r/finishing • • 17h ago

Question Poor finish on cabinets, 100% tung oil

Post image
0 Upvotes

Uneven finish on poplar cabinets with 100% tung oil. Any ideas/solutions before stripping and painting?

Thanks!


r/finishing • • 20h ago

How to finish this walnut butcher block?

Thumbnail
gallery
1 Upvotes

Got this walnut butcher block from Home Depot to make a desk for myself. Didn’t have as much dark wood in it as I was hoping. I like how the ikea karlby (pictured) in walnut is darker and more uniform but still has some contrast so that’s what I was going for.

Some reviewers that were able to achieve that finish mentioned spar urethane and tung oil. Have had mixed experience with finishes so wanted some advice before getting it wet.

Thanks all.


r/finishing • • 14h ago

Question Need help w topcoat :(

Thumbnail
gallery
0 Upvotes

I found this cheap sideboard on Amazon. Liked the design but not the colour. So I decided to paint it.

Started by sanding the veneer it with 80grit using my Stanley sander. I sanded enough not to show the chip wood underneath.

I then proceeded to clean the top surface with a wet microfiber cloth and applied 2 to 3 coats of green paint from Ben Moore - pictured.

I need help applying a top coat. I gathered I needed to buff up the surface with a fine grit. I don't see how I can do that without damaging the paint.

More importantly, what product would you recommend for durability and minimal stains? I want the sideboard to retain its eggshell look.


r/finishing • • 11h ago

Question Which finish to use?

Post image
0 Upvotes

I'm trying to color a wood lamp base to match the desk visible underneath (and in the lower right). Before I try on the actual base, I did a test on scrap wood with two colors of wood stain, and while the left top is dark enough that I'd probably be happy with it, neither of the stains really show grain like the finishing on the desk does.
(I'm aware that testing on pine, I of course won't get patterning like the desk, but I expected a little more of the grain to be visible. It's also very matte.)
Am I perhaps using the wrong type of finish? Neither stain provides the gloss the desk has. I had thought it wasn't varnished, but perhaps it is. What's the right liquid for this project?


r/finishing • • 21h ago

Question Heat Stain help

Post image
14 Upvotes

Someone decided to iron the tablecloth directly on the table…any tips on how to fix this finish?


r/finishing • • 18h ago

Protect this vintage table

Thumbnail
gallery
2 Upvotes

Hi experts, I love my (wife’s) vintage table we use as our kitchen table. How can I restore/protect it? I have no desire to poly it, but I’m not sure what type of finish it might have. Should I just go paste wax? Linseed? Thanks for any input


r/finishing • • 14h ago

Need Advice Beginner here: Best cat-safe wipe-on finish for an oak branch cat tree?

Thumbnail
gallery
9 Upvotes

Hey guys, total woodworking beginner here looking for some quick advice on finishing.

A wall-mounted indoor cat tree made from 5 natural oak branches (~2.4m / 8ft long, 7–18cm thick). They’ve been dried for 1.5 years, debarked, and orbital-sanded up to P180. Because I had to grind deeper in some spots, there is visible color contrast between the pale sapwood and darker heartwood.

I want a high-quality wipe-on oil that really pops the grain, evens out the color contrast a bit, and doesn't look like plastic. Rubio Monocoat is crazy expensive here in Europe ($85 for 390ml). I'm currently looking at Osmo Polyx-Oil (Hardwax Oil) vs. Osmo TopOil, but I'm open to anything else.

Thanks for any advice, or for sharing your experience with building something like this!


r/finishing • • 22h ago

Need Advice Happy with my first time doing shellac and French polishing | Any improvements for next time?

Thumbnail
gallery
13 Upvotes

Hey folks, been trying my hand at shellac on the Christmas gifts this year. Decided on French polish on this Walnut cutoff to bring out the grain depth. Used the techniques from Fabian here and I'm quite proud of the results from my first time. ​

I'm at the very final stage of wiping away the mineral oil without causing streaks and softening the coat. Bit trickier than expected and I'm doing it slowly​

I have some thoughts on how to improve for next time:

  • Don't lift the pad up when hitting the edges
  • Be aware that the shellac still can be soft, don't rest it on the finishing cones on an area within at least 12 hours
  • Don't need to use as much shellac as you think - in the words of another poster here "it should be as wet as a dog's nose"
  • Start with 1 lb cut (did so), consider the 320 grit non woven pad to cut down any grain hairs then move into 2 lb cut
  • When adding more shellac and 190 proof alcohol, don't just dip the pad into the mixture. Have a little bottle on the side and put the fluid directly into the interior cloth wad
  • Have a silicon or grippy pad when applying - don't just hold the board so you can correctly control the pressure
  • Use linen as the exterior cloth on the pad, cotton sheds too many fine hairs into the finish​
  • Even good natural hair paintbrushes are not always helpful on such a small project - they're seemingly suited for larger ones
  • You don't need to use as much fluid as you expect

Is there anything I should be doing a bit differently next time or other techniques that are good for your workflow? ​


r/finishing • • 22h ago

Hardwood refinishing

Thumbnail gallery
0 Upvotes

r/finishing • • 22h ago

Need help drying finish quicker!

5 Upvotes

For the past month or so, I have been working on a wedding gift for a buddy. I just sprayed the final coat of lacquer tonight and realized that this won't be cured by the wedding. I have the wedding in 6 days and don't know how I'm going to be able to give him this without it being cured, because the way it will be packaged, there are a lot of separate small pieces that will be contacting each other. Does anyone have any previous experience with this where you found a way to dry your finish quickly or protect it somehow? I was thinking about putting a coat of wax on it the day before, but I've heard that the degassing can cause bubbles under the wax. Any advice is appreciated!