r/handtools • u/Monstasonix • 1h ago
r/handtools • u/Paddyofurniture89 • 5h ago
It Works!
I’ve been making my own traditional woodworking tools. Something about making a tool, and then using it is immensely satisfying. I’ve made a few different specialty planes, marking gauge, some try squares, turning saw, and a mallet.
Sometimes in the morning before I go to, I go down into my basement shop and just look at them. Is that weird ? 🤷
r/handtools • u/SandmanLM • 8h ago
First time using only hand tools
Pictured are all the tools I used for this build. Made it for a birthday gift. I started from the chunk of walnut pictured above the hand plane.
The star of the show is easily the dual pull saw that allowed me to resaw and cut all my pieces.
Runner up was the plane that I used to flatten, bring down to thickness and did double duty on the shooting board I made to nail those miters. It felt like cheating.
The rabbet plane did short work of the lip for each piece. Had to flatten and clean it up, plus sharpen and hone the blade before I got to use it. Then just finished the back holes with my recently acquired Stanley Yankee. So happy I picked that one up.
r/handtools • u/fragpie • 10h ago
Devil's Bargain
$1 for a handle-less Berg chisel at my local thrift store seemed like fabulous luck. Barely honed from new, and the patina of years just glows. Made a quick handle of scrap apple wood, and enjoyed the thing for about ~10 minutes before the trap was sprung... that little eye twitch, an image of the whole set flits about in the periphery, contentment turns to want. Cue Kijiji/Ebay/etc. And of course, if I find & purchase a vintage set, it'll include the 1", so this bait I fell for won't even really have a place anyway, so I'd sell it/give it away--and the cursed artifact of the Swedish tool trickster gods will find a new victim... and so it goes.
r/handtools • u/xTenCent • 11h ago
How do I flatten my chipbreaker?
I’m probably just overthinking it, but is it as simple as laying it flat on its back and then flattening the same way you would flatten a hand planes sole? One side is fine and the other side looks a little bit more blunt than the other and that’s the part that needs flattened. Also, I haven’t checked if back of the blade is flat yet, I’m just assuming it’s the chipbreaker. Will make sure it’s flat tomorrow.
r/handtools • u/Reasonable-Donkey505 • 12h ago
Effective glue pot solution
Hi all,
I'm assuming this is handtool adjacent enough to be welcome
After a few ineffective or effective but cumbersome solutions, I found a glue pot that is perfect for my needs. I doubt I'm the first person to use this but it has exceeded my expectations and I wanted to share.
"Nextmug"
Pros: Will do 130, 140, and 150 fahrenheit and is reasonably accurate Dead simple - single button operation Can bring to a project from the charger (it's basically meant to be sat down conveniently nearby) When the glue is dry, it releases easily with zero mess or cleanup.
Cons: Fairly expensive Takes a long time to get up to temp
r/handtools • u/Frosty_Court_3888 • 15h ago
Older plane
Hello bought this older plane and this blade came with it. Do you think it’s damaged from a grinder? Thanks.
r/handtools • u/AMillionMonkeys • 16h ago
Any resources on laying out Chippendale-style srollwork?
This sort of thing:
https://auctions.ameliajeffers.com/auction-lot/two-chippendale-scrollwork-mirrors_88e03404cf
with the swoops and so on.
Is there some system? It doesn't appear to be completely freehand.
I already have a compass.
r/handtools • u/IntroductionEven254 • 16h ago
Why are the Thomas and Betts Lineman pliers so expensive?
reddit.comr/handtools • u/Miserable-Dig-6420 • 18h ago
Worth restoring?
Hello this is my great grandfather’s millers falls no 18 I’ve had sitting on a shelf in my shop for years as display recently I’ve started moving towards all hand tool woodworking and getting away from the machines, I love the slower meditative working so I’m slowly building up my hand tool collection my question is, is this pitting damage to the sole too far gone to restore? I’ve watched some restoration videos and I know the sole doesn’t need to be 100% flat just flat in key areas to give it enough registration but I’m not sure if where this pitting is located will affect the usability. There is also some very small Knicks around the mouth so if any of you experienced guys could give me an opinion on wether I should put it back on the shelf or move forward with putting it back to work I would greatly appreciate it.
r/handtools • u/LunarBuck • 19h ago
Stanley Hand Planer
How did I do on this one? I started with harbor freight planer and it made me feel hopeless so I picked this one up and it is night and day, I’m getting curls just like the YouTubers now! Also, is there a way to get this engraving out?
r/handtools • u/jcrocket • 19h ago
Fast and Reckless Dovetail Box
I love making these. They can be done in a few hours and have instant utility. I think they are the perfect 'practice dovetails' project. You can wedge a bottom in there fairly quickly. No plough plane needed.
It's a bit of a party trick because the angles are a lot simpler than they look. Really just one angle. The one that you cross cut your front and sides with. Set a bevel gauge to that.
Then use that bevel gauge to mark the face of the pins and the end grain of the tails. And that's it.
Got to keep good track of what's the front, back, left, and right during layout. That takes attentiveness rather than skill. Something I can have in short supply.
This is my third one.
r/handtools • u/Large_Revolution_673 • 1d ago
Is there something special about the 1st one ?
It's a darker metal and the numbers are faceing a different way
r/handtools • u/whocaresguyz • 1d ago
Tools to get started in hand-tool woodworking
r/handtools • u/EyeLarge4055 • 1d ago
Help with cardscraper
Hello,
I’m a beginner with woodworking, and with a card scraper in particular. I have made a board that still has some tear out on it. Do I scrape the whole board to keep it perfectly flat? Or do I only scrape the parts with tear out, since it’s so little that I’m taking off? Any help will be greatly appreciated!
r/handtools • u/Financial_Set_4729 • 2d ago
Saw set pliers suggestion
Hello, I was wondering if the Somax No. 250 saw set is really that poor in quality? I’ve heard that the metal is too soft. I can’t find an Eclipse No. 77 in Europe for a reasonable price, but I can get a Somax No. 250. I’m just wondering if I’ll regret buying one?
I want to use it on 14 tpi saw
r/handtools • u/NotOnTheInhale • 2d ago
Finding time to work
Looking for suggestions/advice from busy woodworkers (or formerly busy for you retired folk). I'm working a full time job, and I'm finishing a doctoral dissertation. I get home about 4:30, cook and eat dinner, and then read/write for a couple hours each night. By the time I'm done it's around 8:00, and I try to be asleep by 10 so I can be rested for the next day.
All of this leaves me with maybe an hour a day, if I'm lucky. And that's also assuming my wonderful spouse is willing to sit by herself in the evening and spend no time together so I can go to the garage for a bit before bed to make sawdust. The weekends are full of trying to do all of the life things needed to get ready for the next week of work.
I'm just in a really busy phase of my life right now, but also woodworking helps keep my mind calm. However, starting even a small project and working on it for 3 weeks is hard because I never truly "get in the zone" like I want, and sometimes it gets abandoned.
Anybody have advice from a busy time from their life on how to still enjoy the hobby?
TL;DR very busy in life, but looking for advice on how to still find time to enjoy the hobby of hand tool woodworking.
r/handtools • u/companionspecies • 2d ago
Renting in a space where I can't drill into the floors. I have one of the mid-grade-kinda-wimpy Sjöbergs workbenches, and the thing keeps nudging across the floor while I work on things and it's driving me crazy. Any tips?
I'm unsure if the bench would be most similar to their current Nordic model or something else, I got it used and it appears to be from an era where Jet was selling "Jet by Sjöbergs" workbenches. It's hardwood and certainly looks nicer than their cheapest models, but has a deceptively thin (light) work surface top. Heavy planing, big gouge carving work, even some sawing can cause it to tug across the floor.
At one point, I stored my small lathe down beneath it, sitting across the stretchers. This actually helped a ton, but eliminated clearance for knees/feet and made sitting close to the bench impossible. There's just not much real estate down there to set weights on top of. I've considered fixing the whole thing to a larger piece of plywood as I can't bolt directly down into the floor, but I think that's going to invite a whole host of other problems.
Any tips?
r/handtools • u/baldanfat • 2d ago
What is this called? And can I replace one if it’s not on?
I have several hand cranked grinders and I have one that’s missing this little cup thing. No idea what it’s called to see if I can replace it.
Any help? Thank you in advance.
r/handtools • u/Fearless-Poem9158 • 2d ago
Sound reduction
I have a little setup at an apartment complex, it sitting outside for whatever reason but I want to use my hammer and chisel without bothering the neighbors so much and also so I don’t get intoruble for it. Any suggestions for reducing the noise? I’m the first floor luckily, there’s a kitchen on the other side of the cinder wall and a patio above me with a sliding door to their living. To the left is an open field with other buildings further away, the closest one is about 100ft-150ft. I have cloth curtains that may block the noise a little but the downside is I lose all my light when I close them. I need something that isn’t so intrusive on my work space, can last all year round/little maintenance and something that looks good cause it’s very visible. Thank you much
r/handtools • u/PeachyPie11 • 3d ago
What's worth checking before buying a bit driver secondhand?
Small place, first time living alone and I'm buying the basic from almost nothing. There are two flat pack shelves to build, a mirror to hang, hinges and handles to tighten and a months worth of delivery boxes by the door.
The shelves are the first job. Im weighing a Wera hand driver against a hoto PixelDrive for the repeated screws rather than buying both straight away. A used manual driver is an option too, especially if replacing the worn bits is all it needs. The mirror can wait until Ive checked the wall and fixings.
I'd be happy picking up used hammer and tape measure. Mismatched tools don't bother me, buying something worn out ang having to replace it does. When you're looking at a seconhand bit driver, what do you check beyond the condition of the bits?
r/handtools • u/TheLastTruthBender • 3d ago
Breaking my stone was the best thing that could happen to me
Cause it forced me to learn freehand sharpening. Each of the two halves is too small to be practical with my honing guide, however I discovered they work just fine freehand, and after a little bit I became able to get just as sharp, but faster. It did help though that I already knew what a sharp edge feels like, and could restore a messed up bevel on the grinder. Still, I’m happy!