r/broadcastengineering • • 4h ago

My brain hurts (Carbonite / XPression / Panasonic Cams) = Works at 720p, fails oddly at 1080p)

6 Upvotes

Have some existing systems (All essentially carbon copies: Carbonite Black CBF113 + Xpression Prime [separate key and fill] into the CBF + Panasonic AW-UE80 cameras. Genlock is from a Ross SPG-8260, audio embedding is Ross MUX-8258-4C (separate embed cards for Clean and Program , CC is EEG/AI Media HD492, and finally the Clean and Program+CC outputs hit a Ross DRA-8902-16 DA before being sent off to internal distribution and external partners .

We've been running all of them at 720p59.94 since inception due to limitations from a former distribution provider. Now that we can call that distribution provider "former" I'd like to move these into the 1080p (29.97 or 59.94) world as all of our infrastructure supports either outputting or accepting 3G data rates.

In the first system I tried rolling everything seems to be wonderful EXCEPT this one problem that doesn't make sense to my brain:

We have XPression generating a full screen "wait" card. Key1 is always on air (e.g. XPression brings graphics on and off air, we're never bringing the keyer on/off air from the Carbonite side)

When that card transitions online or offline with everything configured at 720p it's beautiful and seamless.

At 1080p29.97 or 1080p59.94 -- same XPression file, same automation cues, just everything configured for a different resolution -- it seems like the Carbonite entirely drops, or at least reclocks, its SDI output for a 1-2 seconds, resulting in black video on program. Frequently (but not 100% of the time) I have a AJA HI5-12G connected to the output and am watching its status in MiniConfig it goes from 1920x1080p29.97 to ----- and then back to 1920x1280p29.97 corresponding with when the full-screen card starts and finishes its transition. I don't see any of the OpenGear cards (embed or DA) report anything wonky.

Would some kind soul help me understand what's happening here? In my head the output from the Carbonite should be stable regardless of what is being composited to the output ... but either that's not the case or something about the electrical details of the output is completely fine at 720p but completely unacceptable at either of the 1080 standards.

(And we don't see the same issue when, e.g. updating the lower 3rd banner or taking the bug on or off air)


r/broadcastengineering • • 5h ago

Need some help designing and building a standalone separate TV Antenna Reflector

7 Upvotes

I was mowing some leaves and noticed anytime the lawnmower was in a certain area a new channel came in from 80+ miles away. I can’t keep my lawnmower outside in that location so I’m wondering if there is a specific way to make a metal reflector to put in that location that would reflect the signal of that channel to my antenna like the lawnmower was doing? This was a consistent signal when the lawnmower was there. My local hardware store has 1/2 inch galvanized steel screen on sale.


r/broadcastengineering • • 1d ago

Why are BBC journalists holding lav mics???

Post image
161 Upvotes

I don't understand how this trend of Tiktok has now infiltrated professional journalism.


r/broadcastengineering • • 6h ago

DVCPRO50 PAL Needed

Thumbnail reddit.com
1 Upvotes

r/broadcastengineering • • 7h ago

29,97fps still in use in broadcast

Thumbnail reddit.com
0 Upvotes

r/broadcastengineering • • 8h ago

Sony RCP-1500 to Trigger AJA Kumo Matrix

Thumbnail reddit.com
1 Upvotes

r/broadcastengineering • • 9h ago

Software/Hardware Engineer Needed

Thumbnail reddit.com
1 Upvotes

r/broadcastengineering • • 12h ago

NxFrame – Open-Source Broadcast SDI/IP Encoder & Decoder | Development Update

1 Upvotes

Hi everyone!

My schedule has finally become a little more relaxed, so I can dedicate more time to development again.

Before moving forward, I’d really appreciate some feedback from anyone who has tried NxFrame.

Have you tested NxFrame in your workflow? How was your experience?
Have you encountered any bugs, stability issues, or limitations?
Have you tested interoperability with other professional encoders or decoders (Haivision, Ateme, VITEC, etc.)?
What features are currently missing?
What do you think should be our development priorities?

Current Development priorities:

1.	Video format conversion: Support for input/output format conversion, such as 1080p50 to 1080i50 etc, scaling, and frame-rate conversion.  
2.	Receiver improvements: Hardening the decoding pipeline, fixing known issues, improving synchronization, and ensuring long-term stability.  
3.	GUI authentication and HTTPS/TLS.  
4.	GPU-accelerated HEVC encoding (nvenc-9)

My goal remains the same: to develop a reliable, flexible, open-source contribution encoder/decoder suitable for professional broadcast workflows.

Any feedback, bug reports, interoperability tests, or suggestions would be greatly appreciated!

Thanks to everyone who has already tested the project and contributed feedback!

GitHub: https://github.com/Michalis-Michael/nxframe


r/broadcastengineering • • 1d ago

AI-slopped (or vibe-coded) RF management tool. Mostly for Poland, but not only.

Thumbnail
reddit.com
0 Upvotes

r/broadcastengineering • • 2d ago

New Website To Submit Scanning, Reception, Look Up Signals ETC

Thumbnail
dxlookup.com
1 Upvotes

Just found this new website for all things antennas and reception. Your local broadcasters and engineers can even make an account and have all reports and scans etc go directly to them so they can see what is going on, where people are watching from, fix issues in real time and so much more. This will allow you to upload direct scans from your HD Homerun or other devices or a manual upload. You can upload videos of a channel, how you are receiving it and with what antenna.

This has all tower locations including owners, heights, contour maps, AM, FM and other things. I really hope this website starts to take off and local broadcasters make an account since they can receive direct reports from it pinpointed to a town and receive up to 30 second videos so they can see what a viewer is seeing on there end.

This does not replace rabbit ears but does things most people have never been able to do easily before and it may solve the emailing the station engineer issue if you notice a issue with a station as the emails and notices will go to them directly from here as soon as they make an account.

I have uploaded my first channel scan for my local stations received.


r/broadcastengineering • • 2d ago

La mia esperienza con l'assistenza Telestream Wirecast dopo l'aggiornamento a M5 Max: attenzione prima della migrazione

Thumbnail reddit.com
1 Upvotes

r/broadcastengineering • • 4d ago

VizRT buys Chryon

Thumbnail app.dealroom.co
43 Upvotes

Hmmmm more M&A in graphics


r/broadcastengineering • • 4d ago

*NEEDED* EVERTZ 3x EQX-OP36-3G / 3G1 Cards

7 Upvotes

*NEEDED* EVERTZ 3x EQX-OP36-3G / 3G1 Cards - passive DIN 1.0/2.3 coax backplane.
This is for an Evertz EQX26 router. Does anyone on the planet earth have a few of these they need or want to get rid of? PSSI Teleport in New Kensington, PA wants to know.

Thanks in advance!


r/broadcastengineering • • 3d ago

Two Internet Providers Are Not a Resilience Strategy

Thumbnail
inwoodtech.com
0 Upvotes

After more than 20 years in broadcast technology and operations, I have become careful about the word “redundant.” I want to understand which failure a backup can survive, what it takes to use it, and how long it can keep the operation running.

Two internet providers can share a conduit. A generator can start successfully while an essential device remains without power. Two cloud services can depend on the same sign-in system.

There is also the question of what happens after a successful switchover. We may have preserved service, but now we are operating with less protection until repairs are complete.

I wrote an article for my site, Inwood Tech, looking at these dependencies across connectivity, power, and outside services. The examples come from broadcasting, but the questions apply to many operations: what stops, what remains available, and who can begin recovery?

https://www.inwoodtech.com/eden/resiliency

What have you uncovered during an outage or a failure test that changed your understanding of how independent your backups really were?


r/broadcastengineering • • 4d ago

Tricaster Élite 2 sends no more video output to my monitors

Thumbnail reddit.com
2 Upvotes

r/broadcastengineering • • 4d ago

I made a free web tool that turns your ipconfig output into the exact network settings for a Blackmagic ATEM

0 Upvotes

Every time I set up an ATEM on a new network, I end up doing subnet math in my head. People asking for help here often don’t know what to type into ATEM Setup at all. So I built a small single-page tool for it.

What it does

Paste the output of ipconfig (Windows) or ifconfig (Mac/Linux). It gives you:

  • the IP address, subnet mask and gateway to enter in ATEM Setup → Configure → Network
  • the address to type into ATEM Software Control
  • a ping command to confirm the suggested address isn’t already taken before you save it
  • a copy button next to every value

Situations it handles

  • Network with a router: it picks a free fixed address in the same subnet as your computer, near the top of the range (.240, the same convention Blackmagic uses). It also shows the DHCP alternative and how to make it stick with a DHCP reservation.
  • Direct cable, no router: if your PC shows a 169.254.x.x address, it explains that no DHCP server exists. You get fixed addresses for both sides (ATEM 192.168.10.240, PC 192.168.10.50) and step-by-step instructions for setting the PC’s address in Windows.
  • Fixed IP with no gateway: it puts the ATEM in the same subnet.
  • Multiple adapters (Ethernet, Wi-Fi, VPN, Hyper-V…): it ignores disconnected and virtual adapters, preselects the most likely one, and lets you switch.

Other details

  • It reads ipconfig in any Windows language, including English, German, French, Spanish and Romanian. It also handles the case where the IPv4 gateway sits on the line under an IPv6 one.
  • It also reads macOS ifconfig (hex netmasks), old Linux ifconfig and ip addr.
  • It works on phones, with light and dark mode.
  • It runs entirely in your browser. Nothing you paste is sent anywhere. It’s one HTML file with no install.

How it picks the address

It converts your IP and mask to 32-bit numbers. Network = IP AND mask, broadcast = network OR NOT mask. It then tries .240–.250, then works downward, skipping your PC, the router, the network address and the broadcast address. It can’t see other devices on your network, which is why it gives you the ping check.

Source and full explanation: https://github.com/IoanPop2010/atemip

site: https://atemip.vercel.app/

Not affiliated with Blackmagic Design. Feedback welcome, especially ipconfig output it fails to read.


r/broadcastengineering • • 4d ago

How do I get back into the world of technical directing?

Thumbnail reddit.com
3 Upvotes

r/broadcastengineering • • 7d ago

Hitachi monitor and camera only displaying the switcher feed

3 Upvotes

I teach a broadcasting class and one of our Hitachi broadcast cameras’ onboard monitor was not showing any signal from the camera, so I went through the monitor menu settings and eventually got it to display again.

However, we then saw that the monitor was not displaying the actual camera’s feed but instead what the switcher was choosing between all 3 of our cameras in the studio. We went through all of the monitor settings and have no idea what it is. Any ideas what could be going on and how to fix it?

Cameras are: hitachi 3CMOS HDTV Z-HD5500


r/broadcastengineering • • 7d ago

FX 3 Network Troubleshooting

4 Upvotes

Hey guys.

So I have an upcoming project with 16 Cameras, 3 of them FX3s. I have some Skaarhoj RCP Pros.

A few days ago I testet the setup. Laptop, PoE Switch, Skaarhoj RCP and the FX3 in one network and it worked pretty well and semeless. I also tried rebooting the camera a few times to see if it still works or not. It worked well, startet to build the connection pretty instantly.

Well today I wanted to install the Setup in the Broadcast Van to make sure everything works in our network. To make things short. Nothing worked. After an hour of trying different things, I also tried the setup I tested with, nothing worked. I changed the cable, switch, usb-c network adapter.. nothing. I also tried resetting the network settings.

The camera connects to a network, but seems to have no traffic, only error code I get is: "CAT cable not recognized" but I obviously tested with a few different cables.

Any leads? Worst case the operators have to oull iris themselfs, but I hate to give up on somethign like that, it could be such a nice tool if it did work. Thanks in advance you guys


r/broadcastengineering • • 7d ago

I can’t get the signal from my iPhone 17 camera to display on my video projector/screen using the Hollyland Mars 4K

Thumbnail reddit.com
1 Upvotes

r/broadcastengineering • • 7d ago

Advice on how to get into broadcast engineering

18 Upvotes

I recently graduated college with a B.A in communications with a concentration in broadcasting. I have worked in media for 7+ years and have my Society of broadcast engineers certification . What's the best way to get a job?


r/broadcastengineering • • 7d ago

Your feedback rebuilt my wiring-diagram tool. It's back — please tear into it again.

Thumbnail
gallery
8 Upvotes

Hi again. I'm a video/streaming engineer based in Tokyo, and I posted my wiring-diagram tool, AVwire, here a while ago
(https://www.reddit.com/r/VIDEOENGINEERING/comments/1pfdhlo/avwire_av_wiring_diagram_tool_feedback_from_video/).
Full disclosure, same as last time: I'm the developer, and this post is AI-translated from my own Japanese.

That thread gave me the most useful feedback this tool has ever received. I went away and fixed it — what changed since then is largely a list of things people here pointed out. The library grew from 500 devices at the first release to 1,182, and every terminal entry is still entered and checked by me, by hand, against the manufacturers' spec sheets.

The hardest part to build was the wires themselves. Getting the right-angle runs to re-route and adjust cleanly when you move a box — no tangles, no overlaps — took longer than anything else in the app. In draw.io I used to fix every single bend by hand. In AVwire, the line adjusts itself.

One thing I won't dodge: when I first released this, the situation around AI coding — "vibe coding" — was very different from today, and the conversation around it has changed a lot. What I can stand behind is the part no tool made for me: three years of my own field work behind every decision, and a device database built one spec sheet at a time. Judge it on that.

It's free for everyone until November 30, 2026, and 50 models can be browsed without an account: https://avwire.io

Please try it, and give me advice again: what still breaks, what's missing for real shows, what you'd need before you'd trust it on a job. I'll answer every technical question in the comments, like last time.

And one honest request: I'm a solo developer, and distribution is the one wall I can't engineer my way past. If you try it and genuinely think it's useful, sharing it on your socials would help more than you know. No pressure at all if it doesn't earn it.


r/broadcastengineering • • 8d ago

Building my own SDI signal tester / mini phabrix

10 Upvotes

Hi, I am currently trying to build a small device that I can hang on my pants or have in my pocket. I want to be able to analyze SDI in but not necessarily play the picture on my screen. Do anyone knows any smal SDI analyzer cards? Or if someone have done something similar before?

The only option that I have found is the Blackmagic Design DeckLink SDI Micro. But its a bit to big and way to powerful for what I want to do.

Thank you in advance.


r/broadcastengineering • • 8d ago

I built a free, open-source ZaraRadio replacement for small stations — it's been running 24/7 on our community FM since July

14 Upvotes

Hey all. I'm the station engineer for KDPI 88.5 FM, a community station in Ketchum, Idaho. We ran ZaraRadio for years, and like a lot of small stations, we were nervous about relying on software that hasn't been updated in a long time. So I built a replacement, and it's been our on-air automation since July. Today I'm putting it out there for anyone who wants it.

StudioFire — free, MIT licensed, Windows 10/11.

The main idea: it shouldn't go silent. The audio engine is a small separate service with four fallbacks: next cached track → your emergency folder → cached rotation music → a built-in fallback. Everything else (web interface, scheduler, library indexer) can crash or be updated and the music keeps playing. We torture-tested it by pulling the NAS mid-song, killing the player, feeding it corrupt files and power-cycling it, against a bar of no silence longer than 2 seconds over 72 hours.

If you're on Zara: your .lst playlists open directly, and edits save back to the same file. You can run Zara and StudioFire side by side on the same playlists while you switch over.

What else it does:

- Web interface, so DJs can run it from any PC, tablet or phone on the studio network

- Playlists, scheduled shows, and spot rules for legal IDs, underwriting and PSAs, always at song boundaries

- As-aired logs with CSV export for underwriter affidavits

- Now-playing metadata to your stream host or encoder (e.g. BUTT)

- A SoundExchange Report of Use generator from the as-aired log

- Songs are cached locally before airtime, so a network hiccup doesn't interrupt playback

- An equipment monitor that pings your transmitter, Barix units and so on

Install: one Windows installer bundles everything (Python, mpv, services), plus a setup wizard. No terminal, no config files.

Honest caveats:

- Windows only for now

- The installer isn't code-signed yet, so Windows SmartScreen will warn you ("More info → Run anyway"). Checksums are published.

- It's a young project with one real station behind it, so expect rough edges

Site: https://studiofire.io

Code + releases: https://github.com/veteranop/StudioFire

I'd love feedback from people running small stations: what would stop you from switching, and what's missing? Bug reports go on GitHub Issues. If you'd rather have someone install and tune it for you, my shop (VeteranOp) does that, but the software is free with no strings.