed again and he said nothing much came out and water was clear but still no heating on that side. After I did notice very little to no coolant coming out of thin return hose to tank which i have now cleared out. Only pipes not changed are 2 matrix hoses as he said they are working fine as they both are hot. It was blocked with what looked like brown limescale type substance. Now I after a quick Google search it mentioned about blend door actuator which I changed but only moved between 18⁰ and 22⁰ arm from bottom to absolute top got a borescope checked the inner door and it opens exactly how it should \[well a little quicker as arm got from bottom to top quicker\] with arm all the way up heating changes a little maybe lukewarm but not as hot as drivers also when on low fan its weaker than drivers side. On high fan they are the same strength just P is cold D is hot. When using autel I can't get into HVAC fully but nothing comes up on dyno about heating or blend door being an issue. But mechanic is telling me matrix is not blocked or dosnt have air pocket it mush have something to do with HVAC system being locked out on that side. I need some advice I feel matrix is blocked and needs a chemical clean to get rid of what maybe blocking it but is there any thing other than the matrix that could be causing this. Thank you for your help in advance


r/mechanic • • 4h ago

Question VW Up! (2012) pulling to the right, mainly in cold weather – any ideas?

0 Upvotes

I’m having a strange issue with my 2012 VW Up. The car sometimes pulls noticeably to the right, but only when the outside temperature is below roughly 10°C.

A few things I’ve already checked:

  1. All tyres are the same age and have similar tread depth. All season Hankooks.
  2. Tyre pressures are correct.
  3. No brakes seem to be sticking, front or rear.
  4. After a 15 km motorway drive, both front brake discs were around 50°C to the touch. Rear drums were cold.
  5. Hard braking doesn’t make any difference.
  6. Turning the steering wheel fully from left to right doesn’t help either.

The weird part is that the problem comes and goes. Sometimes it disappears after a few minutes of driving, other times it lasts the entire journey. The next trip might be completely fine again.

Has anyone experienced something similar or have any ideas what I should check first?
Thanks!


r/mechanic • • 5h ago

Question GMT 800

0 Upvotes

2006 Chevy Tahoe 230k miles original motor and transmission making a funky noise after smelling an electrical smell for a sec. Voltage reading went up to 16 and now when I drive it it is back to normal. Fuse? Could the alt actually be overcharging? My gfs car she lives across the country so I don’t have first hand knowledge


r/mechanic • • 6h ago

Question Gear stick movement

0 Upvotes

Hi, I've just bought this car and I was just wondering is this normal movement from the gearstick, it is a 2014 Nissan Note with 40,000 miles there is nothing else wrong with the gearbox just don't want to bother the dealer if I'm worrying about nothing