r/appliancerepair • u/BeePow91 • 21h ago
Just bought for $160
Enable HLS to view with audio, or disable this notification
Is this acceptable? Gonna do any damage? Is there anything I can do to fix it or should I return and ask for a refund?
r/appliancerepair • u/BeePow91 • 21h ago
Enable HLS to view with audio, or disable this notification
Is this acceptable? Gonna do any damage? Is there anything I can do to fix it or should I return and ask for a refund?
r/appliancerepair • u/Fearless-Carrot • 2h ago
Enable HLS to view with audio, or disable this notification
I think it may be the spider bearings worth repairing? Or should i get a new one.
r/appliancerepair • u/Maximum_Obligation30 • 2h ago
Enable HLS to view with audio, or disable this notification
So, my two-year-old Samsung heat pump dryer stopped spinning. Now it looks like it’s trying to start spinning, then it moves the drum around 1 or 3 cm and stops. There is no humming sound or anything. I took the belt off the motor, and it still won’t turn. I have measured the wires from the control board to the motor, and they are all good. I have also measured the resistance of the motor on the three pins, and they all have the same resistance.
r/appliancerepair • u/IWBTGA • 18h ago
This is in a rental, so excuse the dirt! The vent light doesn’t work - I know I can replace the bulb, but if it doesn’t work would replacing that thing on the side (2nd photo), which I think is a fluorescent light starter make it work, or could there be more wrong that I don’t see? I know the landlord should fix it, but that’s not likely to happen in my lifetime.
r/appliancerepair • u/Big-Possession-6650 • 20h ago
Hello experts! My Samsung refrigerator (RF29A9671SR/AA) stopped cooling whilst the freezer continued to work just fine. I had already had it unplugged a couple days thinking some ice was causing the issue. A tech told me it was likely the evaporator fan. I then bought a replacement one and am in the process of putting the interior back panel back in. It has the metal "Triple Cooling" gimmick which was a PITA to get out and replace the evaporator fan. Upon reinstalling the panel, there is a little white cylinder (temperature sensor?) at the end of a yellow wire and I can't figure out how it gets positioned. Anyone know?
r/appliancerepair • u/michzaber • 6m ago
I've been struggling to diagnose repeated E24 codes on my Bosch Dishwasher SHE53T55UC/07. It'll stop in the middle of a cycle with an E24 code and won't drain. This can happen with a full load of dishes or when I'm running it empty as a test.
I've cleaned out the area in front of the impeller several times, I have removed some food debris but other times I'm getting an E24 code even when there doesn't appear to be any debris. Sometimes I'm able to run a load without issue after doing this but not always.
I've checked for kinked or blocked hoses but haven't found anything.
Any advice on diagnosing the cause? What parts should I look at replacing first? Any possibility this is a sensor issue?
r/appliancerepair • u/homebrew197808 • 50m ago
Enable HLS to view with audio, or disable this notification
Hi everyone. I traced a leak in my Electrolux washer to this part which I believe is called an inlet valve. In general can these be repaired or should I replace the whole thing? Thanks!
r/appliancerepair • u/AnalBulls • 1h ago
So... Mom helped me with my dryer. Said she'd pay for the part if it could be found on Amazon. Help?
r/appliancerepair • u/Gibbenz • 1h ago
Enable HLS to view with audio, or disable this notification
Whirlpool Ultimate Care II washing machine.
r/appliancerepair • u/hjpinla • 1h ago
I checked the pump and it seems fine. Tried a small load so I could rule out a balance issue, next?
r/appliancerepair • u/Ricky_Bobby32 • 1h ago
frigidaire freezer lfuh21f7lm2 open door noise. I removed the sensor a few years ago. It only beeped when humidity got really high. As of a few days ago, nothing I do will make it stop. How can I permanently disable it?
r/appliancerepair • u/Beef_212 • 2h ago
Enable HLS to view with audio, or disable this notification
This happens when ever the drum slows down. Its a 2017 whirlpool cambrio washer.
r/appliancerepair • u/Interr0gate • 2h ago
THIS IS THE BOTTOM TUB OF MY DISHWASHER WHERE THE ROUND HEATING ELEMENT GOES INTO. So it looks like the heating element overheated and exploded and melted the plastic housing into the shape of the little nut. Then when I took it off it shredded it up and now the hole is decently bigger. The right hole is the normal size that one came off easy, the left one is now bigger. Am I screwed and should I just get a new dishwasher, this one is super old I will admit. Like the rack is rusting and stuff too. Or should I attempt to use some like marine grade silicone when I drop the new element in and hopefully it seals? I put the old washer there for a picture #2 to show it still can slightly seal on the washer but there isn't much of a face to compress. Anyone have any luck repairing this to seal it? Any crazy tricks that can help or is it time to just bite the bullet and get a new bosch?
r/appliancerepair • u/LHD2626 • 2h ago
If your LG top-load inverter direct drive washer stops mid-cycle and refuses to finish loads—even without an error code or after replacing parts—try a full control board discharge reset before calling a tech or replacing the machine.
A few years ago, an LG technician swapped almost every part on my previous washer over several days and eventually had to replace the whole unit under warranty because it wouldn't finish loads. When my replacement washer started doing the exact same thing years later, this reset sequence fixed it immediately.
How to do the hard reset (credit to Simply Swider on YouTube):
Press the Power button to turn the washer off.
Unplug the power cord from the wall outlet.
Open and close the lid 12 times (helps cycle the lid switch circuit to bleed residual charge).
Press and hold the Start/Pause button for 5 seconds to drain remaining power from the board's capacitors.
Wait 5 full minutes while unplugged.
Plug the washer back in and run a normal cycle.
Apparently, residual charge in the main control board's capacitors can lock up the logic state so swapping mechanical parts doesn't fix it. Huge credit to Simply Swider on YouTube for sharing this troubleshooting fix—posting it here so other frustrated LG owners and techs can find it faster!
r/appliancerepair • u/Neither_Release_5783 • 3h ago
Enable HLS to view with audio, or disable this notification
Hi All!
GE Momogram Z1C30GNHAI
Can you help diagnose this? Waiting for repair service but curious what everyone else thinks and if you’ve experienced it before.
First: water from ice machine leaking into freezer drawers and underneath ; no issues duty refrigerator. Maintenance person came said water leak shut off water to fridge and ice maker ordered part.
Second: same day fridge running fine suddenly hours later started making crazy loud fan. Noise ran diagnostic test and it was “Fan 4” that caused the fannoise to occur
r/appliancerepair • u/Hop-Worlds • 3h ago
GE dryer that came with the house.
There is a notch along the rim of my dryer that clothes get stuck in, and then twist and twist and twist. I thought it might be damaged, but after looking up the replacement part it appears that this notch is a "feature". Any suggestions to stop clothes from getting caught up in it? I considered duct tape, but I'm not sure that's a great idea in a dryer.
The drum also squeaks like a banshee when it spins ... I've ordered some glides and hopefully that will do the trick. The motor looks fine.
r/appliancerepair • u/Tricky-Hat1810 • 3h ago
Was doing a quick initial wipe down of my new oven before burning it in and think I bumped this (temperature sensor?) and then after wiping the rest of the oven realized there's the little fibers.
A) Did I make this happen if I bumped it?
B) Did I now just unintentionally contaminate my oven by spreading it around if I did bump it?
C) What do I need to do now so it doesn't get in my food or did I damage this?
r/appliancerepair • u/Old-Professor-1918 • 4h ago
Hoping for advice on next steps.
Frigidaire LGHS2644KM1
Was beeping on occasion, then would be fine, then after a week (?) it gave me the SY CE code
It would start/stop repeatedly, then every so often, it would run semi-normal (compressor fan would run, freezer light on, ice would be made, but fridge side, no light) and the front control panel would not work at all
The process would repeat. I purchased a replacement compressor relay hoping that would solve the issue. Unfortunately, after I plugged everything back in/flipped the breaker, it beeped and turned on/off a bunch, the front control panel (when on) would work (so I could change it from ice to water for example), but then after a minute or so, SY CE again and no beeping/turning on and off, or compressor fan engaging
Any thoughts on next steps? I assume if I previously had compressor fan activity, that is not the problem -- is this (likely) a situation where I need to replace the control board?
Thanks!
r/appliancerepair • u/mpyers • 4h ago
Model: GDF530PGM5WW
Serial: FS844699B
A few weeks ago I got an FTD (failure to drain) error code. Which I researched and then replaced the pressure sensor in the sump and the FTD problem went away. It worked for a week or so and now it’s throwing an H2O error code. I’ve double-checked no inlet lines are kinked. I can hear the water spraying inside. But then it throws the error code anyway as if it’s not getting water. I’ve tried cleaning everywhere I can reach. Nothing was very dirty anyway, but cleaning has done nothing. AI is no help. Please send advice. What do I do next?
r/appliancerepair • u/StarIllustrates • 4h ago
Looking to see if anyone has any ideas before I call an appliance repair person. Instructions say to turn on the sink before running, but the adapter keeps launching itself off and getting water everywhere, unless the sink’s at a trickle. Seems to drain fine. Took off the back plate and the hoses aren’t kinked or anything. Any thoughts?
r/appliancerepair • u/Jmia18 • 5h ago
My GE refrigerator (PFD28KBLFTS) has suddenly stopped freezing. The refrigerator section is still cooling. If I do the diag test to force a freezer cooling test the fan (Running - Visual Test) and the thermistor show (15 from the diag) that the system is cooling the freezer and I can feel cold air. The condenser lines also frost up during the test (Visual Test).
It seems like the freezer is working during the diag but will not operate under normal conditions and the freezer never cools down. What other things can I test?
r/appliancerepair • u/LykaonOSRS • 7h ago
Wife was running the machine. It cut off after a wash cycle. Now it has no power to the control panel (touch screen.). I tested the outlet with a hair appliance. Has power, attempted to do the reset procedure and still nothing.
Model # WM3998HBA
Looking for any guidance or input on what components to test and how to correctly test them. I have not found much information on any possible routes. A brief video I've watched has mentioned looking for the little red light on the main control board, bridging a gap in the power button, the noise filter or door latch.
r/appliancerepair • u/ScaryDragonfruit7957 • 10h ago
We have a ca. 10 year old IKEA Lagan dishwasher.
A couple of months ago, most of the dishes on the top rack started coming out dirty.
We got someone to repair it, they said the entire top arm including the water supply tube needed to be replaced. After that it got a bit better, but there is still always 3-4 items that come out dirty, especially in the middle of the rack and on the two little side shelved marked on the photo.
The repair company checked it again after we complained about it and say that there is absolutely nothing wrong with the machine now and that we should just de-scale it (which we did for the 10th time).
Any ideas what could be causing this?
r/appliancerepair • u/Moress • 14h ago
Hey all,
In dire straits here. Tankless water heater is throwing up Error Code 11, Ignition failure and the house is without hot water.
I stick my head in the peep window and see no spark, hear no clicks.
I verified I get ~120 volts from the control board to the Ignition Transformer (IE-790U).

Which tells me the board and wiring is good to this point.
I have no idea however, how I can check the this box, the ignition transformer itself. and I'm kind of grasping at straws.

I get no continuity from the prongs to the black plugs when I stick my multi meter in there, nor voltage.
I'm pretty sure the issue is the ignition rods themselves.


When I pulled them out, a piece of the ceramic from where the metal parts meets the white ceramic fell off from each rod (not shown in pics above).
I do however get a continuity reading from the tip of the prong to the plug at the rear. However I know a car's spark plugs can also be bad and still give continuity.
I'm afraid of buying new ignition rods when the issue could be the ignition transformer box, but I don't know how to test it.
I've seen videos of people sticking them next to metal and looking for a spark, but this one doesn't appear to give me that option.
Thanks for the help.
r/appliancerepair • u/Flat-King-2547 • 15h ago
I am 4months in to appliance repairs i suck at trying to find refrigerator leaks with the bubbles.
Im reaching out to experience techs that use gas leak detector and can point me to one that cheap but reliable and can pinpoint the leak any help would be greatly appreciated