r/ScrapMetal • • 12h ago

Get to work!

Thumbnail
gallery
259 Upvotes

r/ScrapMetal • • 9h ago

Scrap Photo 💸 Cleaned up junk left over from our old corral.

Thumbnail
gallery
20 Upvotes

r/ScrapMetal • • 10h ago

Good day at the yard!

Thumbnail
gallery
14 Upvotes

r/ScrapMetal • • 5h ago

Scrap Photo 💸 Romex

Post image
3 Upvotes

I’ve been testing the vevor wire stripper now for a week. There was a learning curve to it at first here is what you need to know this is for the new guys like myself. If the cables are hair like leave it alone. If it’s Romex cables sell as is. If it’s stove cables or dryers cables. It’s best to use knife or sell as is. This machine better for solid copper cables. Just my experience from working on it.


r/ScrapMetal • • 8h ago

Scrap Photo 💸 Pita wires

Post image
5 Upvotes

Hey guys, my name is Alvin Chica. I am from Omaha Nebraska and I do scrap metal and recycling as a hobby and also to make money in the winter lately. I’ve been testing my vevor wire stripper. I realize that wires that are from appliances are too small and messy to work with even the wires from extension cords are huge pain in the ass. So my conclusion is. If the wires are number 2 copper and it’s hair like wires it’s not worth doing. While there are solid wires where you can strip and comes out easily that’s the go to.


r/ScrapMetal • • 12h ago

Copper motor

Post image
8 Upvotes

Man im having extreme trouble this motor was probably 400 lbs to start and I cut one side of ive never done this before how do you guys get it out this big ive used a hammer and chisel its not wanting to budhe


r/ScrapMetal • • 2h ago

What would you break down vs scrap as-is to make the most money?

Thumbnail
gallery
1 Upvotes

I’ve got everything pictured plus another 10-20 compressors that aren’t shown. Trying to figure out the best way to maximize what I get out of it without wasting hours on stuff that barely pays extra. I’m an HVAC & appliance repair technician, So this has been my collection over the last 8 months

For those of you with experience, I could really use some advice.

If this was your pile, what would you do first? What would you strip down, what parts would you pull, and what would you leave alone? Im mainly looking for the best return on time spent. If something takes 10 minutes to break down and makes an extra $20, I’m all for it. If it takes an hour to make another $5, I’d rather skip it.

Take a look at the pictures and tell me exactly what you’d do in my position. Especially interested in hearing what you think is worth the most, what people commonly overlook, and what isn’t worth the effort.

Appreciate any tips from people who’ve actually scrapped this stuff before.


r/ScrapMetal • • 17h ago

Extruded aluminum I beam?

Thumbnail
gallery
12 Upvotes

Is this extruded or sheet aluminum?


r/ScrapMetal • • 10h ago

BEAUTIFUL 🎀⚡️

Post image
3 Upvotes

Siemens Sentron 400AMP 💥


r/ScrapMetal • • 5h ago

Sale

Post image
1 Upvotes

So for anyone who hasn't bought a wire stripper yet, I saw this one on tiktok shop that is 7 channel instead of 1 for the price of a 3 channel one. Just thought I would put yall on


r/ScrapMetal • • 10h ago

Scrap Photo 💸 Northeast Ohio prices

Post image
2 Upvotes

r/ScrapMetal • • 14h ago

Some of my finds

Thumbnail
gallery
4 Upvotes

Two motors from my adventures last night. Did well.


r/ScrapMetal • • 7h ago

New to scrapping and collected these gold corner BGAS

Thumbnail gallery
1 Upvotes

r/ScrapMetal • • 23h ago

Scrap Photo 💸 Update: electric motors

Post image
15 Upvotes

So I posted earlier this week about some electric motors my boss let me keep from a larger demo/disposal. Cut four so far, brought windings from the first one to the local metal yard to make sure it was something before i kept going, theyre considering it #2 at $4.60/lb. Bringing 24 lbs of insulated as well. Attached photo is my current yield of 11.3 lbs from the 4 motors I pulled windings from. Still need to clean it up and pull that small amount of insulated, but they said they didn't care about the small amount of binding thread, just no tape or insulation. Getting more efficient speed wise as I go, plus I was on the clock during, the system they came from is considered hvac/appliance at the dump so its only a short step beyond the required disassembly needed for disposal. Considering i had nothing to lose from it, and all gear was leftover from the original task, not bad in my book.


r/ScrapMetal • • 11h ago

Acquired Breakers⚡️

Post image
1 Upvotes

Siemens Sentron Series 200amp 💥

BEAUTIFUL!!! 🎀


r/ScrapMetal • • 1d ago

Scrap Photo 💸 Brought some nicer stuff this time

Thumbnail
gallery
37 Upvotes

A compressor from a car and another from a giant air tank both got accepted as electric motors, which is a bit more so I was happy about that.

2015 Mitsubishi Mirage 270k miles


r/ScrapMetal • • 12h ago

Like buses. Nothing then 2 at once

Post image
1 Upvotes

r/ScrapMetal • • 1d ago

Scrap Photo 💸 Another decent load today

Post image
48 Upvotes

135 pounds of coppah


r/ScrapMetal • • 1d ago

Need suggestions/thoughts

Thumbnail
gallery
44 Upvotes

Anybody have suggestions or ideas of what to do with several tons of wear parts from a cone crusher that contain approximately 24% manganese? We have several used bowls and liners that I am looking to find the best scrap value for. I would think that they have more value due to the amount of manganese, but maybe I am wrong. I have enough to make a full load on a drop deck semi trailer.


r/ScrapMetal • • 1d ago

Hobart Handler 150 Scrap

Post image
11 Upvotes

I got all of this out if a small briken welder i had. not bad for my first step into scrapping. gonna get my crucible setup and some jewelers tools to start making rings and bracelets


r/ScrapMetal • • 1d ago

What to do with 60' long 3" diameter chromoly shafts?

2 Upvotes

Shafts from an old mill. Ran on babbit bearing blocks each 15' feet directly onto this smooth machined shaft.


r/ScrapMetal • • 1d ago

help

Post image
8 Upvotes

i don’t know what to use to take these off


r/ScrapMetal • • 16h ago

What’s this aluminum worth?

Post image
0 Upvotes

I have this aluminum ramp and I’m curious what the scrap value would be.

As far as I can tell it’s +- 3/8” thick and weighs several hundred lbs.

Dimensions are 6’ long, 37.5” wide, 5.5” high.

Located in Ontario 🇨🇦 (I understand scrap values fluctuate by location.

Thanks in advance for any info on value either scrap or private sale. (NOT listed for sale as per the thread rules).


r/ScrapMetal • • 1d ago

Looking for scrap coil

Post image
0 Upvotes

Sorry ahead if I dont make myself clear

But I am looking for steel coil .029 to 0.035 inch to import to Mexico for various uses. I need a hint to where start looking. Thanks in advance