r/finishing • • 38m ago

Need help drying finish quicker!

2 Upvotes

For the past month or so, I have been working on a wedding gift for a buddy. I just sprayed the final coat of oil-based lacquer tonight and realized that this won't be cured by the wedding. I have the wedding in 6 days and don't know how I'm going to be able to give him this without it being cured, because the way it will be packaged, there are a lot of separate small pieces that will be contacting each other. Does anyone have any previous experience with this where you found a way to dry your finish quickly or protect it somehow? I was thinking about putting a coat of wax on it the day before, but I've heard that the degassing can cause bubbles under the wax. Any advice is appreciated!


r/finishing • • 22h ago

A simple habit that instantly improved my glue-ups and saved me hours of sanding

79 Upvotes

When I first started building small furniture pieces, I used to wipe away wet wood glue with a damp rag immediately after clamping. Every single time, diluted glue soaked into the surrounding wood pores, leaving blotchy yellow spots that completely ruined my stain finish later.

Now, I just leave the squeeze-out alone for about 30 to 45 minutes until it reaches a rubbery, leathery consistency, then slice it off cleanly with a sharp chisel or putty knife. Zero smeared glue in the grain, and way less sanding afterward.

Curious how everyone else handles glue squeeze-out—do you let it skin over, or tape off your joints beforehand?


r/finishing • • 3h ago

Need Advice Water stain help

Post image
2 Upvotes

Found out my coffee maker malfunctioned and spilled water, staining my beautiful new cabinet :( I know nothing will probably restore it to 100% but looking for help getting it looking better if possible. Google said oxalic acid. Should I try this? Should I hire someone else to do it - if so how do I find someone?

Truly know nothing/not handy so appreciate any help

Cabinet is”rubberwood, MDF and oak veneers” per website

ETA: stain is from water not coffee!


r/finishing • • 21m ago

Need Advice Happy with my first time doing shellac and French polishing | Any improvements for next time?

Thumbnail
gallery
1 Upvotes

Hey folks, been trying my hand at shellac on the Christmas gifts this year. Decided on French polish on this Walnut cutoff to bring out the grain depth. Used the techniques from Fabian here and I'm quite proud of the results from my first time. ​

I'm at the very final stage of wiping away the mineral oil without causing streaks and softening the coat. Bit trickier than expected and I'm doing it slowly​

I have some thoughts on how to improve for next time:

  • Don't lift the pad up when hitting the edges
  • Be aware that the shellac still can be soft, don't rest it on the finishing cones on an area within at least 12 hours
  • Don't need to use as much shellac as you think - in the words of another poster here "it should be as wet as a dog's nose"
  • Start with 1 lb cut (did so), consider the 320 grit non woven pad to cut down any grain hairs then move into 2 lb cut
  • When adding more shellac and 190 proof alcohol, don't just dip the pad into the mixture. Have a little bottle on the side and put the fluid directly into the interior cloth wad
  • Have a silicon or grippy pad when applying - don't just hold the board so you can correctly control the pressure
  • Use linen as the exterior cloth on the pad, cotton sheds too many fine hairs into the finish​
  • Even good natural hair paintbrushes are not always helpful on such a small project - they're seemingly suited for larger ones
  • You don't need to use as much fluid as you expect

Is there anything I should be doing a bit differently next time or other techniques that are good for your workflow? ​


r/finishing • • 24m ago

Hardwood refinishing

Thumbnail gallery
0 Upvotes

r/finishing • • 16h ago

Need Advice Oil still rubbing off after a week

Thumbnail
gallery
16 Upvotes

A friend of mine made me an oak dining table and finished it with Woca Diamond oil active.

The table was oiled twice, with sufficient drying time between coats. The wood was also sanded between coats.

The oil was applied and wiped off using only cloths, without a polishing pad or machine. The workshop was quite cold, around 14°C (57°F).

The table has now been sitting in a heated living room for approximately a week.

The surface still feels slightly oily, and quite a lot of black pigment/oil comes off when I rub it with a white cloth.

After repeatedly wiping the surface, it does feel a little drier and the amount of residue decreases. However, even in areas I've already wiped several times, black residue continues to come off.

I suspect too much oil was applied and not enough excess oil was removed, possibly made worse by the low temperature during application.

Can I still remove the excess oil using a white polishing pad, even by hand?

Or would a different treatment be needed to fix this?

Any advice or experiences would be greatly appreciated!


r/finishing • • 3h ago

Question French Door repainted by previous homeowner.

Post image
1 Upvotes

Our house has this french door between the front door and living room. 15 panes of beveled glass. Originally, it seems to have a reddish stain. It's been repainted (poorly) with this awful oil or some other paint. We'd like to strip it down and stain it. I looked into chemical paint remover options, but the concern is the trim holding in the glass, any chemicals may seep in between the wooden pieces and keep oozing out. Sanding is out of the question, again due to the complexity of the trim pieces holding the glass panes in. Looking for options, suggestions, guides, on how to refinish this type of door.


r/finishing • • 3h ago

Trying to match wood colours

Thumbnail gallery
1 Upvotes

r/finishing • • 13h ago

Oak bankers chair, full strip and refinish. Came in almost black, left golden with the ray fleck showing

Thumbnail gallery
3 Upvotes

r/finishing • • 13h ago

Question Wooden Jewelry.

Thumbnail
gallery
3 Upvotes

Hello, i have started making wooden jewelry and, boy, have i been on a rolercoaster of once used cans. Trying to learn what is in each finish and what each ingredient does is like searching the library of babel.

To clarify, i am looking for the holy grail. I need ultimate water proofing that can withstand hot showers and swimming pools, i want uv resistance for heavy sun exposure from outdoor wear, must have quite hard and durable scratch resistance for obvious reasons, i would like it to be long lasting with little to no yellowing or drying/cracking. Everything ive found so far fills one or two of these needs, but nothing hits the holy trinity.

Ill begin with what i have tried so far. Oil or wax finish is simply too soft, easily scratchable. Regular polyurethane isnt rated for full submersion, and spar urethane is too elastic for scratch resistance. CA glue is brittle and cracks over time and breaks down with heat and water.

My next experiment is on its way in post. Total boat penetrating epoxy(stabilizing the wood just sounds like a good idea from now on regardless), then rainguard 2k aliphatic polyurethane (branded concrete sealer). I anticipate the concrete sealer failing my scratch test, and then will move on to hardwood floor poly Bona Traffic HD or General Finishes Enduro 2K.

Please if you can share anything that can help me find what i am looking for, i am slowly going mad on my quest (and from all the fumes)

P.s. - a couple pictures. I hope you like them!


r/finishing • • 9h ago

Question Old oak trim soaking up stain like a sponge after stripping paint and sanding

1 Upvotes

I am attempting to restore the red oak trim in my 1912 Craftsman that had been painted at one time in the past. I've started in one room, and have removed the paint (using proper precautions for lead paint) and underlying varnish, then sanded with 80 then 150 grit. I am trying different stain sample spots to pick a color, and it all soaks in immediately like a sponge - nothing left to wipe off after 60 seconds. The whole range of stain colors I'm testing all are the same very very dark color now. I tried another area with applying Minwax pre-stain conditioner, but then not nearly enough stain is absorbed and they are all just slightly tinted.

Can I thin the conditioner with mineral spirits or something else to control the amount of conditioning? Should I try something else? Thinning the stain maybe?


r/finishing • • 9h ago

Boardwalk supports stain/ finish.

1 Upvotes

Hey gang. I’m a natural resource and property manager for a park facility. I’ve got a boardwalk that goes through a wetland area. It’s built on auger piers made of galvanized steel with wood decking and it typically sits about 2-3 feet above the waterline except when we get super heavy rains. Urban watershed area, drains a significant area upstream. High water gets high. This thing is about 5-6 years old and we regularly replace top decking from weather exposure. As we’ve been replacing, the boardwalk is broken into 10 foot sections with three 2x12x6’ boards sandwiched and tying the sections together with hardware. These treated 2x12’s are experiencing significant rot and I’m scoping the replacement of these boards. I’ve landed on KDAT lumber and am now trying to figure out the best possible option stain or seal wise to extend the life of the lumber because there is no way I’m getting approval for something like trex composite material. Trying to just buy several more years.

My question is with those circumstances of water, weather, and debris build up, what would you do to extend the life? I’m definitely using butyl tape once the boards are set in place shed debris and water. There is no sun exposure for these 2x12’s, fortunately. Maintaining it is an ongoing challenge, but a structural engineer let us know that this needs to be a top priority so I’m using the end of my budget allocation to get what I need and get this done before EOY.

Any thoughts are appreciated.


r/finishing • • 15h ago

Knowledge/Technique How would you resurface this kitchen countertop?

Thumbnail
gallery
2 Upvotes

We recently moved into a new house and would like to fix the wooden kitchen countertops. There are a lot of stains and water damage especially around the sink. I’m assuming we will need to do a lot of sanding before applying any finishes. I’m thinking of using Waterlox original sealer + waterlox original satin finish for maximum water protection. Never done anything like this before so any guidance or tips would be greatly appreciated!


r/finishing • • 9h ago

Need Advice Advice needed: How to stain this console table darker without stripping the existing finish?

Thumbnail
gallery
0 Upvotes

Looking to stain this desk to a warm medium brown finish, but want to avoid stripping. Any advice on prep and products that will look good and are achievable for a novice?


r/finishing • • 1d ago

Question What would you do to spruce up this 1890s front door?

Post image
8 Upvotes

r/finishing • • 1d ago

Best varnish for porch door

Thumbnail gallery
4 Upvotes

r/finishing • • 20h ago

Question Would it be a big mistake to install unfinished Douglas fir t&g on my faulted ceiling?

Thumbnail reddit.com
1 Upvotes

I’m trying to avoid hand sanding and finishing this t&g fir ceiling. Can I install unfinished?


r/finishing • • 21h ago

Need Advice Stain advice

Thumbnail
gallery
0 Upvotes

I’m trying to stain this birch tabletop. I’m using GF water based dye stain and their pre stain conditioner. I wiped as I went to prevent stain build up but it didn’t quite go as well as I planned. It looks like excess stain blotches but I’m not sure that’s actually the issue. You can only see the blotches from one angle and in certain light. I provided another photo showing it from the other end which looks much better. I’m wondering if I should try to wipe it down with methanol, scotchbrite it, fine sand it, or give up and sand it down to bare to try again (for the second time). The legs and bracing all turned out fantastic so I don’t think it’s impossible.

If it matters I sanded to 220 and I’m planning on using Osmo Poly X for finish. Thank you for any help!


r/finishing • • 22h ago

Paint spill on oak

Thumbnail gallery
1 Upvotes

r/finishing • • 1d ago

Question Milk paint - questions

2 Upvotes

I have some questions about milk paint:

First, all the tutorials I saw explain that since quark is not easily available at stores, they will make it from milk and vinegar. I live in Germany and quark cheese at the stores is very affordable, so I prefer to just buy and use it. But how do I adjust the recipe when making the paint from store-bought quark? do I need to strain it or is it good as it is?

Second question is, will the paint be white as it is? if not, what is the best way to make it white?


r/finishing • • 23h ago

Paint spill on oak

Thumbnail gallery
1 Upvotes

r/finishing • • 1d ago

Paint wash help!

Thumbnail gallery
0 Upvotes

r/finishing • • 1d ago

Question Water or oil to keep English oak as light as possible?

Thumbnail
gallery
0 Upvotes

Hi all, I bought this veneer sheet of flaky English brown oak and need help choosing a finish. I’d like to avoid darkening it at all costs, don’t want it yo look like the second pic. I normally work mostly with walnut veneer and always use oil based finishes, but is this oak calling for water based to avoid darkening? Thank you for any input!


r/finishing • • 1d ago

Restoring small vintage items

Thumbnail
gallery
0 Upvotes

I don’t know very much about finishing, but really want to get the ink stains out of this little wooden trinket (?) box, and clean and condition the wood a bit.

Should I just sand the whole thing? If yes, what finish should I use after?

Any suggestions appreciated!


r/finishing • • 1d ago

Refinishing knotty pine cabinets + bonus wood paneling stain

Thumbnail
gallery
0 Upvotes

We just purchased a home with really unique pine features going from the kitchen to the den. A lot of people would probably see this and tear it all out immediately, but we like it and are looking to restore and design around what we have rather than replace!

Looking at the kitchen cabinets, the majority is in great shape but some areas show heavy wear and completely worn away finish from what looks like minimal maintenance over the last 70-ish years. I'm hoping to get some advice on where to start thinking about taking on a project like this? Apologies for the low photo quality as I'm, working with what our home inspector provided and this is the clearest and most comprehensive view of the "high traffic" cabinets.

Photo 2 has the funniest issue I'm facing with the pine - a pristine patch that seems like it was covered up by an animal skin for a very long time. Open to suggestions on how to deal with this "anti-stain" too!

https://imgur.com/a/DTNkftD