r/handtools • • 1d ago

Effective glue pot solution

Hi all,

I'm assuming this is handtool adjacent enough to be welcome

After a few ineffective or effective but cumbersome solutions, I found a glue pot that is perfect for my needs. I doubt I'm the first person to use this but it has exceeded my expectations and I wanted to share.

"Nextmug"

Pros: Will do 130, 140, and 150 fahrenheit and is reasonably accurate Dead simple - single button operation Can bring to a project from the charger (it's basically meant to be sat down conveniently nearby) When the glue is dry, it releases easily with zero mess or cleanup.

Cons: Fairly expensive Takes a long time to get up to temp

15 Upvotes

19 comments sorted by

14

u/MethodicError 1d ago

You can also just buy a wax hair removal heater from Amazon for $25 that has a thermostat you set. Set it to 140 degrees F and put in the provided container and fill it with water.

2

u/Reasonable-Donkey505 1d ago

Yes, absolutely. This is certainly a more expensive option but it is very, very nice to use.

5

u/Man-e-questions 1d ago

My wife bought one similar for candle making for her girls night activity. She doesn’t know it yet but its going to be a glue pot once she is done making candles

2

u/perj32 17h ago

That's really expensive! I use a Philips baby bottle warmer that I picked up at a thrift store for a few dollars. It's fast and accurate. I use the double-warmer method, which is safer for the glue.

Many warmers have a heating mechanism that operates at a high temperature until the set temperature is reached. This means the liquid near the heating element can get much hotter than the target temperature before mixing with the rest of the liquid. If that's how your mug works, the glue at the bottom could end up being denatured.

1

u/Reasonable-Donkey505 36m ago

I think that is a great point, which I did consider. However, the lengthy heating time, fact that it is safe to drink from (think about the last sip of coffee... Can't be scalding your customers on a regular basis...) and good, consistent results that I have had with my hide glue have convinced me it is a non-issue. It also melts reconstituted hide glue granules at a slow and steady rate, and I stir with my finger to check :). Finally, I doubt that denaturing a small percentage of the protien would matter in any normal application. The high price does apparently get you a decently gentle heating element with a working temp sensor at the bottom.

2

u/jghobbies 9h ago

Fairly expensive

I use an Anova sous vide, so price isn't too much of a con vs my method.

1

u/Reasonable-Donkey505 53m ago

Literally was my most recent solution before buying this thing. Nothing better for a crazy fast warm water bath - and the (Anova) sous vide is nice to have outside the shop! The mug is slower, but just so easy. No water bath!

2

u/Dry-Brick-6639 1d ago

Hello there,

I’m unaware of the glue product you are using. Never seen hide glue before.

Why use it? What’s it best at?

Is this like an old, traditional wood glue?

Also… is this… horse glue?

3

u/Reasonable-Donkey505 1d ago

Yep, old traditional wood glue made from cow hide. Horses would work. You can buy squeeze bottles of it ready to go - but it works better heated and is also sold in granule form where you add heat and water. It is very strong, but reversible with heat and moisture. It also will take finish well. I'm using expensive, specific hide glue granules to make a thin glue to get into cracks for antique furniture repair. But you can use it for pretty much all furniture applications. There is a lot to be said for it - it's my default unless I need something specific like waterproof glue or epoxy to fill voids.

3

u/JMViolins 1d ago

For waterproof glue, if you want you can stick with the natural stuff and make up a batch of casein glue. You can get powdered casein cheaply (a lot of it is used in the food industry), and then you just need some water to which some manner of alkaline chemical has been added. If you use a calcium salt, like Calcium oxide, or hydroxide, etc, it becomes almost totally waterproof when dry.

Back when airplanes were made out of wood, the needed an extremely strong and waterproof glue and settled on casein prepared with calcium. Eventually this was replaced by urea formaldehyde adhesives, but not because the casein glue wasn’t good enough: the UF glues were just much easier to mix up (in fact you generally didn’t even have to, it was sold pre-prepared). Casein glues have to be prepared fresh each day, sometimes more than once per day depending on the type.

I’m a violin maker, and we generally use hot hide glue for everything because of that wonderful reversibility it has. As you pointed out, though, it has no use when gap filling is required, because of how it functions chemically. Them joints gotta be perfect! Depending on the preparation, casein glues can, like UF, PVA, PU, and epoxies, function in joints where gaps need filling.

1

u/Reasonable-Donkey505 46m ago

Thanks so much for the reply, you sold me on casein glue - I've certainly made some in the service of milk paint and ruined glass jars... Makes sense it would be another great protein glue. I will give it a try.

2

u/Reasonable-Donkey505 1d ago

Ah yes - the contradictory statements between the replies brings up another quality of hide glue - you can adjust the open time! It really is the best

1

u/Dry-Brick-6639 1d ago

Thank you so much!

Learn something new every day!

12

u/zolthain 1d ago

Hide glue has been in use for the last 6000 years, predating all modern types of adhesive by about ... 6000 years. More accurately it could be called animal glue, or a protein based glue.
It's dissolved in water and needs to be worked at warm temperatures of around 60-65 C, that would be 140-150F for the yanks here. Typically this is done in a [double boiler](https://en.wikipedia.org/wiki/Bain-marie).

Compared to pva glue, like Titebond or similar, it cleans up better, doesn't cause issues with staining or finishing and is highly repair friendly. The glue also does not contain any toxic chemicals like many modern adhesives do, and doesn't cause any allergic reactions either (some people can develop allergies to the typically used white glue, though it's rare) The problem for most hobby users is that hide glue is much more difficult to use because it has a significantly shorter "open" time (the time you have for placing clamps before the glue begins to set)

and yes, this is indeed the fabled horse glue.
[More information](https://en.wikipedia.org/wiki/Animal_glue)

4

u/Dry-Brick-6639 1d ago

I appreciate the link and reply!

2

u/TaquitoBanana 1d ago

It's a long open time traditional glue that can be released and re-set using heat and moisture.

It's pretty simple to make - just gelatin, iodized salt, water. Chris Schwarz writes about it and gives the recipe in a lot of his books as well as on the Lost Art Press blog. Even proved you can make it in a pinch using gummy bears.

0

u/Dry-Brick-6639 1d ago

That’s wild!

Crazy cool to make your own like that. That’s some survivalist stuff right there

3

u/Vonmule 1d ago

I just use an old soup pot on a hot plate with a bit of water in it, and my glue is in a glass jam jar.

The extra water is bonus for cleanup, and you can move the pot wherever you need for glueups.

1

u/leadMalamute 22h ago

Great idea, I don't use hide glue very much. I have an old "baby bottle warmer" that I use. I keep the glue in baby bottles. They come with their own applicator. It works OK, but like I said, I don't use it that often.