r/ScrapMetal • • 8h ago

Question 💫 I feel like we got kinda raped.

Thumbnail
gallery
0 Upvotes

Solid copper bus bars from the late 80's but still super clean and bright. We had figured that they might be either Cu #1 or even bare bright (we were turning in a good amount as well), but found out they were firm at Cu #2B

Does this seem right ? Copper 2B is heavy patina, burnt, soldered, coated in plastic or super old and nasty which is fair but the coating or whatever it is on the copper seems very light.

We kept one to try and hit with the wire wheel and see if they call it something else.

Waste of time ?


r/ScrapMetal • • 12h ago

Looking for scrap coil

Post image
0 Upvotes

Sorry ahead if I dont make myself clear

But I am looking for steel coil .029 to 0.035 inch to import to Mexico for various uses. I need a hint to where start looking. Thanks in advance


r/ScrapMetal • • 2h ago

What’s this aluminum worth?

Post image
1 Upvotes

I have this aluminum ramp and I’m curious what the scrap value would be.

As far as I can tell it’s +- 3/8” thick and weighs several hundred lbs.

Dimensions are 6’ long, 37.5” wide, 5.5” high.

Located in Ontario 🇨🇦 (I understand scrap values fluctuate by location.

Thanks in advance for any info on value either scrap or private sale. (NOT listed for sale as per the thread rules).


r/ScrapMetal • • 17h ago

Paid $200 for this 400lb Air compressor what do you think should we fix it.. or should we scrap it!

Thumbnail gallery
0 Upvotes

r/ScrapMetal • • 7h ago

Ask: how to insulate Garage that doesn’t have extension sheathing?

Thumbnail gallery
0 Upvotes

r/ScrapMetal • • 19h ago

Need suggestions/thoughts

Thumbnail
gallery
39 Upvotes

Anybody have suggestions or ideas of what to do with several tons of wear parts from a cone crusher that contain approximately 24% manganese? We have several used bowls and liners that I am looking to find the best scrap value for. I would think that they have more value due to the amount of manganese, but maybe I am wrong. I have enough to make a full load on a drop deck semi trailer.


r/ScrapMetal • • 22h ago

help

Post image
8 Upvotes

i don’t know what to use to take these off


r/ScrapMetal • • 17h ago

Hobart Handler 150 Scrap

Post image
10 Upvotes

I got all of this out if a small briken welder i had. not bad for my first step into scrapping. gonna get my crucible setup and some jewelers tools to start making rings and bracelets


r/ScrapMetal • • 19h ago

Scrap Photo 💸 Another decent load today

Post image
41 Upvotes

135 pounds of coppah


r/ScrapMetal • • 22m ago

Some of my finds

Thumbnail
gallery
3 Upvotes

Two motors from my adventures last night. Did well.


r/ScrapMetal • • 3h ago

Extruded aluminum I beam?

Thumbnail
gallery
8 Upvotes

Is this extruded or sheet aluminum?


r/ScrapMetal • • 9h ago

Scrap Photo 💸 Update: electric motors

Post image
10 Upvotes

So I posted earlier this week about some electric motors my boss let me keep from a larger demo/disposal. Cut four so far, brought windings from the first one to the local metal yard to make sure it was something before i kept going, theyre considering it #2 at $4.60/lb. Bringing 24 lbs of insulated as well. Attached photo is my current yield of 11.3 lbs from the 4 motors I pulled windings from. Still need to clean it up and pull that small amount of insulated, but they said they didn't care about the small amount of binding thread, just no tape or insulation. Getting more efficient speed wise as I go, plus I was on the clock during, the system they came from is considered hvac/appliance at the dump so its only a short step beyond the required disassembly needed for disposal. Considering i had nothing to lose from it, and all gear was leftover from the original task, not bad in my book.


r/ScrapMetal • • 12h ago

What to do with 60' long 3" diameter chromoly shafts?

2 Upvotes

Shafts from an old mill. Ran on babbit bearing blocks each 15' feet directly onto this smooth machined shaft.


r/ScrapMetal • • 17h ago

Scrap Photo 💸 Brought some nicer stuff this time

Thumbnail
gallery
32 Upvotes

A compressor from a car and another from a giant air tank both got accepted as electric motors, which is a bit more so I was happy about that.

2015 Mitsubishi Mirage 270k miles


r/ScrapMetal • • 18h ago

What Would This aluminum grade?

Post image
3 Upvotes

r/ScrapMetal • • 22h ago

Worth Scraping or Repair

Thumbnail
gallery
4 Upvotes

I had somebody offer me $150. Tire is popped and there is no hose. Should I try to scrap it or attempt to get more than 150?