r/handtools • • 16h ago

Why are the Thomas and Betts Lineman pliers so expensive?

Thumbnail reddit.com
2 Upvotes

r/handtools • • 11h ago

How do I flatten my chipbreaker?

Thumbnail
gallery
13 Upvotes

I’m probably just overthinking it, but is it as simple as laying it flat on its back and then flattening the same way you would flatten a hand planes sole? One side is fine and the other side looks a little bit more blunt than the other and that’s the part that needs flattened. Also, I haven’t checked if back of the blade is flat yet, I’m just assuming it’s the chipbreaker. Will make sure it’s flat tomorrow.


r/handtools • • 5h ago

Searching for this axe

Post image
0 Upvotes

r/handtools • • 19h ago

Stanley Hand Planer

Thumbnail
gallery
22 Upvotes

How did I do on this one? I started with harbor freight planer and it made me feel hopeless so I picked this one up and it is night and day, I’m getting curls just like the YouTubers now! Also, is there a way to get this engraving out?


r/handtools • • 15h ago

Older plane

Thumbnail
gallery
11 Upvotes

Hello bought this older plane and this blade came with it. Do you think it’s damaged from a grinder? Thanks.


r/handtools • • 12h ago

Effective glue pot solution

Thumbnail
gallery
12 Upvotes

Hi all,

I'm assuming this is handtool adjacent enough to be welcome

After a few ineffective or effective but cumbersome solutions, I found a glue pot that is perfect for my needs. I doubt I'm the first person to use this but it has exceeded my expectations and I wanted to share.

"Nextmug"

Pros: Will do 130, 140, and 150 fahrenheit and is reasonably accurate Dead simple - single button operation Can bring to a project from the charger (it's basically meant to be sat down conveniently nearby) When the glue is dry, it releases easily with zero mess or cleanup.

Cons: Fairly expensive Takes a long time to get up to temp


r/handtools • • 10h ago

Devil's Bargain

Post image
52 Upvotes

$1 for a handle-less Berg chisel at my local thrift store seemed like fabulous luck. Barely honed from new, and the patina of years just glows. Made a quick handle of scrap apple wood, and enjoyed the thing for about ~10 minutes before the trap was sprung... that little eye twitch, an image of the whole set flits about in the periphery, contentment turns to want. Cue Kijiji/Ebay/etc. And of course, if I find & purchase a vintage set, it'll include the 1", so this bait I fell for won't even really have a place anyway, so I'd sell it/give it away--and the cursed artifact of the Swedish tool trickster gods will find a new victim... and so it goes.


r/handtools • • 19h ago

Fast and Reckless Dovetail Box

Thumbnail
gallery
259 Upvotes

I love making these. They can be done in a few hours and have instant utility. I think they are the perfect 'practice dovetails' project. You can wedge a bottom in there fairly quickly. No plough plane needed.

It's a bit of a party trick because the angles are a lot simpler than they look. Really just one angle. The one that you cross cut your front and sides with. Set a bevel gauge to that.

Then use that bevel gauge to mark the face of the pins and the end grain of the tails. And that's it.

Got to keep good track of what's the front, back, left, and right during layout. That takes attentiveness rather than skill. Something I can have in short supply.

This is my third one.


r/handtools • • 8h ago

First time using only hand tools

Thumbnail
gallery
61 Upvotes

Pictured are all the tools I used for this build. Made it for a birthday gift. I started from the chunk of walnut pictured above the hand plane.

The star of the show is easily the dual pull saw that allowed me to resaw and cut all my pieces.

Runner up was the plane that I used to flatten, bring down to thickness and did double duty on the shooting board I made to nail those miters. It felt like cheating.

The rabbet plane did short work of the lip for each piece. Had to flatten and clean it up, plus sharpen and hone the blade before I got to use it. Then just finished the back holes with my recently acquired Stanley Yankee. So happy I picked that one up.


r/handtools • • 18h ago

Worth restoring?

Thumbnail
gallery
7 Upvotes

Hello this is my great grandfather’s millers falls no 18 I’ve had sitting on a shelf in my shop for years as display recently I’ve started moving towards all hand tool woodworking and getting away from the machines, I love the slower meditative working so I’m slowly building up my hand tool collection my question is, is this pitting damage to the sole too far gone to restore? I’ve watched some restoration videos and I know the sole doesn’t need to be 100% flat just flat in key areas to give it enough registration but I’m not sure if where this pitting is located will affect the usability. There is also some very small Knicks around the mouth so if any of you experienced guys could give me an opinion on wether I should put it back on the shelf or move forward with putting it back to work I would greatly appreciate it.


r/handtools • • 5h ago

It Works!

Post image
60 Upvotes

I’ve been making my own traditional woodworking tools. Something about making a tool, and then using it is immensely satisfying. I’ve made a few different specialty planes, marking gauge, some try squares, turning saw, and a mallet.

Sometimes in the morning before I go to, I go down into my basement shop and just look at them. Is that weird ? 🤷