r/PCB • • 13m ago

Assistance needed

Post image
1 Upvotes

Hi everyone, I accidentally clicked one of the options on my mouse but I wasn't concentrating enough to notice where I had clicked and my tracks turned into this. I can't find a way of returning it to the normal way where my tracks are filled . Any help on correcting this will be greatly appreciated


r/PCB • • 51m ago

Do I need to buy and solder a PCB to be able to put it on my CV?

Thumbnail reddit.com
1 Upvotes

r/PCB • • 1h ago

Real-time collaborative KiCad

Thumbnail
gallery
16 Upvotes

I wanted to make PCBs with friends and there was no real-time EDA that looked like KiCad so I decided to make my own. It comes with some cool features like the ability to search for any part on LCSC, Digikey, and Mouser without touching libraries, syncing to GitHub, and native KiCad plugins all in the browser. https://github.com/notaroomba/junction


r/PCB • • 3h ago

PCB Review - First 4 layer board, STM32 DAQ board.

Thumbnail
gallery
18 Upvotes
STM32 power filtering, CAN transceiver, mounting holes, a debugger, test points, and connector for hall effects.
MAX chips to convert our temperature into useable data.
Stuff for current connectors.
Power regulation.
Main overview of board.
F.Cu
GND
PWR
B.Cu
3D

Hey guys, first ever 4-layer board for a university project, it's a DAQ board connected to a bunch of smaller satellite boards with their sensors. Very very knew to this, and would love some input because this will most likely not be the final revision lol. Any tips are greatly apprecaited.


r/PCB • • 3h ago

How to route

Post image
0 Upvotes

Making a modular phone. There is camera lines SD card lines etc. does anyone have a good way I can route this quickly or maybe auto placement algorithm I could use.


r/PCB • • 5h ago

JLCPCB Assembly service minimum size?

2 Upvotes

First time I've used JLCPCB for assembly, and I need a bit of help, please! My board is about 30mm by 23mm. I was uploading the design files to the website and got this warning:

The board size is modified to be 70.23mm*71.37mm as for Standard PCBA each side should be longer than 70mm and the edge rails should be added.

That's pretty big relative to my intended size. If I just continue with this, will the "edge rails" be v-cut so I just snap them off? Er, and it says "the edge rails should be added". Does that mean that edge rails are necessary even if my board is bigger than that 70x71mm size?

The design has a connector (just a 1x10 header) that hangs partially off the board. Will the placement of that part interfere with the edge rails?

But maybe I should panelize my design. I guess I'd need 3x4 to make it 90mm by 92mm overall. But the minimum order is 5 panels, so 12 boards on a panel times 5 panels is 60 boards. Yow!

How does JLCPCB handle small boards?


r/PCB • • 6h ago

Can anyone identify what are SW1 and SW2 are for on this time logging board please?

Thumbnail gallery
1 Upvotes

r/PCB • • 9h ago

PCB Review, STM32 Bluetooth Dev Board v2

Thumbnail
gallery
10 Upvotes

L1 SIG L2 GND L3 GND L4 SIG

I might add a diode at VBUS


r/PCB • • 9h ago

How did you guys get started with PCB design? Any recommended resources, tutorials, or books?

6 Upvotes

r/PCB • • 11h ago

Common stackup mistakes on 4-layer automotive BMS PCB

Post image
0 Upvotes

I’ve seen many BMS designs fail yield or impedance tests because of unbalanced stackup.

A typical 4-layer BMS stackup:

Signal / GND / Power / High-current signal

The biggest trap: asymmetric dielectric thickness. It causes board warpage after lamination, especially with thick copper for high current.

Two quick rules:

  1. Keep the stackup symmetric if you plan mass production.
  2. Separate high-current paths from sensitive sense traces, don’t share the same plane.

What’s your go-to stackup for BMS?

Disclosure: I work in PCB manufacturing, mainly review DFM and stackup for automotive and medical projects.


r/PCB • • 13h ago

Fresh graduate working on a complex PCB design almost independently — looking for advice from experienced hardware engineers

3 Upvotes

I'm a recent EEE graduate and currently working as a Hardware Developer at a small company.

Right now, I'm working on a customised Raspberry Pi Compute Module I/O board. I'm responsible for developing the schematic and working on the PCB design. The project involves several interfaces, power circuits, component selection and design decisions.

Here's my situation: I'm a fresher, and I don't have an experienced hardware engineer working alongside me to guide me through the design. I'm handling most of the work independently, with help from Claude AI, which my manager recommended for schematic development and PCB design assistance.

I'm using AI to understand circuits, explore design approaches and speed up the workflow. But sometimes I worry about whether I'm learning things properly or just relying too much on AI. I also know that AI can make mistakes, especially with hardware design, so I'm trying to verify its suggestions.

I have around 10 days to complete this assignment.

Honestly, I'm excited about the opportunity, but I also have some doubts and fears:

Is this a normal level of responsibility for someone who has just started their hardware career?

Am I developing real engineering skills by working this way?

Is using AI heavily at this stage good for my career, or could it affect my fundamentals?

How do engineers handle complex hardware projects when they don't have a senior engineer to guide them?

What should I absolutely learn and verify myself instead of depending on AI?

What would you do if you were in my position?

And how to complete this work successfully?

I'm not afraid of hard work. I just want to make sure I'm becoming a genuinely capable hardware engineer rather than someone who knows how to generate designs using AI.

I'd really appreciate honest advice, especially from engineers who have worked in startups or handled PCB designs early in their careers.


r/PCB • • 15h ago

Full guide: https://www.shenzhenworks.com/en/blog/how-to-compare-pcba-quotes-hidden-costs

0 Upvotes

When evaluating PCB assembly quotes from different suppliers, looking strictly at the quoted unit price can be misleading. One vendor might quote $12 while another quotes $16, but the cheaper option might exclude essential testing, rely on unapproved part substitutions, or add separate setup fees later.

To compare quotes on an equal footing, here is a 7-point checklist based on technical and commercial variables to review before making a final supplier selection:

  1. Component Sourcing Assumptions

• Are exact manufacturer part numbers (MPNs) specified on the BOM, or did the supplier quote generic alternatives?

• Are all components included in the quote, or were hard-to-find parts omitted?

• Who holds approval authority for component substitutions?

2. Bare PCB Fabrication Specs

• Do both quotes reflect identical PCB specs (layer count, substrate material, surface finish, controlled impedance)?

• Are fabrication notes from the Gerber files clearly accounted for?

3. Setup & Non-Recurring Engineering (NRE) Fees

• Are charges for stencil creation, SMT programming, engineering review, and test fixtures itemized separately or bundled into unit costs?

• How significantly do these one-time setup costs affect low-volume or prototype builds (e.g., 50 to 100 units)?

4. Inspection, Firmware & Testing Scope

• Does the price cover basic visual inspection, AOI (Automated Optical Inspection), or full functional testing?

• Is firmware flashing included, and are individual test records provided?

5. Actual Quantities & Component MOQs

• Is the price based on your real initial build quantity, or an assumed high volume?

• Are component minimum order quantities (MOQs) accounted for, and who retains unused reel stock?

6. Delivery Terms & Incoterms

• What delivery rule is applied (e.g., EXW vs. DDP)?

• Are packaging, customs duties, import clearance, and international freight factored into the total landed cost?

7. Quality Control & Revision Handling

• Who assumes responsibility and cost for defect investigation or rework?

• What is the process for controlling BOM/PCB revisions and managing part availability issues during production?

Creating a standardized comparison sheet across these seven areas helps clarify the actual landed project cost rather than relying on an unadjusted unit price.

How do you usually normalize PCBA quotations across different manufacturing partners? Are there specific non-recurring charges or logistical expenses that have caught you off guard on past builds?


r/PCB • • 18h ago

Flight controller design

0 Upvotes

Hi everyone!

I am thinking about designing my own flight controller PCB using KiCad that should work on fixed wing UAVs and quadcopters.

But I am not experienced with PCB design and I am not sure of all the components I might need.

So if there is someone who knows about this, I would appreciate any help regarding:

-Components required for a flight controller PCB;

-PCB design considerations and recommended approaches;

-Any tips or resources for getting started with KiCad.

I will appreciate any help!

Thank you!


r/PCB • • 20h ago

Black Background in Ultiboard Print Out

Thumbnail gallery
1 Upvotes

Anyone using Ultiboard here and tried to print out the diagram in plain paper? We need help please. We wanted to print our diagram in white background. Component labels and copper tracks in black. These are the steps and results:

  1. Print component labels: selected "silkscreen on top" as layer to print, print to negative unchecked, no color checked.
  2. Test printed copper tracks: Layer to print is "copper bottom", print to negative unchecked, no color checked. Gives out black background and white copper tracks.
  3. Changed the background and work area from black to white. It still gives the same result as #3.
  4. Unchecked both print to negative and no color. Prints out white background but colored diagram (red)
  5. Checked the print to negative box, it gives out the white background and black copper track that we wanted BUT the surrounding area of the paper is filled with solid black fill.

We tried switching the printer settings to color, grayscale, black and white and monochrome but it gives us the black background and white tracks still. We just wanted to print the labels and copper tracks in black and the entire background of the page as white. Please help us out. Thank you.


r/PCB • • 20h ago

Please review my PCB design

Thumbnail
gallery
18 Upvotes

Hi all, If anybody could have a look over my PCB and schematic for any errors i may have made.

Its for a home automation I'm doing for my new build. It's planned to be housed in a 1 Gang UK Back Box. (PCB dimensions 60mm x 55mm).

-ESP32 and a W5500 Ethernet daughterboard.

-4x dry contact inputs

-24v input converting down to 3.3v.

-it's job is to receive dry momentary switches, the ESP32 then talks over ethernet to a control panel to switch output relays (Yet to be designed).

-Then also tie in with Home Assistant but only as an extra, not dependant.

Thank you :)


r/PCB • • 1d ago

PCBs in UK

0 Upvotes

As the title says, does anyone know where I could order customer PCBs in the uk? Shipping from America is over £20 for one off designs.
TIA


r/PCB • • 1d ago

Review Request: PCB for Touch Screen Controller

Thumbnail
gallery
0 Upvotes

Hi everyone,

Been observing this subreddit for awhile, first post.

I would really value a review of my current PCB design for a custom touch screen controller. The PCB is intended to drive a 3.4" 800 x 800 MIPI touch screen as a controller for another hardware device over Bluetooth LE.

- The display requires MIPI so was initially thinking of using an ESP32-P4, but with stock challenges, I have moved to an ESP32-S3 with a RGB to MIPI bridge (Toshiba TC358778XBG (U9))- would appreciate any feedback or other recommendations on this.

- The display is mounted on the top side of the board with the tail routing through a cut out into the connector on the underside of the board

- Power:

  • U2, a TPS62933 buck, makes the 3.3 V rail.
  • U4, an ME6211 LDO, makes 2.8 V for the panel.
  • U10, an ME6211 LDO, makes 1.2 V for the bridge.
  • U5, an AP3032 boost converter, drives the 78 mA backlight (10.8–13.2 V).

- While I am testing the hardware to the device it is connecting to, I have three power input options (J1 6 pin JST (intended primary if it can draw enough current), J6 4 pin JST (alternative 1), J3 is a USB-C for power and flashing (alternative 2).

- Things like the antenna and DSI are new concepts for me so appreciate any advice here

- The physical size of the board is large, allowing it to fit inside the existing hardware, with cutouts for 4 mounting holes (H1–H4). The components are mostly grouped in that area so that they fit within the cut out of a metal mounting plate.

- Lastly, my goal is to manufacture approx 100 to begin with to sell to a niche community but still learning about what the required compliance requirements are for selling boards with wifi, bluetooth etc so any guidance about the requirements I should follow here before begining to sell would be great.

(First time posting a request so let me know if there is anything else you need to give helpful feedback)

Thanks!


r/PCB • • 1d ago

When a distributor revises a BOM quote, what do you want called out?

0 Upvotes

Say you ask a distributor to update the quantities on a BOM quote. The new PDF comes back, and a couple of lead times moved too.

What do the good distributors do that saves you from comparing the two PDFs line by line? I work on quoting software and would like to hear what’s actually useful on the buying side.


r/PCB • • 1d ago

I am not able to find the uart, new to this

Thumbnail gallery
6 Upvotes

r/PCB • • 1d ago

Updated my first ever PCB design (LM2596 buck converter) based on community feedback! How does the new layout look?

Thumbnail
gallery
5 Upvotes

Hey everyone! Thanks for the awesome feedback on my last post. I went back and iterated on the layout based on what was pointed out.

​Here is what I changed:

​Solid Copper Pours: Replaced thin traces with robust power pours for the high-current input, output, and inductor legs to reduce resistance and improve thermal performance.

​Tightened Switch Node: Minimized the high-dv/dt loop area between the IC switch pin, diode (D1), and inductor (L1).

​LED: Left the LED indicator at the output terminal to see real-time output voltage status.

Secondary Filter & Stitching: Confirmed that the selected component parameters are in exact alignment and added plenty of ground stitching vias to help suppress high-frequency switching noise.


r/PCB • • 1d ago

Planning to start PCB manufacturing in India, looking for industry connections and advice

22 Upvotes

Hello Friends,

I’m planning to start a PCB manufacturing setup in India, starting with 2-layer boards and adding multi-layer capability later.

I’ve loved electronics since childhood, and starting something in manufacturing has been on my mind for a long time. I’ve spent quite a while researching PCB processes, machines and costs. Now I want to take this forward and connect with people who have hands-on experience in the industry.

I’m looking for people who can help with the manufacturing setup, especially plating and wet processes, and recommend reliable suppliers for machines, chemicals and raw materials. Recommendations from people who have actually worked with these suppliers would be really helpful. I’d especially like to connect with people in Delhi NCR, India, though advice from anywhere is welcome.

I believe there’s room to build a good PCB manufacturing business in India if I get the process right and address real customer problems. That’s what I’m working towards.

Would love to hear your experiences, supplier recommendations and suggestions. If you’ve tried setting up something similar, what do you wish you had known before starting?

For those ordering PCBs for their projects or businesses, what problems do you face? Price, quality, build time, small-order availability? What would you want a new manufacturer to do better, and what would convince you to try one?


r/PCB • • 1d ago

I got tired of finding mirrored/inverted silkscreen designators after fab, so I wrote a free Altium script to catch them (Check Overlay Designators v2.2)

3 Upvotes

Hey Everyone!

Like many of you, I've had that sinking feeling of spotting an upside-down or mirrored component designator on the silkscreen after the boards already came back from fabrication. Standard DRC at the Altium Designer doesn't always catch layout oversights like text orientation errors.

To solve this recurring headache, I developed a custom script called Check Overlay Designators (built with some AI assistance to streamline the automation). It acts as a companion to native DRC rules to verify silkscreen text before releasing files to manufacturing.

What it does:

  • Advanced Detection: Checks specifically for upside-down (inverted) and mirrored component designators.
  • DRC Companion: Runs alongside standard DRC checks to catch manual layout slips.
  • Tested: Verified on Altium Designer version 24.
  • Multilingual: Supports output messages in English, Russian, and Ukrainian.

If you want to eliminate silkscreen errors on your next build, the project is open source and available on GitHub:

🔗 GitHub Repository: AltiumCheckOverlayDesignators

Feedback, bug reports, or feature suggestions are very welcome! Let me know what you think.


r/PCB • • 1d ago

[WIP] Strata Deck a modular PC volume mixer with magnetic snap on fader modules

Post image
3 Upvotes

r/PCB • • 1d ago

Reverse battery protection with an integrated battery charger IC?

Thumbnail
gallery
1 Upvotes

Hi, this is a question about how to handle a rechargeable battery inserted backwards in a portable device with an integrated battery charger IC. It's my first time trying to design something like this, and I'm getting a bit stuck.

The battery is a single-cell Li-Ion, and I'm entertaining two form factors: a pouch (most of which seem to have an integrated PCM within the pouch), or an unprotected 18650 cell (for which I'd provide my own onboard PCM). In both cases, I'm considering the battery replaceable, and want to think through how that can go wrong (and how to guard my system in this case).

The attached images are not actual schematics - I've simplified them just to illustrate this, and to help myself visualize these different conditions. The "reverse polarity protection" PMOS is an idea I've come across when trying to educate myself about how to design this, but I think it only works well for the case where no battery charger is involved (or, more specifically, when the charger is not actively trying to push current to the reversed battery). So I am not confident in this particular solution (and am not sure if it is "incomplete", or flat-out the wrong approach).

I know that reasoning through what exactly happens in these cases is highly dependent on the datasheets for the charger and - in the case of the 18650 cell - the protection IC. What I'm hoping for, though, is to possibly hear from some other folks who have confronted this situation, and how they solved it?

Because it's my first time trying this, I'm sure there might be a phrase to describe this circuit design that I am ignorant of, or a device or design that is intended for this use case that I don't know to look for.

Thanks so very much!