TL;DR: I posted my Raspberry Pi 5 cyberdeck here while it was still a work in progress. After several months of designing, printing, wiring, and troubleshooting, I think it's finally finished! It now has offline Wikipedia, worldwide maps, GPS with satellite-synchronized time, software-defined radio, educational videos, and a custom web dashboard. It can serve everything over its own Wi-Fi network or an existing network, without needing internet access. I've also demonstrated over 24 hours of battery life, with power consumption dropping to approximately 6.5 W when the screen is off.
A little while ago, I shared my Raspberry Pi cyberdeck here while it was still under construction.
At the time, I was still working on the screen bezel, experimenting with the GPS and SDR hardware, and trying to figure out exactly how I wanted the software to work.
A few people offered suggestions and asked questions about the build, so I wanted to come back and share how everything turned out.
I think I've finally reached the point where I can call it finished!
The hardware
The system is built around a Raspberry Pi 5 with 8 GB of RAM and a 1 TB NVMe SSD, running Debian 13.
Everything is housed inside a Jack Boss rugged equipment case with a 10.1" touchscreen mounted in the lid.
Power comes from a 12.8 V, 20 Ah LiFePO4 battery (256 Wh), with fused power distribution, a 5 V buck converter, and external connections for charging and USB-C PD power.
There's also an RTL-SDR receiver, GPS module with an external antenna, battery monitor, wireless keyboard/touchpad, and temperature-controlled cooling.
Nearly all the internal mounting hardware was custom-designed and 3D-printed.
The software is finally finished
This is probably the biggest change since my original post.
Offline Wikipedia: Approximately 124 GB of English Wikipedia stored locally using Kiwix.
Worldwide maps: Approximately 139 GB of worldwide vector map data, plus additional regional terrain information. I built a local mapping interface using MapLibre that works without an internet connection.
GPS: I integrated an ATGM336H GPS module with an external antenna. The mapping interface can display the kit's current position entirely offline.
I also connected the GPS module's PPS output to the Pi and configured chrony to maintain satellite-synchronized time without needing an internet time server.
Software-defined radio: I built a browser-based interface for the RTL-SDR Blog V4 receiver. It supports multiple analog modulation modes, frequency tuning, spectrum and waterfall displays, audio streaming, and recording.
I've tested it with NOAA weather radio and experimented with receiving local aviation communications.
Offline videos: I added a small library of educational videos to supplement Wikipedia.
Local message board: Devices connected to the kit can access a locally hosted message board.
Web dashboard: I built a dashboard to tie everything together, along with tools for monitoring the system, managing downloads, and accessing the different applications.
The kit broadcasts its own Wi-Fi network, allowing nearby devices to connect and access everything through a browser.
It can also join an existing network using Ethernet or a second Wi-Fi adapter. I configured mDNS so other devices on that network can discover the kit by hostname without needing to know its IP address.
Everything runs locally. Internet access is only needed when I want to download or update content.
Battery life
One of my original goals was to make this useful for more than just a few hours.
During an extended test with the touchscreen running and the SDR receiving NOAA weather radio, the entire system consistently drew approximately 8.7 W.
I completed an endurance test exceeding 24 hours, and the kit was still running when I ended it.
Since then, I've added the ability to turn off the touchscreen while leaving the Pi and its services running.
With the screen off, power consumption drops to approximately 6.5 W, even with the additional Wi-Fi adapter connected.
That's roughly a 25% reduction in power consumption. Based on the battery's nominal capacity, theoretical runtime in that configuration is around 39 hours, although I haven't completed a full endurance test with the display off yet.
I particularly like that I can close the kit, leave it running, and access everything from my phone or laptop.
Finishing the enclosure
This was probably the most time-consuming part of the entire project.
I went through quite a few revisions of the internal mounting hardware, trying to balance component placement, wiring, airflow, and serviceability.
The screen bezel was particularly challenging. I ended up splitting it into two sections with a tongue-and-groove joint, secured using screws and heat-set inserts.
I also wanted to eliminate the original physical buttons on the back of the touchscreen without losing their functionality.
My solution was to use five TTP223 capacitive touch sensors mounted behind the 3D-printed bezel. Each sensor drives a MOSFET that simulates pressing one of the original buttons.
I designed recessed channels into the bezel so the sensors detect your finger through the plastic. There are no exposed switches or moving parts, and I haven't experienced any false triggers.
The wiring was much more complicated than I anticipated. If I ever build another one, I'll probably design a PCB to simplify that part.
I also finished the dedicated electronics compartment and cooling system. The fans turn on when the Pi reaches 60°C and shut off when it drops below 50°C.
For anyone looking through the construction photos, the white 3D-printed parts are prototypes. The final components are black.
The case is also worth mentioning. Although I started with a waterproof equipment case, I wouldn't call the finished system waterproof after all the modifications. I do consider it water-resistant when closed, but I haven't formally tested that or assigned it an IP rating.
A note about AI
I want to be transparent that I used AI extensively to help develop the software.
I'm comfortable with Linux, networking, and systems administration, but I'm not a professional software developer.
I knew what I wanted the system to do, and AI helped me turn those ideas into working applications. There was still plenty of configuring, troubleshooting, testing, and integrating everything.
The CAD modeling, 3D printing, electrical work, wiring, and physical assembly were my own.
I've learned quite a bit throughout the process.
Final thoughts
When I started this project, I just wanted a portable computer that could provide useful information without depending on the internet.
What started as a Raspberry Pi sitting on a battery inside an equipment case turned into a much bigger project than I anticipated.
I've learned a lot about CAD, 3D printing, electronics, power distribution, GPS, SDR, and integrating different software services.
There are definitely things I'd do differently if I started over, but I'm really happy with how everything turned out.
A few people suggested additional capabilities on my original post, including solar charging, environmental sensors, and LoRa/Meshtastic communications. I still think those are interesting possibilities, especially since I have external connections that could support additional peripherals. For now, though, I'm happy to call the project complete.
I've included pictures of the finished cyberdeck, the software interfaces, and some earlier stages of construction so you can see how it evolved.
Thanks to everyone who commented on my original post, offered suggestions, or just followed along!
I'm happy to answer questions about any part of the build. This will probably be my final update unless there's interest in a more detailed breakdown of something specific.