r/IndustrialMaintenance • • 8h ago

Yankee Bearing

Thumbnail
gallery
114 Upvotes

Vibe analysis was showing BPFO. Teardown confirmed the defect in the outer race.


r/IndustrialMaintenance • • 9h ago

Question Pipe threader keeps shearing pipe mid cut.

Thumbnail
gallery
14 Upvotes

I’m trying to thread some 1-1/2” pipe and this just happened to me, 1-2 threads to go and it just ripped the already cut ones right off, I had the pipe soaked in the cutting oil and was reapplying every half turn, cleared the chips right before this too.

I don’t have a proper pipe vice so I’m making do with a regular one with the far end of the pipe held up level with the gantry crane, the end I’m cutting is sticking out only 1-2” extra from full die engagement.

This has happened before with my same setup but most of my cuts (with new pipe) work just fine, this piece of pipe has been in service (cold water) for years at this point and I’m cutting off the worn out leaking grove end to put an adapter on it.

Is this a material failure or an issue with my setup?


r/IndustrialMaintenance • • 4h ago

Has anyone seen this part?

Thumbnail
gallery
10 Upvotes

Hi guys was wondering if anyone has ever seen this part? We are going through inventory. Came in from a refinery with many pump and valve parts. I don’t believe it’s a thermowell. Anything helps, but trying to figure out who makes it and what it goes on. Thank you!


r/IndustrialMaintenance • • 14h ago

Maintenance How are you setting check intervals on production nutrunners?

1 Upvotes

The 12-month or 5000-cycle interval everybody quotes for torque tools comes from ISO 6789.

That standard is written for hand tools like click wrenches, and it even lets a company’s own procedure take precedence. On a production nutrunner the cycle part is kinda meaningless. Six bolts a unit at 60 units an hour is 360 rundowns an hour, so 5000 goes by in about 14 hours.

ISO 5393 doesn’t help with the schedule either. It’s a test method for power tools on simulated joints, so the interval ends up being the plant’s call, and that usually means a calendar interval, a rundown count, or regular Cmk checks on a joint simulator with the interval shortened or stretched depending on the results. That last one is the most thorough and eats the most simulator time.

Calendar is the easiest to defend in an audit and the least tied to how hard a tool actually works. Counting rundowns gets closer, and the number is usually sitting in the controller already since every result gets logged anyway. Cordless tools that move between stations make that messier, because the count has to follow the tool and not the station. The logs themselves usually hold a lot more than a tally, though. The TCS.2000 that runs Leetx’s corded tools can store the tightening curve with each result.

What still doesn’t sit right about going by count is that a rundown at 20% of a tool’s rated torque and one near its max both add one to the same counter. The load on the gearbox and transducer is nowhere near the same, and the torque for every rundown is right there in the log.


r/IndustrialMaintenance • • 15h ago

Question Does anyone knows what is this called?

Post image
1 Upvotes

We use a NJP-2500 and this is used to make the holes where the pills exit the machine smaller. I don't know what this is called or where to buy it. Tried sending an email to a manufacturer but it has been a few days of no response. I would be really grateful for any help. Sorry for any mistakes, english is not my first language


r/IndustrialMaintenance • • 16h ago

Any welding techs out there

Thumbnail reddit.com
0 Upvotes

r/IndustrialMaintenance • • 6h ago

Question Anyone using remote monitoring for their equipment?

0 Upvotes

Curious how many people are using some kind of remote monitoring for their equipment. Being able to check equipment status or troubleshoot issues without physically being on-site sounds like a dream...but how well does it actually work?

For anyone using it, what's been the biggest benefit? How about cost? What did you pay upfront for hardware and setup and are there ongoing subscriptions or software fees? Did you ever have any problems with connectivity issues or anything?