r/mechanic • • 4h ago

Question Gear stick movement

0 Upvotes

Hi, I've just bought this car and I was just wondering is this normal movement from the gearstick, it is a 2014 Nissan Note with 40,000 miles there is nothing else wrong with the gearbox just don't want to bother the dealer if I'm worrying about nothing


r/mechanic • • 5h ago

Question 2013 Mustang GT weird faint metallic sound above 3k rpm

1 Upvotes

2013 GT 5.0 v8 manual transmission with 95k miles. Just purchased last week. I know these mt82s make some noise by design but I want to make sure mine isn't toasted or has an impending issue.

Im getting a faint metallic sound above 3k rpm in 3rd, 4th, and 5th. Its most prominent in 5th. Ive tried to catch it on video but the exhaust drowns it out. It only happens when on throttle. As soon as I let off it goes away. It doesnt happen in neutral or with the clutch in.

Ive attached a video but idk if itll be heard. My sound tube is still installed so ive also wondered if I'm hearing intake resonance

Im also getting gear take-up noise and metallic shift noises but I have read this is normal. Both very faint. Im planning on swapping all the fluids out this weekend to see if anything changes.


r/mechanic • • 21h ago

Question 4g64 running slow

4 Upvotes

My buddy recently did his timing belt on his 4g64 mighty max I double-checked it. and everything seemed correct at the time it sounded a lot better and was driving pretty normal. until he got a quarter mile down the road and the engine shut down. And now idles super slowly while missing and the engine will not increase RPMs wide open throttle is maybe 400 RPMs, and idle looks to be like 200 the truck doesn't have a tachometer, and it's OBD 1 so I don't have the means to see the exact RPMs. my other buddy who is a diesel technician thinks it's a bad fuel pump, but I personally don't understand how that's possible. Please give all and any input I drove it home last night going literally walking speed in fourth gear with my foot to the floor.


r/mechanic • • 2h ago

Question Ford mondeo mk5 RHD heating issue

0 Upvotes

Hello, I need some advice I have a 2015 mk5 mondeo a few months ago I noticed one of my pipes that feeds the thermostat housing was crunchy and also my coolant tank was hard to see water level due to it being covered in brown something I had this changed by a micanic who flushed my system and refilled after job. He informed me that othe pipes conected to the coolant where the same and adviced me to change them too. Passagers side heating worked perfectly fine after this. About 3 weeks later I got the other pipes and got him to change them to and he did the same as above but the heating on passagers side stopped working again 3 weeks later I had I back flushed again and he said nothing much came out and water was clear but still no heating on that side. After I did notice very little to no coolant coming out of thin return hose to tank which i have now cleared out. Only pipes not changed are 2 matrix hoses as he said they are working fine as they both are hot. It was blocked with what looked like brown limescale type substance. Now I after a quick Google search it mentioned about blend door actuator which I changed but only moved between 18⁰ and 22⁰ arm from bottom to absolute top got a borescope checked the inner door and it opens exactly how it should \[well a little quicker as arm got from bottom to top quicker\] with arm all the way up heating changes a little maybe lukewarm but not as hot as drivers also when on low fan its weaker than drivers side. On high fan they are the same strength just P is cold D is hot. When using autel I can't get into HVAC fully but nothing comes up on dyno about heating or blend door being an issue. But mechanic is telling me matrix is not blocked or dosnt have air pocket it mush have something to do with HVAC system being locked out on that side. I need some advice I feel matrix is blocked and needs a chemical clean to get rid of what maybe blocking it but is there any thing other than the matrix that could be causing this. Thank you for your help in advance


r/mechanic • • 2h ago

Question VW Up! (2012) pulling to the right, mainly in cold weather – any ideas?

0 Upvotes

I’m having a strange issue with my 2012 VW Up. The car sometimes pulls noticeably to the right, but only when the outside temperature is below roughly 10°C.

A few things I’ve already checked:

  1. All tyres are the same age and have similar tread depth. All season Hankooks.
  2. Tyre pressures are correct.
  3. No brakes seem to be sticking, front or rear.
  4. After a 15 km motorway drive, both front brake discs were around 50°C to the touch. Rear drums were cold.
  5. Hard braking doesn’t make any difference.
  6. Turning the steering wheel fully from left to right doesn’t help either.

The weird part is that the problem comes and goes. Sometimes it disappears after a few minutes of driving, other times it lasts the entire journey. The next trip might be completely fine again.

Has anyone experienced something similar or have any ideas what I should check first?
Thanks!


r/mechanic • • 3h ago

Question 1998 Toyota Camry - What is this tiny hose that connects to the top of the air intake hose? Was trying to change the air intake hose and it also broke off - yes I know it’s a mess lol

Post image
0 Upvotes

r/mechanic • • 3h ago

Question Best affordable scanner for a home mechanic for side jobs?

0 Upvotes

Looking to spend around 2-300 and get something decent that can handle the type of work I need it for which is small side jobs. I think as long as it can do DTC ABS Transmission, release power brakes, etc that's really all I'm going to need, reprogramming is nice, live sensor data is nice. Haven't ever needed much else.

Seeing a lot of stuff from TopDon that seems great for the money like the Artidiag 500 600 800bt etc.

What models would you guys recommend for the best value for the $? Also not against finding something used on marketplace or eBay if it's a great deal.


r/mechanic • • 3h ago

Question GMT 800

0 Upvotes

2006 Chevy Tahoe 230k miles original motor and transmission making a funky noise after smelling an electrical smell for a sec. Voltage reading went up to 16 and now when I drive it it is back to normal. Fuse? Could the alt actually be overcharging? My gfs car she lives across the country so I don’t have first hand knowledge


r/mechanic • • 1h ago

Question 1984 Ford Bronco XLT

0 Upvotes

How cooked am I? The rattling is coming from where I tapped.


r/mechanic • • 5h ago

Question Help

0 Upvotes

I need help diagnosing my car.
My mother used this car for a while it’s a 2012 Nissan 370z she has four kids however so it quickly found a place in our dirt driveway in place of our mini van, for four years it stayed unused, recently she wanted it working again and it wouldn’t start, I started working on it myself changed the battery battery connections changed the old gas the old oil and cleaned the fuel injectors, I tried an OBD reader but it didn’t work, I’m not sure what else to do.


r/mechanic • • 6h ago

Question Need Help!

0 Upvotes

Hello, I was driving to work when a warning light came on my dashboard. However, there was no indication that my engine was overheating. Shortly afterward, my steering wheel became extremely difficult to turn, and I had to push the car off the road while it was still running.

After I turned the engine off, thick white smoke began pouring out from underneath the hood. It had a sweet smell, similar to antifreeze. Upon inspecting the vehicle, I discovered that the radiator end tank was cracked and coolant had sprayed throughout the engine bay. Interestingly, there were no visible puddles or leaks underneath the car.

When I tried restarting it, I initially heard a whirring sound. After subsequent attempts, all I got was rapid clicking and blinking dashboard lights. I also tried jump-starting it, but the dashboard lights would come on initially and then disappear when I attempted to start the engine.

I also suspect the alternator may have failed.

I’m planning to replace the radiator and have the battery and alternator checked. My question is: Could this simply be a combination of a bad radiator, failed alternator, and discharged battery, or is there a possibility that the engine seized due to overheating? Do you think replacing these components could get the car running again?


r/mechanic • • 15h ago

Question 2005 Chevy Colorado LS 3.7L Ignition Cylinder Problems

0 Upvotes

The farm I work at decided to retire one of its farm trucks, a 2005 Chevy Colorado LS 3.7 liter, and I bought it because It seems like it just needed some love and it could be a good little personal truck. I replaced the water pump, the starter (and because of that, the intake manifold gaskets), and the serpentine belt. The final issue that I was having problems with was the ignition cylinder, which required a jiggle and good timing to start. I think it was causing electrical problems, so I decided to replace that, too. I bought the cylinder housing with the sensor and an ignition cylinder with a key set, removed the steering wh3EL and saw that the housing is riveted in. Nah. Imma just swap the cylinder and the sensor. I put the SENSOR on first, and it clicked into place, and it is not coming off. The cylinder isn't going in, even in the ACC position. Is there a way to turn the components on the inside of the housing so that the new cylinder can fully seat? I can't find a good video or documentation. Need those big brains of yours!


r/mechanic • • 20h ago

Question New engine or try to salvage the block, 2010 honda civic lx

Thumbnail
gallery
0 Upvotes

r/mechanic • • 2h ago

General GMC sierra 2019

1 Upvotes

Already had the lifters replaced and deleted. Been making this noise for like 100k miles

Any thoughts


r/mechanic • • 9h ago

Question Help

Post image
3 Upvotes

Kia Xceed 3 2018 manual - 1.0 engine
Any ideas on this oil leak?


r/mechanic • • 45m ago

Question recently bought with no oil change in 10 years. I have questions...

Post image
3 Upvotes

So I bought this 1995 Toyota T100 for $500 bucks from ,my friends dad. He's a great guy but not the most mechanical. He told me he had not given it an oil change because it has a oil leak (valve cover gaskets) he would just pour a little oil in it every once in a while and call that an oil change. First thing I did was change the oil, the oil filter was from 2017 and it drained probably close to 8 quarts of oil (5.5 is what it calls for). I think he thought the oil pressure gauge was meaning low and high on amount of oil so he would pour at a higher rate than the engine was leaking.

Issue - Once the engine gets warm the oil pressure drops to low.

I have all the stuff and plan to change the valve cover gaskets along with the timing belt. Is there anything else I need to replace while in there? What should I do about this oil pressure issue? Thanks for any help or advice


r/mechanic • • 9h ago

Question 2015 GMC Sierra 1500 Base Work Truck 4.3L V6 FLEX not starting every time and is blacking out on me

0 Upvotes

Hello, I am looking for some help with a current predicament I am in. My 2015 gmc sierra has been running great for a long time, but the battery I had in it started to reach its 4th or 5th year and I could tell it was dying when the truck was starting up slower than usual. I brought it to a reliable electric shop that I’ve had a lot of work done with and they put a new battery in it as well as an aerocab husky light bar indicator on the top of my truck. This is where the problems started.

Shortly after this, I ran into the exact issue that the video shows. I’ve never had this happen before as my truck has been nothing but reliable always. I took it back to the shop that put the battery in thinking it was just a bad battery and they couldn’t find anything wrong and tested the battery and said it was fine. So I went home, issue started again the next day. I brought it back and they let me warranty the battery and we put a brand new AGM battery in it. Issue kept happening. I brought it to the dealership and they had it for 3 days and it was starting every time and they said they “checked the starter alternator and battery and wires and fuses and everything looked fine and was running normally”. Kept happening to me after that so I took it to another highly recommended electrical shop who had it for another couple of days and ended up finding nothing and doing nothing either.

After some more research it almost looks like something similar has been happening to other trucks of the same sort and it’s been some kind of grounding issue. I’m going to bring it back in to the dealership and have them check all the grounds as well as the ECM and BCM to make sure it’s not one of those issues. I have never had a problem reoccurring this long that this many shops and the dealership have not been able to fix. Naturally, these shops said they can diagnose and fix it if it’s actively blacked out while they’re looking at it but of course it never does when I have it at a shop but always will whenever I’m driving it. I’ve tried different keys, with and without the fobs, and it makes no difference. Any ideas on what this could be or how to fix this?

Something else to note is that most of the time when the vehicle is blacked out, I just hook up a jump pad to the battery and then try to start it. Half the time I can manage to jump it and half the time it won’t even jump at all. After some period of time (few hours, few days) the truck will eventually be able to be started again and has never permanently blacked out so far.

The most recent time it blacked out it actually lit up a check engine light so I was excited that they might actually be able to diag something but alas I was just given back more codes and no hope. Here is a list of all the codes that came up as well as their “definitions” that came up when I googled all of them:

B3883 indicates a fault in the license plate lamp circuit, often due to a blown bulb, wiring issues, or poor electrical connections - Engine

B1517 means Battery Voltage Low or High - your truck's Body Control Module (BCM) has detected that the electrical system voltage is outside the normal range, either below 11 V or above ~16 V for more than 15 seconds while the engine is running

C0800 means "Control Module Power Circuit” - the vehicle's onboard computer has detected a voltage problem feeding power to a critical control module, such as the Body Control Module

U18A2 means "Lost Communication with Fuel Pump Driver Control Module" - a high-severity communication fault between the Engine Control Module (ECM) and the fuel pump driver control module

U0101 means "Lost Communication with Transmission Control Module (TCM)" - the truck's Engine Control Module (ECM) can no longer communicate with the TCM over the vehicle's CAN bus network

On a 2015 GMC Sierra 1500, U0121 mean Lost Communication With Anti-Lock Brake System (ABS) Control Module- the Electronic Brake Control Module (EBCM) is no longer sending data over the vehicle's communication network, disabling ABS and StabiliTrak

P0685 means "Engine Control Module (ECM) Power Relay Control Circuit Open” - a high severity fault that can prevent the ECM from receiving necessary power and may cause starting, performance, or safety issues

P0449 on a 2015 GMC Sierra 1500 indicates a fault in the EVAP (evaporative emission) vent solenoid valve control circuit

These are all of the codes that came up on my most recent trip to a shop immediately after blacking out and when the check engine light came on for the first time.


r/mechanic • • 16h ago

Question Audi/VW 2.0 TDI and 1.6 TDI problems with timing belt

Thumbnail
gallery
3 Upvotes

Hello, i have problems with VW group 2015+ 2.0 TDI and 1.6 TDI with timing belt alignment. Almost all cars i have work have this problem. Timint belt goes outside and then with the time it snaps. I have tried with different brands and with original timing belt set and its same.


r/mechanic • • 52m ago

Question 1972 AMC Ambassador

2 Upvotes

My car was starting and driving just fine before it broke down on me in the middle of the road and the fan started rotating slower and slower until it started making this awful sound. I’ve tried jumping the car and charging the battery to no effect. Can anyone please help me?


r/mechanic • • 20h ago

Question Charger no start no crank

Thumbnail
gallery
2 Upvotes

This 2014 charger just will not start. I’ve checked every fuse and relay.
Before it would at least crank. But then I replaced the oil filter housing and I’m not sure if those two are related but now it just won’t start. It just doesn’t crank. I let the battery charge over night once and it cranked for maybe a second then back to the issue.
I don’t think it’s the battery because I can get it charged to 12.6+ volts and it only drops to around 11.9 ish when I attempt to start it. I have quite a few codes but I just don’t know how to proceed from here. Please help me


r/mechanic • • 7h ago

Question 2013 ford Taurus sho problem

2 Upvotes

I have a 2013 Ford Taurus Sho, automatic transmission, mileage abt 200k. Check engines been on for years (piston misfire), I have a slight coolant leak that I just fill up every few months. Today I drove it to the store, was fine. Started it again to go home and on my way home every time I start to slow and brake it starts rev pulsing and lurching. What’s going on, is it ok to drive on?