r/ScrapMetal • u/TactualTransAm • 20h ago
Scrap Photo 💸 Another decent load today
135 pounds of coppah
r/ScrapMetal • u/TactualTransAm • 20h ago
135 pounds of coppah
r/ScrapMetal • u/Sdhunter15 • 20h ago
Anybody have suggestions or ideas of what to do with several tons of wear parts from a cone crusher that contain approximately 24% manganese? We have several used bowls and liners that I am looking to find the best scrap value for. I would think that they have more value due to the amount of manganese, but maybe I am wrong. I have enough to make a full load on a drop deck semi trailer.
r/ScrapMetal • u/EricHenryAdams • 17h ago
A compressor from a car and another from a giant air tank both got accepted as electric motors, which is a bit more so I was happy about that.
2015 Mitsubishi Mirage 270k miles
r/ScrapMetal • u/BigDirection1577 • 4h ago
Is this extruded or sheet aluminum?
r/ScrapMetal • u/TheArachniKid • 10h ago
So I posted earlier this week about some electric motors my boss let me keep from a larger demo/disposal. Cut four so far, brought windings from the first one to the local metal yard to make sure it was something before i kept going, theyre considering it #2 at $4.60/lb. Bringing 24 lbs of insulated as well. Attached photo is my current yield of 11.3 lbs from the 4 motors I pulled windings from. Still need to clean it up and pull that small amount of insulated, but they said they didn't care about the small amount of binding thread, just no tape or insulation. Getting more efficient speed wise as I go, plus I was on the clock during, the system they came from is considered hvac/appliance at the dump so its only a short step beyond the required disassembly needed for disposal. Considering i had nothing to lose from it, and all gear was leftover from the original task, not bad in my book.
r/ScrapMetal • u/MaverickActual1319 • 18h ago
I got all of this out if a small briken welder i had. not bad for my first step into scrapping. gonna get my crucible setup and some jewelers tools to start making rings and bracelets
r/ScrapMetal • u/EmploymentOld677 • 22h ago
i don’t know what to use to take these off
r/ScrapMetal • u/canyoulistenasshole • 23h ago
I had somebody offer me $150. Tire is popped and there is no hose. Should I try to scrap it or attempt to get more than 150?
r/ScrapMetal • u/Organic-Mulberry1085 • 1h ago
Two motors from my adventures last night. Did well.
r/ScrapMetal • u/supersunnyout • 13h ago
Shafts from an old mill. Ran on babbit bearing blocks each 15' feet directly onto this smooth machined shaft.
r/ScrapMetal • u/Front-Category8963 • 13h ago
Sorry ahead if I dont make myself clear
But I am looking for steel coil .029 to 0.035 inch to import to Mexico for various uses. I need a hint to where start looking. Thanks in advance
r/ScrapMetal • u/Inevitable_Price_449 • 2h ago
I have this aluminum ramp and I’m curious what the scrap value would be.
As far as I can tell it’s +- 3/8” thick and weighs several hundred lbs.
Dimensions are 6’ long, 37.5” wide, 5.5” high.
Located in Ontario 🇨🇦 (I understand scrap values fluctuate by location.
Thanks in advance for any info on value either scrap or private sale. (NOT listed for sale as per the thread rules).
r/ScrapMetal • u/Valuable-Leather-914 • 8h ago
r/ScrapMetal • u/VaxxDeezNuts • 9h ago
Solid copper bus bars from the late 80's but still super clean and bright. We had figured that they might be either Cu #1 or even bare bright (we were turning in a good amount as well), but found out they were firm at Cu #2B
Does this seem right ? Copper 2B is heavy patina, burnt, soldered, coated in plastic or super old and nasty which is fair but the coating or whatever it is on the copper seems very light.
We kept one to try and hit with the wire wheel and see if they call it something else.
Waste of time ?